Related Manuals for SHOWTEC XS-4W Quad Beam
Summary of Contents for SHOWTEC XS-4W Quad Beam
- Page 1 MANUAL ENGLISH XS-4W Quad Beam Ordercode: 40174 Highlite International B.V. – Vestastraat 2 – 6468 EX – Kerkrade – the Netherlands...
-
Page 2: Table Of Contents
Installation ................................... 9 Set Up and Operation ............................... 9 Control Modes ................................9 One XS-4W Quad Beam (Manual Control) ......................9 One XS-4W Quad Beam (Sound-controlled) ....................... 9 Multiple XS-4W Quad Beams (Master/Slave control) ..................9 Multiple XS-4W Quad Beams (DMX Control) ......................10 Fixture Linking ................................11... -
Page 3: Warning
Your shipment includes: ● Showtec XS-4W Quad Beam with IEC powercable 1,5m ● 2 brackets for truss mounting ● Safety eye ●... - Page 4 For replacement use fuses of same type and rating only. The user is responsible for correct positioning and operating of the XS-4W Quad Beam. The manufacturer will not accept liability for damages caused by the misuse or incorrect installation of this device.
-
Page 5: Operating Determinations
When rigging, derigging or servicing the projector, always make sure, that the area below the installation place is blocked and staying in the area is forbidden. The XS-4W Quad Beam can be placed on a flat stage floor, a tripod or mounted to any kind of truss by a clamp. - Page 6 XS-4W Mounting a clamp to the underside of the XS-4W Quad Beam Improper installation can cause serious damage to people and property ! Ordercode: 40174...
-
Page 7: Connection With The Mains
XS-4W Connection with the mains Connect the device to the mains with the power-plug. Always pay attention, that the right color cable is connected to the right place. International EU Cable UK Cable US Cable BROWN YELLOW/COPPER FASE BLUE BLACK SILVER NULL YELLOW/GREEN... -
Page 8: Description Of The Device
XS-4W Description of the device Features The Showtec XS-4W Quad Beam is a bar with 4 moving-heads with high output and great effects. ● Strong white beams ● Compact housing ● Dynamic programs ● Multiple mounting possibilities ● Input Voltage: 100-240 VAC, 50/60Hz ●... -
Page 9: Overview
XS-4W Overview Fig. 01 Lens 02) IEC power connector + Fuse F3A 250V DMX signal connector (OUT) 3-pin DMX signal connector (IN) 3-pin LCD Display + Menu Buttons NOTE: Knowledge of DMX is required to fully utilize this unit. Ordercode: 40174... -
Page 10: Installation
04) When the XS-4W Quad Beam is not connected by a DMX-cable, it functions as a stand-alone device. Turn on the music. If the device is set to sound-control, then the XS-4W Quad Beam will react to the beat of the music. -
Page 11: Multiple Xs-4W Quad Beams (Dmx Control)
XS-4W Multiple XS-4W Quad Beams (Master/Slave control) Fig. 02 Multiple XS-4W Quad Beams (DMX Control) 01) Fasten the effect light onto firm trussing. Leave at least 0,5 meter on all sides for air circulation. 02) Always use a safety cable (ordercode 70140 / 70141). 03) Plug the end of the electric mains power cord into a proper electric power supply socket. -
Page 12: Fixture Linking
DAP Audio cable for the demanding user with exceptional audio-qualities and connector made by Neutrik®. Ordercode FL71150 (1,5m.), FL713 (3m.), FL716 (6m.), FL7110 (10m.). The XS-4W Quad Beam can be operated with a controller in control mode or without the controller in stand-alone mode. -
Page 13: Control Panel
The problem may be: • The XLR cable from the controller is not connected with the input of the XS-4W Quad Beam. • The controller is switched off or defective, the cable or connector is detective, or the signal wires are swapped in the input connector. -
Page 14: Menu Overview
XS-4W Menu Overview Ordercode: 40174... -
Page 15: Main Menu Options
XS-4W Main Menu Options DMX address Pan/Tilt correction Master/Slave Display Sound-controlled Channel Mode (9CH / 28CH) Manual 1. DMX Addressing With this menu you can set the DMX address. 01) Press the MENU button and then the Up / Down buttons, until the display shows 02) Press the ENTER button to open this menu. -
Page 16: Display Inverse
XS-4W 4. Display Inverse With this menu you can set the Display rotation. 01) Press the MENU button and then the Up / Down buttons, until the display shows 02) Press the ENTER button to open this menu. 03) Use the UP/DOWN buttons to change the setting from Off to On. 04) Once you have set the desired Mode, press the ENTER button to store your setting. -
Page 17: Dmx Channels
XS-4W DMX Channels 7 Channels (Basic) Channel 1 – Horizontal movement (Pan) Push the slider up, in order to move head horizontally (PAN). Gradual head adjustment from one end of the slider to the other (0-255, 128-center). The head can be turned by 540° and stopped at any position you wish. Channel 2 –... -
Page 18: Channels (Basic)
XS-4W 28 Channels (Basic) Channel 1 – Head 1 - Horizontal movement (Pan) Push the slider up, in order to move head horizontally (PAN). Gradual head adjustment from one end of the slider to the other (0-255, 128-center). The head can be turned by 540° and stopped at any position you wish. Channel 2 –... - Page 19 XS-4W Channel 16 – Head 3 - Vertical movement (Tilt) Push the slider, up in order to move head vertically (TILT). Gradual head adjustment from one end of the slider to the other (0-255, 128-center). The head can be turned by 270° and stopped at any position you wish. Channel 17 –...
-
Page 20: Channel Settings
XS-4W Channel settings Fig. 05 Ordercode: 40174... -
Page 21: Maintenance
XS-4W Maintenance The Showtec XS-4W Quad Beam requires almost no maintenance. However, you should keep the unit clean. Otherwise, the fixture’s light-output will be significantly reduced. Disconnect the mains power supply and then wipe the cover with a damp cloth. Wipe the front glass panel clean with glass cleaner and a soft cloth. -
Page 22: Troubleshooting
04) If all of the above appears to be O.K., plug the unit in again. 05) If you are unable to determine the cause of the problem, do not open the XS-4W Quad Beam, as this may damage the unit and the warranty will become void. - Page 23 XS-4W Problem Probable cause(s) Remedy One or more No power to the fixture. ● Check that power is switched on and fixtures are cables are plugged in. completely dead. Primary fuse blown. ● Replace fuse. Fixtures reset The controller is not connected. ●...
-
Page 24: Product Specification
XS-4W Product Specification Model: Showtec XS-4W Quad Beam Input Voltage: 100-240 VAC Continuous Power: 80W max. at full output Fuse: F3A / 250V Dimensions: 810 x 90 x 250 mm (LxWxH) Weight: 5,4 kg Operation and Programming Signal pin OUT:... - Page 25 XS-4W Dimensions Ordercode: 40174...
- Page 26 XS-4W Notes Ordercode: 40174...
- Page 27 XS-4W Ordercode: 40174...
- Page 28 ©2014 Showtec...
Need help?
Do you have a question about the XS-4W Quad Beam and is the answer not in the manual?
Questions and answers