CommScope PFU-P-C-O-060-02 Hardware Manual

CommScope PFU-P-C-O-060-02 Hardware Manual

1 and 2 port 60w poe extenders and power extender
Hide thumbs Also See for PFU-P-C-O-060-02:

Advertisement

1 and 2 Port 60W POE Extenders
and Power Extender
Hardware Manual
TC-96231-IP Rev C
June 2019
860634349 Rev C

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the PFU-P-C-O-060-02 and is the answer not in the manual?

Questions and answers

Summary of Contents for CommScope PFU-P-C-O-060-02

  • Page 1 1 and 2 Port 60W POE Extenders and Power Extender Hardware Manual TC-96231-IP Rev C June 2019 860634349 Rev C...
  • Page 3: Table Of Contents

    Powered Fiber Cable Installation .................. 18 DC Power Cable Installation ..................23 Sealing the Unit......................23 Mounting the Unit......................24 Solar Shield........................26 4 Detailed Specifications............... 27 Copyright, Trademarks and Commercial Disclaimer ............ 31 This product is copyright © 2019 CommScope, LLC. All Rights Reserved.
  • Page 4 PoE Extender Hardware Manual This product is copyright © 2019 CommScope, LLC. All Rights Reserved.
  • Page 5: Safety Notice

    Reliable earthing of rack-mounted equipment should be maintained. Particular attention should be given to supply connections other than direct connections to the branch circuit (e.g. use of power strips). This product is copyright © 2019 CommScope, LLC. All Rights Reserved.
  • Page 6 Ultimate disposal of this equipment must be carried out according to relevant national laws. The equipment should be installed by suitably trained personnel, and installation should follow good working practice. This product is copyright © 2019 CommScope, LLC. All Rights Reserved.
  • Page 7: Consigne De Sécurité

    Il convient de maintenir une mise à la terre fiable d'équipement monté en rack. Il convient de faire particulièrement attention aux raccordements d'alimentation autres que ceux directement en contact avec le circuit de dérivation (p. ex., utiliser des bars d'alimentation). This product is copyright © 2019 CommScope, LLC. All Rights Reserved.
  • Page 8 La suppression définitive de cet équipement devra être effectuée conformément aux lois nationales pertinentes. L'équipement doit être installé par du personnel parfaitement qualifié, et l'installation devra être conforme aux bonnes pratiques. This product is copyright © 2019 CommScope, LLC. All Rights Reserved.
  • Page 9: Sicherheitshinweis

    Typenschildern, um die Gesamtlast zu ermitteln. Es muss eine zuverlässige Erdung der Rack-Geräte gegeben sein. Besondere Aufmerksamkeit gilt dabei der indirekten Anbindung an Zweigstromkreise (z. B. Verwendung von Mehrfachsteckerleisten). This product is copyright © 2019 CommScope, LLC. All Rights Reserved.
  • Page 10 Die Entsorgung dieses Geräts muss nach den einschlägigen nationalen Rechtsvorschriften erfolgen. Das Gerät muss durch entsprechend geschultes Personal installiert werden. Bei der Installation ist auf gute Arbeitspraxis zu achten. This product is copyright © 2019 CommScope, LLC. All Rights Reserved.
  • Page 11: Ce Notice

    If the unit is found to be defective, please contact Technical Support via http:// www.commscope.com/SupportCenter WEEE Instructions for recycling of items at end of life can be found at www.CommScope.com by searching for 'WEEE'. At time of printing this is http://www.commscope.com/About-Us/Corporate-Responsibilityand-Sustainability/Environment/ Recycling/ where information for customers and recyclers is available.
  • Page 12 PoE Extender Hardware Manual This product is copyright © 2019 CommScope, LLC. All Rights Reserved.
  • Page 13: Introduction

    Circuit protection electronics Optical to electrical Media Conversion When coupled with any standard NEC Class 2 48V DC power supply, CommScope's Powered Fiber Cable system can power and communicate with PoE standard devices at far greater distances than "category style" copper cabling systems (typically limited to 90 meters) while still meeting NEC Class 2 and SELV standards, eliminating the need for qualified electricians during installation.
  • Page 14: Why Protect Remotely Powered Circuits

    High power inductors used as coordinating elements to maximize energy efficiency • Enhanced PoE port protection compliant with more stringent ITU K.45 2016 requirements • Sealed enclosure for environmental protection • This product is copyright © 2019 CommScope, LLC. All Rights Reserved.
  • Page 15: Package Contents

    12 AWG or 2mm diameter wire stripper for 12 AWG cable • 16 AWG or 1.2mm wire diameter stripper for the 16 AWG cable • Fastenings for wall or pole mounting • This product is copyright © 2019 CommScope, LLC. All Rights Reserved.
  • Page 16 PoE Extender Hardware Manual This product is copyright © 2019 CommScope, LLC. All Rights Reserved.
  • Page 17: Installation

    Unscrew the caps and then remove the grommets from all of the pass-through connectors. Note 1: Do not unscrew the pass-throughs from metal body of the extender. These have been factory fitted and sealed to the correct torque setting. This product is copyright © 2019 CommScope, LLC. All Rights Reserved.
  • Page 18 PoE Extender Hardware Manual This product is copyright © 2019 CommScope, LLC. All Rights Reserved.
  • Page 19: Sfp Configuration

    TOP SFP: 100 Mbits/s BOTTOM SFP: 1 Gbit/s BOTTOM SFP: 100 Mbit/s Replace the fiber splice tray, apply Locite 222 to all screws before fitting. Ensure all screws are filled (see below). This product is copyright © 2019 CommScope, LLC. All Rights Reserved.
  • Page 20: Ethernet Cables Installation

    Before tightening the seal cap, insert the RJ45 plug into the jack with the lock tab facing This product is copyright © 2019 CommScope, LLC. All Rights Reserved.
  • Page 21 PoE Extender Hardware Manual Tighten the cap against the pass through. The recommended torque is 2.50Nm (22.1in lbf). If applicable, repeat steps 1-3 for the second PoE connection. This product is copyright © 2019 CommScope, LLC. All Rights Reserved.
  • Page 22: Powered Fiber Cable Installation

    PoE Extender Hardware Manual Powered Fiber Cable Installation The CommScope Powered Fiber Cable consists of 2 insulated copper power conductors and a central tube containing the optical fiber. Separate the three cores to allow the power to be connected to the screw terminals, and the fiber thread to be connected to a fiber terminal, which is then inserted into the SFP.
  • Page 23 Use tape or heat shrink to prevent the cables splitting further than the required length. Ensure the cables are smooth to prevent water ingress issues through the grommet. Strip the two copper elements to an appropriate length, just as accessing any copper cable. This product is copyright © 2019 CommScope, LLC. All Rights Reserved.
  • Page 24 Use tape or heat shrink to prevent the cables splitting further than the required length. Thread the two cables in to the power connectors and tighten the screws. Note: Due to the cross-polarity protection, the circuit will work regardless of the input polarity. This product is copyright © 2019 CommScope, LLC. All Rights Reserved.
  • Page 25 The fibers should wrap around the splice tray several times to allow for future resplicing. The splice to the fiber connectors should sit in the splice island in the tray as below. This product is copyright © 2019 CommScope, LLC. All Rights Reserved.
  • Page 26 The fiber LC/UPC pigtails should wrap around the splice tray once, then connect to the SFPs as below. Note: Field installable connectors such as LightCrimp Plus can be used. A clip to connect two LC simplex to one LC duplex is recommended. This product is copyright © 2019 CommScope, LLC. All Rights Reserved.
  • Page 27: Dc Power Cable Installation

    Ensure the supplied seal ring is properly seated in its channel (it only fits in one orienta- tion) and that all cables are secured. Apply Loctite 222 to all lid bolts. Put the lid back in place. This product is copyright © 2019 CommScope, LLC. All Rights Reserved.
  • Page 28: Mounting The Unit

    Mounting the Unit Wall Mount The PoE extender has 4 holes on the exterior of the device for attaching to a wall or flat surface This product is copyright © 2019 CommScope, LLC. All Rights Reserved.
  • Page 29 The four slots in the raised sections on the bottom of the device may be used for pole attachment using band clamps (jubilee clips). PoE pole mounted with solar shield This product is copyright © 2019 CommScope, LLC. All Rights Reserved.
  • Page 30: Solar Shield

    At the top of the Two Port PoE Extender's operating temperature range, the physical temperature of the PoE Extender may exceed 70ºC. Ensure the supplied solar shield is in place for protection. See Table 4.2 on page 29 for operating temperature details. This product is copyright © 2019 CommScope, LLC. All Rights Reserved.
  • Page 31: Detailed Specifications

    C to +65 65°C assumes 45°C ambient air temperature, plus 20°C sun loading. Table 4.3: Physical Dimensions Item Specification Dimensions including solar shield 283mm x 225mm x 77mm Weight 3.8kg This product is copyright © 2019 CommScope, LLC. All Rights Reserved.
  • Page 32 (CLASS 0 OR 3) (CLASS 4) 15.4W 15.4W (CLASS 0 OR 3) (CLASS 0 OR 3) 15.4W (CLASS 0 OR 3) High PoE (Dual Class 4) Note 1: Single-port PoE Extender only This product is copyright © 2019 CommScope, LLC. All Rights Reserved.
  • Page 33 Accepts all MSA compliant 100Base-X and 1000Base-X SFP transceivers Optical Input Singlemode ITU-T G657.A2 Optical Input 50um Multimode OM3 or OM4 RJ45 Connector Output Half and Full Duplex Modes Supported. 10/100/1000Mb Ethernet This product is copyright © 2019 CommScope, LLC. All Rights Reserved.
  • Page 34 PFC,Singlemode,4F,I/O,16AWG PFC-S04O12 PFC,Singlemode,4F,Outdoor,12AWG PFC-S04O16 PFC,Singlemode,4F,Outdoor,16AWG PFC-S12L12 PFC,Singlemode,12F,I/O,12AWG PFC-S12L16 PFC,Singlemode,12F,I/O,16AWG PFC-S12O12 PFC,Singlemode,12F,Outdoor,12AWG PFC-S12O16 PFC,Singlemode,12F,Outdoor,16AWG PFC-302L12 PFC,OM3,2F,I/O,12AWG PFC-302L16 PFC,OM3,2F,I/O,16AWG PFC-302O12 PFC,OM3,2F,Outdoor,12AWG PFC-302O16 PFC,OM3,2F,Outdoor,16AWG PFC-304L12 PFC,OM3,4F,I/O,12AWG PFC-304L16 PFC,OM3,4F,I/O,16AWG PFC-304O12 PFC,OM3,4F,Outdoor,12AWG PFC-304O16 PFC,OM3,4F,Outdoor,16AWG This product is copyright © 2019 CommScope, LLC. All Rights Reserved.
  • Page 35: Copyright, Trademarks And Commercial Disclaimer

    PoE Extender Hardware Manual Copyright, Trademarks and Commercial Disclaimer To find out more about CommScope® products, visit us on the web at www.commscope.com All trademarks identified by ® or ™ are registered trademarks or trademarks, respectively, of CommScope, Inc. © 2019 Commscope, Inc All Rights Reserved This product is covered by one or more U.S.
  • Page 36 PoE Extender Hardware Manual This product is copyright © 2019 CommScope, LLC. All Rights Reserved.

This manual is also suitable for:

Pfu-12-c-o-060-01Pfu-p-c-o-060-01Pfu-48-c-o-060-01

Table of Contents