Table of Contents
Advertisement
Owner's Manual & Safety Instructions
Save This Manual
inspection, maintenance and cleaning procedures. Write the product's serial number in the back of the manual
near the assembly diagram (or month and year of purchase if product has no number).
Keep this manual and the receipt in a safe and dry place for future reference.
ORBITAL
(Blade sold separately)
Email our technical support at: productsupport@harborfreight.com
REV 14g
When unpacking, make sure that the product is intact
and undamaged. If any parts are missing or broken,
please call 1-888-866-5797 as soon as possible.
©
Copyright
2014 by Harbor Freight Tools
No portion of this manual or any artwork contained herein may be reproduced in
any shape or form without the express written consent of Harbor Freight Tools.
Diagrams within this manual may not be drawn proportionally. Due to continuing
improvements, actual product may differ slightly from the product
described herein. Tools required for assembly and service may not be included.
Keep this manual for the safety warnings and precautions, assembly, operating,
Visit our website at: http://www.harborfreight.com
®
. All rights reserved.
Read this material before using this product.
Failure to do so can result in serious injury.
SAVE THIS MANUAL.
Advertisement
Table of Contents
Related Manuals for Chicago Electric 62422
Summary of Contents for Chicago Electric 62422
- Page 1 Owner’s Manual & Safety Instructions Save This Manual Keep this manual for the safety warnings and precautions, assembly, operating, inspection, maintenance and cleaning procedures. Write the product’s serial number in the back of the manual near the assembly diagram (or month and year of purchase if product has no number). Keep this manual and the receipt in a safe and dry place for future reference.
-
Page 2: General Power Tool Safety Warnings
Save all warnings and instructions for future reference. The term ″power tool″ in the warnings refers to your mains‑operated (corded) power tool. For technical questions, please call 1-888-866-5797. Page 2 Item 62422... - Page 3 Eye protection must be This will ensure that the safety of ANSI‑approved and breathing protection the power tool is maintained. must be NIOSH‑approved for the specific hazards in the work area. For technical questions, please call 1-888-866-5797. Item 62422 Page 3...
-
Page 4: Jigsaw Safety Warnings
• Properly maintain and inspect to avoid electrical shock. • Any power cord must be properly grounded. Ground Fault Circuit Interrupter (GFCI) should also be implemented – it prevents sustained electrical shock. For technical questions, please call 1-888-866-5797. Page 4 Item 62422... -
Page 5: Double Insulated Tools: Tools With Two Prong Plugs
Association, and the National Electrical Code. 2. Double insulated tools may be used in either of the 120 volt outlets shown in the preceding illustration. (See Outlets for 2-Prong Plug.) For technical questions, please call 1-888-866-5797. Item 62422 Page 5... -
Page 6: Extension Cords
Read the manual before set-up and/or use. WARNING marking concerning Risk of Electric Shock. Properly connect power cord to appropriate outlet. For technical questions, please call 1-888-866-5797. Page 6 Item 62422... - Page 7 Parts List and Assembly Diagram on page 14. Speed Switch Trigger Lock Trigger (17) Hex Key Orbital Mode Level (16) Dust Chute Connector Blade Cover (14) Blade Release Lever Base Plate (19) Blade (sold separately) Roller Guide For technical questions, please call 1-888-866-5797. Item 62422 Page 7...
-
Page 8: Blade Installation
WARNING! Make sure blade’s back edge is set against the roller guide. 5. Release the blade release lever. Pull on blade until blade Collet snaps blade into place. For technical questions, please call 1-888-866-5797. Page 8 Item 62422... -
Page 9: Work Piece And Work Area Set Up
3. Use higher speeds to cut work pieces faster. NOTICE: Refer to the Blade Selection chart on page 7 to verify you are using the correct speed with the appropriate blade. Otherwise blade damage can occur. Figure 2 For technical questions, please call 1-888-866-5797. Item 62422 Page 9... -
Page 10: Dust Chute
Dust Chute with Trigger Trigger slots in Connector. Push Dust Chute in and (17) Lock turn clockwise to lock. See Figure 5, below. Dust Connector Chute Figure 5 Figure 4 For technical questions, please call 1-888-866-5797. Page 10 Item 62422... - Page 11 Saw Blade stops completely. Then, remove the Jigsaw from the work piece. 5. To prevent accidents disconnect the power cord after use. Clean, then store the tool indoors out of children’s reach. For technical questions, please call 1-888-866-5797. Item 62422 Page 11...
-
Page 12: Cleaning, Maintenance, And Lubrication
WARNING! If the supply cord of this corrected before further use. power tool is damaged, it must be replaced only by a qualified service technician. For technical questions, please call 1-888-866-5797. Page 12 Item 62422... -
Page 13: Troubleshooting
See Extension Cords in Grounding section on page 5. Follow all safety precautions whenever diagnosing or servicing the tool. Disconnect power supply before service. For technical questions, please call 1-888-866-5797. Item 62422 Page 13... -
Page 14: Parts List
If product has no serial number, record month and year of purchase instead. Note: Some parts are listed and shown for illustration purposes only, and are not available individually as replacement parts. For technical questions, please call 1-888-866-5797. Page 14 Item 62422... - Page 15 For technical questions, please call 1-888-866-5797. Item 62422 Page 15...
- Page 16 Limited 90 Day Warranty Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase. This warranty does not apply to damage due directly or indirectly, to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, criminal activity, improper installation, normal wear and tear, or to lack of maintenance.
Need help?
Do you have a question about the 62422 and is the answer not in the manual?
Questions and answers