Sealey SA654.V3 Instructions

thank you for purchasing a Sealey product. Manufactured to a high standard, this product
will, if used according to these instructions, and properly maintained, give you years of
trouble free performance.
IMPORTANT: PLEASE rEAd tHESE inStructionS cArEfuLLy. notE tHE SAfE oPErAtionAL
rEQuirEMEntS, WArninGS & cAutionS. uSE tHE Product corrEctLy And WitH cArE
for tHE PurPoSE for WHicH it iS intEndEd. fAiLurE to do So MAy cAuSE dAMAGE
And/or PErSonAL inJury And WiLL inVALidAtE tHE WArrAnty. KEEP tHESE inStructionS
SAfE for futurE uSE.
1. SAfEty
 Follow all workshop Health & Safety rules, regulations and conditions when using tool.
 WArninG! Disconnect from air supply before changing grinding bit or servicing.
 Maintain die grinder in good condition and replace any damaged or worn parts. Use
genuine parts only. Unauthorised parts may be dangerous and will invalidate the warranty.
 WArninG! Check correct air pressure is maintained and not exceeded. We recommended 90psi.
 Keep air hose away from heat, oil and sharp edges. Check air hose for wear before each use and ensure
that all connections are secure.
 WArninG! Before each use check grinding bit is secure, and the bit is not worn or damaged. If damaged,
replace immediately.
 Ensure replacement grinding bits are not damaged (cracks, deformations or splinters etc).
 Always use the correct grinding bit suitable for the material being ground. Ensure the maximum
speed specification of the bit is higher than that indicated on the machine data plate.
 WArninG! Always wear approved eye or face protection when operating the die grinder.
 Use breathing protection in accordance with COSHH regulations if fumes or dust pose a hazard. Wear ear
defenders and gloves if necessary.
 Keep hands and body clear of the workpiece when operating the die grinder.
 Maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip shoes.
 Secure unstable workpiece with a clamp, vice or other adequate holding device.
 Keep children and non essential persons away from the working area.
 Avoid subjecting grinding bit to excessive strain, always ease grinding bit against workpiece
(a harsh impact may break the bit). Maintain a controlled progression.
 do not hold the workpiece by hand. Use clamps or a vice to secure the workpiece.
 do not use the die grinder for a task it is not designed to perform.
 WArninG! do not use die grinder if damaged or faulty. Contact your local service agent.
 do not use die grinder unless you have been instructed in its use by a qualified person.
 do not carry the die grinder by the air hose, or yank the hose from the air supply.
 do not direct air from the air hose at yourself or others.
 WArninG! do not grind any materials containing asbestos.
 do not turn the die grinder on whilst the grinding bit is in contact with the workpiece.
 do not use die grinder where there are flammable liquids, solids or gases such as paint solvents,
including waste wiping or cleaning rags etc as generated sparks may be dangerous.
 do not touch the workpiece close to the ground surface as it will be very hot. Allow to cool.
The workpiece may also be very sharp.
 do not operate die grinder if you are tired, under the influence of alcohol, drugs or intoxicating medication.
 When not in use disconnect from air supply and store in a safe, dry, childproof location.
2. introduction
Composite cover moulded around lightweight aluminium alloy housing reduces effects of chill on operator's
hands and provides added control. Air motor with quality bearings for smooth and powerful operation. Exhaust
outlet adjusts 360° keeping air flow away from operator. Safety trigger prevents inadvertent operation. Ideal for
re-shaping, deburring and smoothing off rough edges on castings. Suitable for the professional workshop.
© Jack Sealey Limited
INSTRUCTIONS FOR:
Air diE GrindEr MAXi SiZE
StrAiGHt
SA654.V3
MODEL No:
Original Language Version
SA654.V3 Issue: 2(SP) - 15/07/14