1. Manuals
  2. Brands
  3. Pool Cover Specialists Manuals
  4. Lighting Equipment
  5. INFINITY 4000
  6. Installation manual

Pool Cover Specialists INFINITY 4000 Installation Manual

Automatic safety pool cover, under track system
Hide thumbs Also See for INFINITY 4000:
Table of Contents

Advertisement

Quick Links

INFINITY 4000
AUTOMATIC SAFETY POOL COVER
™
UNDER TRACK SYSTEM
INSTALLATION GUIDE
© Latham Pool Products, Inc. 2019. All rights reserved.

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the INFINITY 4000 and is the answer not in the manual?

Questions and answers

Related Manuals for Pool Cover Specialists INFINITY 4000

Summary of Contents for Pool Cover Specialists INFINITY 4000

  • Page 1 INFINITY 4000 AUTOMATIC SAFETY POOL COVER ™ UNDER TRACK SYSTEM INSTALLATION GUIDE © Latham Pool Products, Inc. 2019. All rights reserved.
  • Page 2 ™ The ECLIPSE Safety Pool Cover SECTIONS Cover Tracks ............5 Roll-up Mechanism .........6 Cover Fabric ............ 10 Classic Aluminum Lid ........17 Home Owner Check List ......19 Tools Required 18. Crescent wrench 1. Hammer drill or rotary hammer 2. Masonry drill bit 1/4” x 6” (1/4” x 12” bit) 19.
  • Page 3 Standard 18” Opposite Lid End 20. M4105 Standard UT Lid Bracket 21. LD2103 Drop in Anchor Plate Kit IM4010-R3LV-GLD Infinity 4000 110V Bison Low Voltage -RRT 22. MH232 Little Giant cover pump & instructions IM4010-R3-GLD Infinity 4000 110V Bison (Rec Right) 23. 22130...
  • Page 4 Step By Step Instructions COVER TRACKS Step By Step Instructions Page/Step Step by step installation instructions ....5/1 4 of 21 © Latham Pool Products, Inc. 2019. All rights reserved.
  • Page 5 Step By Step Instructions Step By Step Instructions Numbers in parenthesis refer to parts shown on page 3. To determine if the cover system was Cut the length of the track on each side of Before splicing the sections of track together, ordered correctly for the pool, the length of the pool so it will extend 1 inch past the end file all track ends thoroughly, rounding...

  • Page 6: Table Of Contents

    Step By Step Instructions MECHANISM Step By Step Instructions Page/Step Cover Box Preparation ........7/1 Connecting the Roll-up Tube ......7/2 Adjusting Mechanism Height ......7/4 Positioning the Mechanism ......7/7 Anchoring the Mechanism Feet ....8/12 Extending the Pulley Brackets ...... 8/13 Anchoring the Pulley Brackets ..... 8/18 5 Wire Motor Wiring ..........

  • Page 7: Cover Box Preparation

    Numbers in parenthesis refer to parts shown on page 3. Step By Step Instructions Cover Box Preparation Connecting the Roll-up tube Attach the hub casting on the motor end to the insert that is in the roll-up tube motor end Use a garden hose to clean out the cover box.

  • Page 8: Anchoring The Mechanism Feet

    Step By Step Instructions Anchoring the Mechanism Feet Align the mechanism on the motor side first On the non-motor end, make sure the rope by using a length of rope and extending it With the mechanism centered between the will travel straight from the track to the pulley. from the back side of the cover track to the tracks and centered in the cover box front to pulley to make sure the rope will feed...

  • Page 9: Wire Motor Wiring

    Step By Step Instructions Attach the #8 copper bond wire that is Make the same connection with the #8 stubbed into the cover box to the bonding copper bond wire that is in the cover box lug on the motor end of the mechanism. on the non-motor end of the mechanism.
  • Page 10 For the 3 Wire motor option, use the wiring diagrams below. Technical Wiring Schematic NOTE: The black wire may be replaced with blue depending on what motor is being used. 3 WIRE MOTOR BLACK WHITE GROUND 110-240 VAC HOT (LINE 2) 50/60 Hz NEUTRAL (LINE 1) 15 AMP GFCI...
  • Page 11 Step By Step Instructions COVER FABRIC Step by Step Instructions Page/ Step Opening the Cover Box ........12/1 Running Ropes in the Tracks ......12/4 Installing the Cover Tracks ......12/9 Routing the Ropes ..........13/11 Track Retainer ...........13/15 Magnet Installation ........13/18 Attaching the Leading Edge Tube ....14/21 Attaching the Ropes to the Reels ....15/32 Running out the Cover ........16/42...

  • Page 12: Opening The Cover Box

    Step By Step Instructions Numbers in parenthesis refer to parts shown on page 3 Opening the Cover Box Standing behind the housing looking over Uncoil the ropes to remove twists and kinks. the pool, unroll the cover from left to right. Run the ropes through the tracks.

  • Page 13: Routing The Ropes

    Step By Step Instructions Numbers in parenthesis refer to parts shown on page 3 Insert and tap the locking strip into place Routing the Ropes This rope will continue from the first pulley to underneath the track along the entire the second pulley.

  • Page 14: Attaching The Leading Edge Tube

    Step By Step Instructions Numbers in parenthesis refer to parts shown on page 3. Attaching the Leading Edge Tube On the front corner of the cover, that is on the Apply the supplied grease to the magnet. same side as the motor, insert a screw driver This will help it slide in the webbing easier.

  • Page 15: Attaching The Ropes To The Reels

    Step By Step Instructions Numbers in parenthesis refer to parts shown on page 3. Drill a 3/32” pilot hole through the top of the Drill a second hole using a 3/16” bit in the flat Connect the bonding wire that is attached to rope channel of the leading edge tube.

  • Page 16: Running Out The Cover

    Step By Step Instructions Numbers in parenthesis refer to parts shown on page 3. Installing the Sensor While holding the ropes over the mechanism, As the excess rope is wrapped around the run the key switch in the cover position. rope reel, make sure it goes on straight Thread the sensor into the mounting hole without getting crossed with each other.

  • Page 17: Adjusting The Ropes

    Step By Step Instructions Numbers in parenthesis refer to parts shown on page 3. 40 46 Using a utility knife, carefully cut a slit in With the cover in the fully closed position, Measure back 6-1/2 inches from the mark that mark the webbing where it is in line with was made on the webbing.
  • Page 18 Step By Step Instructions STANDARD ALUMINUM LID Step By Step Instructions Page/Step Installing the Lid Brackets........19/1 Assembling the Aluminum Lid ......19/4 Attaching the Lid to the Deck ....... 19/7 © Latham Pool Products, Inc. 2019. All rights reserved. 18 of 21...
  • Page 19 Step By Step Instructions Numbers in parenthesis refer to parts shown on page 3. Installing the Lid Brackets Install rope loops (25) on the rope along the Slide the standard lid bracket into the drop in back of the cover box. Secure the loops to anchor plate.
  • Page 20 After the cover system is installed, it is critically important to instruct the home owner on how to operate the cover system safely and do routine maintenance. Use the following check list and the Infinity 4000 Owner's Manual and Safety Information guide as your primary instruction source.
  • Page 21 Installation Checklist Tracks q All track ends filed. This is extremely important. q Does the track space measurement match how the cover system was ordered? q Cover goes through the track joints smoothly. q All track screws are tight and flush. q Pulleys are flush against the end of the track. q The guides are snug against the track.

Table of Contents

Save PDF