Download Print this page

Sealey RS103.V3 Instructions

Roadstart units

Advertisement

Quick Links

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to
Warning:
Instruction
Explosion
Manual
Risk
1. SAFETY
Read and understand the general safety and operating instructions before use. The following information is intended to help you
keep the product in top working order.
NOTE - The battery in this unit is a consumable item and its ability to accept charge will reduce over time. We will warranty it against
mechanical and electrical defect for a period of one year - this does not cover fair wear and tear.
If the battery is not properly charged before first use, or regularly conditioned, its capacity will diminish. Under these circumstances we will not
replace the battery even if it is less than one year old.
You can help prolong the life cycle of the battery by following a few simple guidelines.
Plug in your new Roadstart to the mains transformer and make an INITIAL charge lasting 72 hours.
Ensure the unit is fully charged before storage.
DO NOT leave the Roadstart for longer than 2 months without putting it on charge.
DO NOT attempt to start a vehicle when the Roadstart battery voltage is reduced to less than 7.25Volts.
DO NOT drop or roughly handle the Roadstart - this will break or disjoin the battery terminals rendering the battery useless and the warranty
void.
DO NOT use any other charger, other than the one supplied, to recharge the battery.
DO NOT obstruct the ventilation grilles and protect against water ingress - these RoadStart units are fitted with ventilation grilles to help
disperse any gases produced during the charging procedure.
IMPORTANT: To reduce the risk of a battery explosion, follow these instructions and those published by the battery manufacturer and the
manufacturer of any equipment you intend to use in the vicinity of the battery. Remember to review warning marks on all products and on engines.
Modern vehicles contain extensive electronic systems. You are required to check with the vehicle manufacturer, for any specific
instructions regarding the use of this type of equipment on each vehicle.
No liability will be accepted for damage/injury, where this product is not used in accordance with all instructions.
1.1.
PERSONAL PRECAUTIONS
Ensure there is another person within hearing range, or close enough to come to your aid should a problem arise, when working near a
9
lead-acid battery.
Have fresh water nearby in case battery acid contacts skin, clothing or eyes.
9
Wear safety eye protection and protective clothing. Avoid touching eyes while working with a battery.
9
If battery acid contacts skin or clothing flush area with water. If acid enters eye, flush eye immediately with cool, clean running water for
9
at least 15 minutes and seek immediate medical attention. MSDS available from sealey.co.uk.
Remove personal metallic items such as rings, bracelets, necklaces and watches. A lead-acid battery can produce a short-circuit current
9
high enough to weld a ring or the like to metal, which may cause severe burns.
1.2.
IMPORTANT SAFETY INSTRUCTIONS
Familiarise yourself with the applications, limitations and potential hazards of the RoadStart.
9
Keep the unit in good working order and condition. Replace damaged parts immediately.
9
Use only recommended parts. To use unapproved parts may be dangerous and will invalidate your warranty.
9
The RoadStart must only be opened and checked by qualified service personnel. DO NOT disassemble the unit for any reason.
9
Keep children and unauthorised persons away from the work area.
9
Keep work area clean and tidy and free from unrelated materials.
9
Ensure that there is adequate lighting.
9
If the RoadStart receives a sharp knock or blow, it must be checked by a qualified service agent before being used.
9
When not in use re-charge every two months.
9
DO NOT smoke or allow a spark, or flame in the vicinity of the battery or engine.
8
DO NOT drop any metal item onto the battery as it may spark or short circuit the battery, which could cause an explosion.
8
DO NOT use RoadStart to recharge dry cell batteries that are commonly used with home appliances. These batteries may explode and
8
cause personal injury and damage to property.
DO NOT charge or boost a frozen battery.
8
DO NOT use attachments other than those recommended. To do so may risk damage to the unit and other equipment and possible
8
personal injury.
DO NOT pull or carry the unit by its cables and do not pull the negative and positive clamps from the battery terminals.
8
© Jack Sealey Limited
ROADSTART UNITS
MODEL NO'S:
Wear eye
Warning:
Protection
Corrosive
substance
IMPORTANT WARRANTY INFORMATION: KEEP YOUR ROADSTART HEALTHY
Original Language Version
RS1.V5 / RS102.V4 / RS103.V3
Wear
Warning:
Protective
Electricity
Gloves
RS1.V5 RS102.V4 RS103.V3 Issue 7 (3,4) 29/4/19
Protect
Use in
Keep away
From
Well
from sources
Rain
Ventilated
of ignition:
Areas
Battery could
explode

Advertisement

loading

Summary of Contents for Sealey RS103.V3

  • Page 1 RS1.V5 / RS102.V4 / RS103.V3 MODEL NO’S: Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions, and properly maintained, give you years of trouble free performance. IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED.
  • Page 2 It is particularly important to use an RCD with portable products that plug into an electrical supply not protected by an RCCB. If in doubt consult a qualified electrician. You can obtain a Residual Current Device through your Sealey stockist.
  • Page 3 RS1.V5 & RS102.V4 Use the charger supplied (fig.5). Plug the AC charger cable into the charge input socket of the unit. This socket 4.4.1. is situated on the back of the unit at the top of the label (fig.1). RS103.V3 Use the charger supplied (fig.5). The adaptor charging jack is inserted into the charge port, located beneath the LED 4.4.2. power indicators.
  • Page 4 The dc outlet on the RoadStart units is equipped with overload protection. 5.3.3. The twin battery model RS103.V3, when used with an inverter, can operate equipment usually powered by either 110V ac or 230V ac. NOTE: The inverter power draw must not exceed 300 Watts.

This manual is also suitable for:

Rs102.v4Rs1.v5