Related Manuals for Denver WCS-5020
Summary of Contents for Denver WCS-5020
- Page 1 Infrared Trail Camera User's Manual WCS-5020 Package List: Camera USB Cable Mounting Strap User Manual...
-
Page 2: Parts Of The Camera
Parts Of The Camera 1. Display screen 2. IR lamps 3. Lens 4. Up/Video Button... - Page 3 5. Down/Capture Button 6. Motion sensor 7. OK/Shot button 8. Menu Button 9. Right button 10. Playback button 11. DC adapter port 12. Tripod Slot 13. Micro SD card slot...
-
Page 4: Power Supply
13. Battery compartment 14. ON-TEST-OFF button 15. USB jack Power Supply Please install batteries before using the camera. Unlock the camera and you will find the battery compartment. Install 4 pieces of 1.5V AA batteries. Please make sure the battery polarity is correct. Inserting the Memory Card •... -
Page 5: Basic Operation
• To avoid malfunction, the memory card should be far away from water, strong vibration, dust, hot source and direct sunlight. • Do not insert the memory card forcibly. Please refer to the marking on the camera. • For the first time of use, please wait for the memory card temperature reach the ambient temperature. -
Page 6: System Setup
System Setup Switch Mode Button to “Test”, then you can set the system parameters. Press Menu button to open the setup menu. Press Up/Down button to scan all menus. Then press OK button to enter the options interface. Press Up/Down button to scan all options. And press OK button to confirm options. - Page 7 Photo Series Set the photo number of continuous shootings. In photo mode, the camera will take photos continuously. Options: [1 photo]/[2 photos in series]/[3 photos in series]. Video Resolution Set the video resolution. The larger the resolution is, the longer the video time will be stored. Options: [1920x1080P]/[1280x720P]/[720x480P]/[640x480P]/ [320x240P].
- Page 8 Shot Lag Set the time of delay shooting when the camera detects a motion. In the selected time, the camera will not record any image or video. This function can avoid storing too many same events and waste of memory. Options: 5 seconds~60 minutes.
- Page 9 Target Recording Time Set the target recording time. As shown in below picture, you can set the start and stop time. The camera will work just in the stated time slot. In other time, the camera will keep in standby state.
- Page 10 works for 24 hours, there will be 24 photos. These photos will be converted into a video. [Off]: Close the time-lapse function. Language Set the language display on screen. Options: [English]/[German]/[Danish]/[Finnish]/[Swedish] [Spanish]/[French]/[Italian]/[Dutch]/[Portuguese]/[Simplified Chinese]/[Japanese]. Endless Capture Set the camera to record video in loop. Options: [On]/[Off].
-
Page 11: Time And Date
Time & Date Set the date and time of camera. Press Right button to choose an item and press Up / Down button to adjust the value. And then press OK button to confirm. • Options of date format: dd/mm/yyyy, yyyy/mm/dd, mm/dd/yyyy. -
Page 12: Format Memory Card
Beep Sound Open/close the touch-tone. Options: [On]/[Off]. Format Memory Card Formatting the memory card will delete all data permanently. Before using a new memory card or a card that has been used in another device previously, please format the memory card. Options: [Yes]/[No]. - Page 13 Take Photos, Record Videos, Playback Switch the Mode Button to “Test”. In this mode, you can take photos, record videos and playback files manually. • Take Photos: Press Capture button to switch to photo mode. Press Shot button to take a picture. •...
-
Page 14: Working Mode
Working Mode Switch the Mode Button to “On”. After turning on the camera, the screen will display 15 seconds countdown. Then the LEDs and screen will go out. The camera begins to operate independently and enter standby mode. • If the wild animals enter the detection range of the motion sensors, the camera will be activated and detect the motion trail. - Page 15 Using a Card Reader 1. Pop-up the memory card from the camera and insert it into a card reader. Then connect the card reader to a computer. 2. Open [My Computer] or [Windows Explorer] and double- click the removable disk icon that represents the memory card.
- Page 16 We take reservations for errors and omissions in the manual. ALL RIGHTS RESERVED, COPYRIGHT DENVER ELECTRONICS A/S Electric and electronic equipment and included batteries contains materials, components and substances that can be hazardous to your health and...
- Page 17 Additional information is available at the technical department of your city. Hereby, Inter Sales A/S declares that the radio equipment type WCS-5020 is in compliance with...
- Page 18 ICON on topline of website. Write model number: WCS-5020. Now enter product page, and red directive is found under downloads/other downloads. DENVER ELECTRONICS A/S Omega 5A, Soeften...
Need help?
Do you have a question about the WCS-5020 and is the answer not in the manual?
Questions and answers