Related Manuals for Tanaka THT-2530/2540
Summary of Contents for Tanaka THT-2530/2540
- Page 1 Illustrated Parts Manual Illustrated Parts Manual Model Number: THT-2530 / 2540 24cc, 1.3 hp Single Sided Hedge Trimmers Note: The THT-2530 has 30 inch blades. The THT-2540 has 40 inch blades. P/N 28581 Rev 000 Date 7/30/99...
-
Page 2: Product Information
Blades / inches (mm) Dry Weight / lbs. (kg) ISM, Inc. • 1028 4th Street SW, Suite B • Auburn, WA 98001 • Phone: (253) 333-1200 • Fax: (253) 333-1212 • E-mail: custsvc@tanaka-ism.com ™ reduces engine noise up to 44 percent. - Page 3 037-01601-200 PIN,PISTON 039-01620-200 CIRCLIP,PISTON PIN 046-06500-801 CRANKSHAFT 999-62081-225 BEARING,NEEDLE,F-810 153-21533-90 SET, COIL, IGNITION 994-16040-226 SCREW,WS,4X22 250-06500-200 TUBE,INSULATOR 178-06500-80 CORD,STOP COMPLETE 274-0700D-80 CORD, 130MM www.tanaka-usa.com PARTS INFORMATION ENGINE / CYLINDER, PISTON, CRANKSHAFT • FIGURE 1 DESCRIPTION Page 1 THT-2530/40 COMMENTS custsvc@tanaka-ism.com...
- Page 4 155-21523-80 ROTOR, MAGNETO 992-01080-011 WASHER,8 992-10080-012 WASHER,S,8 991-01080-011 NUT,8 100-02100-200 BOLT,STUD,6X22 www.tanaka-usa.com PARTS INFORMATION P/N 046-06500-801 DESCRIPTION Page 2 THT-2530/40 CRANKCASE, FLYWHEEL • FIGURE 2 COMMENTS Includes bearings, seals & gasket Shims are “as needed” to obtain correct c/s side clearance...
- Page 5 THT-2530/40 PARTS INFORMATION CARBURETOR, FUEL TANK, FUEL SYSTEM • FIGURE 3 P/N 455-06500-90 www.tanaka-usa.com Page 3 custsvc@tanaka-ism.com...
-
Page 6: Parts Information
CAP,GAS BLACK,NON VENT 659-00801-200 COLLAR 994-63050-185 BOLT,HEX 5X18PS 564-06601-90 VENT,AIR ASSY 565-06601-20 PIPE,AIR VENT 646-3252L-90 AIR VENT VALVE ASSY 680-00206-200 CLIP,5.5 561-00070-20 COVER,AIR VENT www.tanaka-usa.com PARTS INFORMATION CARBURETOR, FUEL TANK, FUEL SYSTEM • FIGURE 3 DESCRIPTION Page 4 THT2530/40 COMMENTS custsvc@tanaka-ism.com... - Page 7 785-06410-200 HANDLE,STARTER 994-15040-162 SCREW,PS,4X16 751-06500-200 GASKET, TAIL PIPE 721-06611-90 SET,TAIL PIPE 994-34040-081 SCREW,4X8/S 277-0634F-900 CLUTCH,ASS’Y 990-72045-164 SCREW,TAPPING,4.5X16 994-25040-128 BOLT,PS,4X12 790-06097-200 SPRING,STARTER PAWL 788-06500-20 PAWL,STARTER www.tanaka-usa.com PARTS INFORMATION CLUTCH, STARTER, MUFFLER COMPONENTS • FIGURE 4 DESCRIPTION Page 5 THT-2530/40 COMMENTS custsvc@tanaka-ism.com...
- Page 8 *GASKET, PUMP *DIAPHRAGM, PUMP *SCREEN, INLET 575-25182-80 BODY,PUMP *GASKET, DIAPHRAGM *DIAPHRAGM, METERING 476-25004-200 COVER,DIAPHRAGM 548-25101-200 SCREW,SET www.tanaka-usa.com PARTS INFORMATION DESCRIPTION Page 6 THT-2530/40 CARBURETOR ASSY • FIGURE 5 COMMENTS *Contained in Carb Repair Kit P/N 650-25140-900 (not available individually) custsvc@tanaka-ism.com...
- Page 9 THT-2530/40 PARTS INFORMATION CLUTCH, GEAR CASE • FIGURE 6 www.tanaka-usa.com Page 7 custsvc@tanaka-ism.com...
- Page 10 300-32250-801 NIPPLE,GREASE 990-51060-183 BOLT,HEX.HOLE,6X18 990-53060-153 BOLT,HEX,6X15 992-00060-011 WASHER,SMALL,6 070-33185-20 PLATE,FIXING 462-33185-20 PLATE,SUPPORT 990-51040-083 BOLT,HEX.HOLE 4X8 994-40060-011 NUT,SPRING 6 301-33185-20 CASE,GEAR B 992-10060-012 WASHER,S,6 994-40060-011 NUT,SPRING 6 www.tanaka-usa.com PARTS INFORMATION DESCRIPTION Page 8 THT2530/40 GEAR CASE • FIGURE 6 COMMENTS custsvc@tanaka-ism.com...
- Page 11 THT-2530/40 PARTS INFORMATION HANDLE, CUTTER BLADES • FIGURE 7 www.tanaka-usa.com Page 9 custsvc@tanaka-ism.com...
- Page 12 GUIDE,CUTTER 30" 121-33187-20 CUTTER B 30" 120-33187-20 CUTTER A 30" 129-33202-201 WASHER,7 124-33202-21 BOLT, CUTTER FIXING, A 128-37904-20 HOLDER,BLADE 123-3317A-20 NUT,CUTTER FIXING 138-3318B-21 COVER, CUTTER 30" www.tanaka-usa.com PARTS INFORMATION DESCRIPTION Page 10 THT2530/40 HANDLE, CUTTER BLADES • FIGURE 7 COMMENTS custsvc@tanaka-ism.com...
- Page 13 THT-2530/40 PARTS INFORMATION HANDLE, THROTTLE COMPONENTS • FIGURE 8 www.tanaka-usa.com Page 11 custsvc@tanaka-ism.com...
- Page 14 SCREW 4 X 16 /WS 991-78040-010 NUT,LOCK 4 990-11030-101 SCREW,3X10 258-11650-20 BUTTON,STOP 198-33130-200 CLAMP,CORD 994-61050-124 BOLT,HEX,5X12S 058-33185-20 BRACKET,HANDLE 060-33185-20 RUBBER,HANDLE DAMPER 813-20000-200 WRENCH,HEX,4 036-29331-501 SPANNER,COMBI www.tanaka-usa.com PARTS INFORMATION HANDLE, THROTTLE COMPONENTS • FIGURE 8 DESCRIPTION Page 12 THT2530/40 COMMENTS custsvc@tanaka-ism.com...
- Page 15 ITEM PART NUMBER 906-06612-20 PLATE,NAME THT-2540 906-06613-20 PLATE,NAME THT-2530 911-06500-200 DECAL,SRS 950-37900-200 DECAL,PRO-FORCE A 951-37900-200 DECAL,PRO-FORCE 920-32466-20 DECAL,CAUTION www.tanaka-usa.com PARTS INFORMATION DESCRIPTION Page 13 THT-2530/40 DECALS • FIGURE 9 COMMENTS custsvc@tanaka-ism.com...
- Page 16 Old Part # New Part # 992-01060-011 is marketed exclusively by: ISM, Inc. • 1028 – 4 Street, Suite B • Auburn, WA 98001 • Phone: (253) 333-1200 • Fax: (253) 333-1212 Description Remarks Washer www.tanaka-usa.com * custsvc@tanaka-ism.com BULLETIN NUMBER PI 3118...
- Page 17 123-33202-200 123-3317A-20 is marketed exclusively by: ISM, Inc. • 1028 – 4 Street, Suite B • Auburn, WA 98001 • Phone: (253) 333-1200 • Fax: (253) 333-1212 Description Remarks Lock Nut Reference #19 www.tanaka-usa.com * custsvc@tanaka-ism.com BULLETIN NUMBER PI 3119...
Need help?
Do you have a question about the THT-2530/2540 and is the answer not in the manual?
Questions and answers