Advertisement
Blade orientation and direction of rotation.
direction of
rotation mark
Blade fixing bolt (RH thread)
4. OPERATION
NOTE: this appliance is not intended for use by persons (including
children) with reduced physical, sensory or mental capabilities or lack
of experience and knowledge, unless they have been given
supervision or instruction concerning the use of the appliance by a
person responsible for their safety. children should be supervised to
ensure that they do not play with the appliance.
4.1
With the instructions to this stage read and the mower
assembled, plug the mains cable into an rcd protected and
isolated 230V Ac supply.
4.2
With the mower cutter face down on the lawn to be cut, switch
on the supply. nothing will happen until the safety (inhibit)
button has been depressed and the power lever gripped.
4.3
now positioned at the mower handle and the cable clear of the
cutter deck, using the tubular handle frame, tip the whole
mower approximately 10° raising the cutter blade off the lawn.
depress the safety button with one hand and hold, nothing will
happen until the power lever is gripped with the other hand.
4.4
With the motor running at full speed release the safety button,
maintaining grip on the power lever and lower the blade on to
the lawn.
4.5
release grip on power lever to stop the motor. the blade
will rotate for a few seconds after the motor has stopped.
mowing tip-: to prevent accidentally running over the lead with
cutter deck, trail the mains lead over one shoulder and hold
with the hand of the other shoulder. Alternate with operating
mower with both hands, always keeping the lead on your
shoulder.
fig.4
cutting depth adjustment.
fig.6
lift spring loaded hinged stone
guard panel to fit grassbox.
(2 tabs along top of opening)
© Jack sealey limited 2013
5.1
5.2
5.3
5.4
5.5
5.6
5.6.1
5.6.2 Clear any accumulated grass cuttings from the airway flutes
fig.3
5.6.3 Clean any grass cuttings from the flying lead.
5.6.4
6.1
6.1.1
6.1.2
6.1.3
6.2
6.2.1
6.2.2
6.2.3
6.2.4
6.3
6.3.1
6.3.2 Check that blade is fitted correctly.
6.3.3
6.3.4
fig.5
Grassbox location notches.
(employ either way up)
fig.7
Original Language Version
5. MAINTENANCE
Ensure all fixings are tight and secure.
replace any damaged or worn parts immediately.
check blade during and after each use, see section
3.3.2. for removal.
check cable clips and cable runs, especially the strain relief
hook loop, mains plug and switch connections .
there are no customer serviceable parts other than the
blades and frame fixings, use qualified service personnel for
all other aspects of maintenance.
Cleaning
After each use, with mower power unplugged from mains
supply, clear accumulated grass cuttings from inside cutter
deck. DO NOT allow the grass to dry on the mower.
in blade hub impellor.
clean the mower externally before storing with special
attention to grass box slots, which could affect airflow and
grass collection rate.
6.
TROUBLESHOOTING
Mower fails to operate
check that the power is on.
check that the start up procedure has been followed, safety
button pressed and power lever operated. see section 4.
check the 5amp fuse in the plug. If blown, replace. If it
continues to blow, the mower must be checked by a qualified
electrician.
Poor grass collection.
disconnect from the mains electricity supply.
clean the outside of the air intakes, the discharge chute and
the underside of the deck, see fig.3.
clear grass box slots of solids.
motor not running full speed with no load. this can only be
checked by qualified personnel, consult your Sealey Dealer.
Excessive vibration.
disconnect from mains supply.
damaged blade, replace.
If excessive vibration persists, discontinue use and seek
advice from your sealey dealer.
Gl54
Issue no: 1 - 15/01/13
Advertisement
