Related Manuals for SHOWTEC Pixelbar 16 Q6
Summary of Contents for SHOWTEC Pixelbar 16 Q6
- Page 1 USER MANUAL ENGLISH Pixelbar 16 Q6 Product code: 41308 Highlite International B.V. – Vestastraat 2 – 6468 EX – Kerkrade – the Netherlands...
- Page 2 Pixelbar 16 Q6 Preface Thank you for purchasing this Showtec product. The purpose of this user manual is to provide instructions for the correct and safe use of this product. Keep the user manual for future reference as it is an integral part of the product. The user manual shall be stored at an easily accessible location.
-
Page 3: Table Of Contents
Pixelbar 16 Q6 Table of contents Introduction ................................4 Before Using the Product ..........................4 Intended Use ............................... 4 Product Lifespan ..............................4 LEDs Lifespan ............................... 4 Text Conventions ..............................4 Symbols and Signal Words ..........................5 Symbols on the Information Label ........................5 Safety .................................. - Page 4 Pixelbar 16 Q6 Auto Control ..............................29 Slave Mode ..............................30 Set IP Mode ..............................30 Set IP Address ..............................30 Set Netmask .............................31 Set Net Protocol ............................31 Set Universe..............................31 Set LCD Backlight ...........................33 Set Display ..............................33 Set Default ...............................33 Auto Test ..............................34 Temperature ............................34 Fixture Hours .............................34...
-
Page 5: Introduction
After unpacking, check the contents of the box. If any parts are missing or damaged, contact your Highlite International dealer. Your shipment includes: ● Showtec Pixelbar 16 Q6 ● 2 x mounting brackets ● 2 x adjustment screws ●... -
Page 6: Symbols And Signal Words
Pixelbar 16 Q6 Symbols and Signal Words Safety notes and warnings are indicated throughout the user manual by safety signs. Always follow the instructions provided in this user manual. Indicates an imminently hazardous situation which, if not avoided, will result in DANGER death or serious injury. -
Page 7: Safety
Pixelbar 16 Q6 Safety Important Read and follow the instructions in this user manual before installing, operating or servicing this product. The manufacturer will not accept liability for any resulting damages caused by the non-observance of this manual. Warnings and Safety Instructions... - Page 8 Pixelbar 16 Q6 WARNING Risk of burns due to hot surface The surface and the inner parts of the device can become very hot during operation. ● Do not touch the device during operation. ● Allow the device to cool down for at least 15 minutes before handling.
-
Page 9: Requirements For The User
Pixelbar 16 Q6 ● If the device is exposed to extreme temperature variations (e.g. after transportation), do not switch it on immediately. Let the device reach room temperature before switching it on, otherwise it may be damaged by the formed condensation. -
Page 10: Description Of The Device
Description of the Device The Showtec Pixelbar 16 Q6 is a LED bar with 16 x 6-in-1 RGBWA-UV LEDs. It is suitable for indoor venues. The different mounting positions allow for various creative setups. With Pixelbar 16 Q6 it is possible to create both saturated and pastel colors. -
Page 11: Product Specifications
Pixelbar 16 Q6 Product Specifications Model: Pixelbar 16 Q6 Electrical: Input voltage: 100–240 V AC, 50/60 Hz Power consumption: 170 W Fuse: T3A, 110-250 V, 50/60 Hz Physical: Dimensions: 1047 x 135 x 176 mm (L x W x H)(with installed 2 mounting brackets) -
Page 12: Dimensions
Pixelbar 16 Q6 Dimensions Fig. 04 Fig. 05 Product code: 41308... -
Page 13: Installation
Pixelbar 16 Q6 Installation Safety Instructions for Installation WARNING Incorrect installation can cause serious injuries and damage of property. If trussing systems are used, installation must be carried out only by instructed or skilled persons. Follow all applicable European, national and local safety regulations concerning rigging and trussing. - Page 14 Pixelbar 16 Q6 CAUTION Restrict the access under the work area during rigging and/or derigging. To mount the device, follow the steps below: Install the 2 mounting brackets (03) for option 1, or 1 mounting bracket (03) for option 2.
-
Page 15: Angle Adjustment
Pixelbar 16 Q6 Angle Adjustment You can adjust the angle of the device with the adjustment screws (02). 01) Turn the adjustment screws (02) counterclockwise to release them. Tilt the device at the desired angle (see Fig. 08). Turn the adjustment screws (02) clockwise to tighten them. Make sure that the device cannot move freely after the adjustment screws (02) are tightened. -
Page 16: Power Linking Of Multiple Devices
Do not link more devices on one power link than the maximum recommended number. Maximum recommended number of devices: ● at 100–120 V: 8 devices Pixelbar 16 Q6 ● at 200–240 V: 15 devices Pixelbar 16 Q6 Product code: 41308... -
Page 17: Setup
Disconnect power supply before connecting or disconnecting data cables. Stand-alone Setup When the Pixelbar 16 Q6 is not connected to a controller or to other devices, it functions as a stand-alone device. It can be operated manually or in auto mode. -
Page 18: Dmx Cables
Fig. 09. Fig. 09 Master/Slave Setup The Pixelbar 16 Q6 supports master/slave control mode. To connect multiple devices in master/slave setup, follow the steps below: Connect the first device’s DMX OUT connector to the second device’s DMX IN connector with a 3-pin/5-pin DMX cable. -
Page 19: Dmx Linking
Continue assigning the starting addresses of the remaining devices by adding each time 12 to the previous number. Make sure that you do not have any overlapping channels in order to control each Pixelbar 16 Q6 correctly. If two or more devices are addressed similarly, they will work similarly. -
Page 20: Ethernet Connection
Pixelbar 16 Q6 Ethernet Connection Attention Connect all data cables before supplying power. Disconnect power supply before connecting or disconnecting data cables. Art-Net, sACN, and Kling-Net Protocols Art-Net is a protocol that uses TCP/IP to transfer large amount of DMX-512 data over an Ethernet network. -
Page 21: Art-Net/Sacn/Kling-Net Setup
Pixelbar 16 Q6 Art-Net/sACN/Kling-Net Setup The Pixelbar 16 Q6 has 2 RJ45 connectors. Either connector can be used as an input and as throughput. To connect multiple devices in an Art-Net/sACN/Kling-Net setup, follow the steps below: Use a CAT-5/CAT-5E/CAT-6 cable to connect the RJ45 connector of the computer/lighting controller to one of the RJ45 connectors of the first device. -
Page 22: Universe Numbering
(0–15) 32766 32767 Make sure that you do not have any overlapping channels in order to control each Pixelbar 16 Q6 correctly. If two or more devices are addressed similarly, they will work similarly. Note: If you are using an Art-Net controller that supports Art-Net I or Art-Net II, the Art-Net net must be set to 0. -
Page 23: Operation
Before connecting the device to the power supply, make sure that the current, voltage and frequency match the input voltage, current and frequency specified on the information label on the device. Control Modes The Pixelbar 16 Q6 supports the following control modes: ● Stand-alone: Auto operation mode (built-in chases), manual operation ●... -
Page 24: Control Panel
● Press the power switch (10) in OFF position to turn the device off. Upon start-up the display will show a splash screen with the logo of Showtec followed by the name of the device: Immediately afterwards the display will show the start screen. The start screen provides information about... - Page 25 Pixelbar 16 Q6 Press the UP/DOWN buttons to see the second part of the start screen: This screen provides information about the current IP address of the device. Note: If no button is pressed, after 20 seconds of inactivity the display will return to the start screen and after 10 more seconds it will turn off.
-
Page 26: Menu Overview
Pixelbar 16 Q6 Menu Overview Product code: 41308... - Page 27 Pixelbar 16 Q6 Product code: 41308...
-
Page 28: Main Menu Options
Pixelbar 16 Q6 Main Menu Options The main menu has the following options: Press the UP/DOWN buttons to navigate through the main menu. 02) Press the ENTER button to open the submenus. Product code: 41308... -
Page 29: Dmx Address
Pixelbar 16 Q6 DMX Address In this menu you can set the DMX starting address of the device. 01) Press the UP/DOWN buttons to move the cursor respectively to the right/left on the display. 02) Press the ENTER button to confirm the selection. The selection will be highlighted. -
Page 30: Set Dimmer Curve
Pixelbar 16 Q6 Set Dimmer Curve In this menu you can set the dimmer curve. 01) Press the UP/DOWN buttons to select one of the following 3 options: ● Linear ● S Curve ● Square 02) Press the ENTER button to confirm the selection. -
Page 31: Slave Mode
Pixelbar 16 Q6 Slave Mode In this menu you can activate master/slave control mode. 01) Press the UP/DOWN buttons to select one of the following 2 options: ● Master: The device will operate as a master device in master/slave mode ●... -
Page 32: Set Netmask
Pixelbar 16 Q6 Set Netmask If you have selected DHCP IP or KlingNet IP in 6.6.8. Set IP Mode above, when you select Set Netmask in the menu, the display will show respectively the following: The Netmask of the IP address of the device will be generated automatically by the network server. - Page 33 Pixelbar 16 Q6 Decimal to Hexadecimal Conversion Table Product code: 41308...
-
Page 34: Set Lcd Backlight
Pixelbar 16 Q6 Set LCD Backlight In this menu you can select whether the backlight of the display will remain on or will turn off after 30 seconds of inactivity. 01) Press the UP/DOWN buttons to toggle between ON and OFF: ●... -
Page 35: Auto Test
Pixelbar 16 Q6 Auto Test In this menu you can perform a test of the device’s parameters. Press the ENTER button to confirm and start the test. During the test the display will show: Press the ENTER button to stop the test. -
Page 36: Dmx Channels
Pixelbar 16 Q6 DMX Channels 6 Channels, 8 Channels, 12 Channels 6 CH 8 CH 12 CH Function Value Setting Master Dimmer 000–255 From low to high intensity (0–100 %) 000–255 From low to high intensity (0–100 %) Green 000–255 From low to high intensity (0–100 %) -
Page 37: 96 Channels, 101 Channels
Pixelbar 16 Q6 96 Channels, 101 Channels Fig. 15 96 CH 101 CH Function Value Setting Red 1 000–255 From low to high intensity (0–100 %) Green 1 000–255 From low to high intensity (0–100 %) Blue 1 000–255 From low to high intensity (0–100 %) Amber 1 000–255... - Page 38 Pixelbar 16 Q6 96 CH 101 CH Function Value Setting Green 8 000–255 From low to high intensity (0–100 %) Blue 8 000–255 From low to high intensity (0–100 %) Amber 8 000–255 From low to high intensity (0–100 %) White 8 000–255...
-
Page 39: Hsi, Hsv
Pixelbar 16 Q6 96 CH 101 CH Function Value Setting 000–010 No function 011–029 Auto 0 030–048 Auto 1 049–067 Auto 2 068–086 Auto 3 087–105 Auto 4 106–124 Auto 5 Auto Programs 125–143 Auto 6 144–162 Auto 7 163–181 Auto 8 182–200... -
Page 40: Troubleshooting
Pixelbar 16 Q6 Troubleshooting This troubleshooting guide contains solutions to problems which can be carried out by an ordinary person. The device does not contain user-serviceable parts. Unauthorized modifications to the device will render the warranty void. Such modifications may result in injuries and material damage. -
Page 41: Maintenance
Pixelbar 16 Q6 Maintenance Safety Instructions for Maintenance DANGER Electric shock caused by dangerous voltage inside Disconnect power supply before servicing or cleaning. WARNING Risk of burns due to hot surface Allow the device to cool down for at least 15 minutes before servicing or cleaning. -
Page 42: Basic Cleaning Instructions
Pixelbar 16 Q6 Basic Cleaning Instructions The external lens of the device must be cleaned periodically in order to optimize the light output. The cleaning schedule depends on the conditions at the site where the device is installed. When smoke or fog machines are used at the site, the device will need more frequent cleaning. -
Page 43: Deinstallation, Transportation And Storage
Pixelbar 16 Q6 Deinstallation, Transportation and Storage Instructions for Deinstallation WARNING Incorrect deinstallation can cause serious injuries and damage of property. ● Let the device cool down before dismounting. ● Disconnect power supply before deinstallation. ● Always observe the national and site-specific regulations during deinstallation and derigging of the device. - Page 44 ©2020 Showtec...
Need help?
Do you have a question about the Pixelbar 16 Q6 and is the answer not in the manual?
Questions and answers