Advertisement
Quick Links
Hallingford - 2 Door Sliding Robe
Assembly Instructions
Important
– Please read these instructions fully before starting assembly
If you need help or have damaged or missing parts, call the Customer Helpline: 0845 6400800
DR89954
- Please keep for future reference
Dimensions
Width - 100,5cm
Depth - 60,3cm
Height -205,7cm
Tip : To prevent damage,
we recommend that you
build your unit on the
carton(s) it was packed in.
305/2811
305/2859
305/2842
305/2828
305/2835
Issue1 - 12/05/2013
Advertisement
Related Manuals for Argos Hallingford 305/2811
Summary of Contents for Argos Hallingford 305/2811
- Page 1 Hallingford - 2 Door Sliding Robe Assembly Instructions 305/2811 - Please keep for future reference 305/2859 305/2842 305/2828 305/2835 Tip : To prevent damage, we recommend that you build your unit on the carton(s) it was packed in. Dimensions Width - 100,5cm Depth - 60,3cm Height -205,7cm Important...
- Page 2 Safety and Care Advice Important – Please read these instructions fully before starting assembly • Check you have all the • Do not stand or put weight on • We do not components and tools listed on the product, this could cause recommend the pages 2 and 3.
- Page 3 Components - Panels Please check you have all the panels listed below Slide door Left side Right side Mirror slide door (205.6 x 58cm) (196.3 x 50cm) (205.6 x 58cm) (196.3 x 50cm) P2350 P2350 P3530 PS3529 Large horizontal Bottom (96.7 x 46.7cm) (96.7 x 55.7cm) (96.7 x 55.7cm)
- Page 4 Components - Fittings If you have damaged or missing components, call the Customer Helpline: 0845 6400800 Please check you hav tings listed below Note: The quantities below are the correct amount to complete the assembly. In some cases more FK1324 FK1051 FK1056 Chipboardscrew x 10...
- Page 5 Step 1 Attach hanger rail support using 12.5mm screw onto sides Note: Two pannels Screw twister leg into sides Note: twister leg as far as shown. Do not over tighten. Step 2 Attaching plinths Align the sides of plinth front with bottom shown and attach using chipboardscrew...
- Page 6 Assembly Instructions Step 3 Insert expando housings into top Flip panel Carefully knock sliding rail into top by using a hammer. Reapeat b for bottom...
- Page 7 Assembly Instructions Step 4 Attaching panel Position top , bottom and horizontal Insert twister cam into panels 5/6/7 where shown. Usa a screwdriver to turn twister cam clockwise to lock. Step 5 Repeat Step 4 for the second side Insert the Cam so the Use a Flat Bladed Locate the 'mating' The final 'locked' position will...
- Page 8 Assembly Instructions Step 6 Fitting back panel Important! Cabinet MUST A:A = B:B be ‘square’ before back is attached. Attach foldy back back of wardrobe with the coloured surface facing the inside of the unit using nails Nails should be spaced about 150mm apart.
- Page 9 Assembly Instructions Step 7 Align the unit Stand up the unit Use a spirit level to check if the base of this unit is level front-to-back , side-to-side and top-to-bottom in the three positions shown. Use pegs to level your unit in all three direction shown.
-
Page 10: Glass Handle With Care
Assembly Instructions GLASS handle with care Step 8 Insert hanger rail Place hanger rail onto hanger rail supports Step 9 Fitting handle to mirrordoor Hold hande mouldings against front of mirror slide door , make sure the ends mirror slide door Screw screws into the ‘V’... - Page 11 Assembly Instructions GLASS handle with care Step 10 Stick felts onto mirror slide door where shown. Insert Sliding door roller in mirror slide door the handle mouldings Insert sliding door roller adjustables in slide door them with backpannelscrews Insert sliding door guides on the other end of the mirror slide door Step 11...
- Page 12 Assembly Instructions Step 13 Fitting of the doors To fit the bottom of the Doors Important! Double check if the unit is level before this is not the case This lug fits into This lug fits into please go back to the groove in the groove in the track...
- Page 13 Assembly Instructions Step 16 Attaching pelmet Position the pelmet above the unit drilling-holes and turn the screws as far as they will go. Step 17 Attaching L-bracket Position L-Bracket onto top 15mm screw Note: there are no pre-drilled holes for 15mm screw please see last page for more information.
- Page 14 Assembly Instructions Step 18 Attaching door-stops Stick 2 door-stops onto the outside edge of each plain door to act as and side panels.
- Page 15 Assembly Instructions If your doors do not run smoothly Level & square the unit Level & square the unit up: Knock the pegs as far as you require, under the ends of the unit and then snap off flush with the panel. For more detailed information see step 12.
-
Page 16: A Guide To - Wall Mounting & Fixings
A Guide to - Wall Mounting & Fixings Important: When drilling into walls always Important note: check that there are no hidden wires or pipes etc. If plastic wall plugs Make sure that the screws and wall plugs being used are supplied with your are suitable for supporting your unit.
Need help?
Do you have a question about the Hallingford 305/2811 and is the answer not in the manual?
Questions and answers