CONTENTS Important Safety Instructions Recommended •Personal Safety Precautions •Installation and Set-Up Instructions •Electrical Requirements (VS100, VS-500 & 502) •Electrical Specifications Spa Startup Directions Plug and Play Cord Location Operation Instructions •Topside Control Instructions (all single pump systems) •Topside Functions •Diagnostic Messages •Features found on various Viking models •Topside Control Instructions (all two pump systems) •Spa Jets and Air Controls...
IMPORTANT SAFETY INSTRUCTIONS When installing and using this electrical equipment, basic safety precautions should always be followed, including the following: READ AND FOLLOW ALL INSTRUCTIONS WARNING: To reduce the risk of injury, do 6. DANGER: Risk of Electric Shock. Do not not permit children to use this product permit any electrical appliance, such as a light, unless they are closely supervised at all...
Page 5
e) Persons using medication should consult 10. Never touch or come in contact with any a physician before using a spa since some electrical accessory when in your spa or when medication may induce drowsiness your body is wet. while other medications may affect heart rate, blood pressure and circulation.
15 amp RCD Rating weight as water refraction can be misleading. Viking 1P 120v, Viking 2P 120v, Aurora 1P 120v, Aurora PSL 120v, Royale P 120v, Royale PSL 120v, 5. Do not stay in the spa for extended periods of Regal P 120v, Regal PSL 120v time.
220-VOLT ELECTRICAL SPECIFICATIONS (VS500 & VS502 Power System) NOTE: All spa electrical wiring must be performed by a qualified, licensed electrician. WHITE BLACK GROUND* * Green ground connection located on left side of control panel.
SPA STARTUP DIRECTIONS All Viking Spas require a solid, flat surface.* This is to ensure that the spa cabinet is not exposed to a pressure stress condition that may result in cabinet damage and shell cracking. A concrete pad is the best example...
For the round Viking 1P or 2P spas, you will need to remove the panel with the cord cutout in the lower left hand section of the panel to access the RCD cord.
Page 10
VS100/500 VS100 System VS500 System Installed in: Viking 1P, Viking 2P Aurora 1P, Aurora Installed in: Viking 3, Aurora 3, Royale, Regal PSL, Royale P, Royale PSL, Regal P, Regal PSL It is very important to make sure that the spa is filled at least 3/4 way up the skimmer opening. Make sure the gate valves are in the open or up position.
OPERATION INSTRUCTIONS VS100/500 TOPSIDE CONTROL INSTRUCTIONS (All Models except Royale ETS, Regal ETS, Legacy, Legend, Heritage & Tradition) INITIAL START-UP TEMPERATURE (26°C - 40°C) When your spa is first activated, it will go into The start-up temperature is set at 37°C. The last Priming mode, indicat-ed by “Pr”.
OPERATION INSTRUCTIONS VS100/500 TOPSIDE FUNCTIONS Standard Mode is programmed to maintain the desired temperature. Note that the last measured spa temperature displayed is current only when the JETS pump has been running for at least 2 minutes. “St” Press the “Jets” button once to activate the low will be displayed momentarily when you switch into speed of the pump and again for the high speed.
DIAGNOSTIC MESSAGES Message Meaning Action Required Temperature Unknown After the pump has been running for 2 minutes, the temperature will be displayed. DO NOT ENTER THE WATER. Remove the cover “Overheat” – The spa has has shut down. One of the sensors has detected and allow water to cool.
Page 14
OPERATION INSTRUCTIONS VS100/500 WATERFALL ADJUSTABILITY LED LIGHTING FEATURE The Aurora P, Aurora PSL and the Aurora 3 feature The Aurora PSL, Royale PSL, Regal PSL, Viking 3, a Waterfall, which allows the user to regulate the Aurora 3, Royale, Royale ETS, Regal, Regal ETS, flow of water to the jet by simply turning the valve Legacy, Legend, Heritage &...
OPERATION INSTRUCTIONS VS502 (Royale ETS, Regal ETS, Legacy, Legend, Heritage & Tradition) VS502 System TOPSIDE CONTROL INSTRUCTIONS Controls Low Speed/High Pump 2 Controls Secondary Displays Temperature and Speed Pump Pump, On and Off Diagnostic Messages Turns Light ,-On/Off Heat On Indicator Light Sets Water Temperature INITIAL START-UP Press the “Temp”...
OPERATION INSTRUCTIONS VS502 (Royale ETS, Regal ETS, Legacy, Legend, Heritage & Tradition) PUMP 1 Economy Mode heats the spa to the set temperature only during filter cycles. “Ec” will display solid when temperature is not current, and Press the “Pump 1” button once to activate the low will alternate with temperature when temperature is speed of the pri-mary pump and again for the high current.
OPERATION INSTRUCTIONS VS502 (Royale ETS, Regal ETS, Legacy, Legend, Heritage & Tradition) SPA JETS AND AIR CONTROLS SPA JETS Adjustable Spa Jets may be turned off and on by rotating jet faceplate left or right. NOTE: DO NOT TURN ALL SPA JETS OFF AT THE SAME TIME.
To turn the Turbo jet off, turn the face Viking 1P, Viking 2P, Viking 3 Only clockwise to bring the main jets back to full power.* The Volcano Jet operates on a valve located in the middle of the lounger.
(Fully extended up position). SKIMMER SIDE FILTER All Viking spas have a skimmer side filter that does not require “air bleeding” on initial startup. If an air lock develops, loosen the union on return side of pump.
MAINTENANCE SPA DRAINING DRAIN LOCATIONS Every 90 days, depending upon water condition, you may need to renew the spa water. To drain your spa, power must be disconnected at the circuit breaker. Locate the drain faucet inside the Water Gate Valve spa cabinet (for Viking IP, 2P &...
MAINTENANCE SPA SURFACE CARE SPA PILLOW MAINTENANCE Do not use abrasive solvents or cleaners to • Your spa pillows need to be washed and rinsed clean spa surfaces. Only use the following: periodically to remove any chemical residue. This Lemon Juice, Amonia, Vinegar or Soap and should help to eliminate pillows becoming stiff and Water.
FILTER CLEANING FILTER CLEANING (Viking 1P, Viking 2P & Viking 3) (All Spas except Viking 1P, Viking 2P, Viking 3) Your filter should be replaced once a year. When filters Remove filter face cover by pulling straight up and are removed from the spa, make sure that no objects fall slightly toward the spa on front plate/face cover.
OZONATOR If your spa is equipped with an ozonator, it is factory set to filter during the filter cycles only. We recommend the F4 setting which means your spa will filter a total of 8 hours (4 hours twice a day). This should provide adequate ozonation, provided there is proper chemical bal-ance in the spa.
SPA SITUATIONS & SOLUTIONS Situation Cause or Result Product to use Solution Add 28 gm’s of Stain n Scale Calcium deposits on Hard water Stain n Scale surfaces of heater, fittings or plumbing pH/total alkalinity out of pH Up Test water - adjust adjustment pH Down with pH Up or pH...
TROUBLE SHOOTING Caution: Viking Spas have slide type water shut off valves referred to as Gate Valves. The spa should never be operated with the Gate Valves in the closed position, as this will cause severe damage to the pump and/ or heater.
Need help?
Do you have a question about the Viking 1P and is the answer not in the manual?
Questions and answers