Page 1 ProtoTRAK ® K3 Knee Mill & Retrofit Safety, Installation, Maintenance, Service & Parts List Manual Document: P/N 29777 Version: 091018 2615 Homestead Place Rancho Dominguez, CA 90220-5610 USA T | 310.608.4422 | F | 310.764.2668 Service Department: 800.367.3165 e-mail: sales@trakmt.com service@trakmt.com web: www.trakmt.com...
Page 2  Copyright 2018, Southwestern Industries, Inc. All rights are reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means, mechanical, photocopying, recording or otherwise, without the prior written permission of Southwestern Industries, Inc.
Page 3: Table Of Contents
Table of Contents Safety ......................1 Safety Publications ....................1 Danger, Warning, Caution, and Note Labels & Notices As Used In This Manual ..1 Safety Precautions ....................4 Installation ....................6 Floor Plan, Layout & Space Requirements – K3 ............6 Uncrating ......................
Page 4: Table Of Contents
3.3.1 Fault X or Y ....................29 KMX Pendant Troubleshooting LED’s ..............31 Service Codes ..................33 Software ......................33 Machine Set-Up ....................33 Diagnostic Codes ....................34 Operator Defaults/Options ..................35 CODE 11: Hysteresis ................... 35 CODE 12: Feed Forward Constant ................ 36 CODE 97: Set Positive Motor Encoder Direction .............
Page 5: Table Of Contents
20255-1 PARTS LIST FOR DRIVE KIT – X-AXIS-SM ..........78 23083-XX DRIVE KIT-SPORT – Y-AXIS ..............78 23083-1 PARTS LIST FOR DRIVE KIT-SPORT - Y-AXIS ..........78 28092-1 BRACKET ASSY-BP SER I Z AXIS - SWI GS ..........78 20586-1 BRACKET ASSY-Z AXIS EASSON GLASS SCALE .......... 78 8.10 25000-XX DRIVE KIT - Z AXIS ................
Page 6: Safety
Safety The safe operation of the TRAK K Mills depends on its proper use and the precautions taken by each operator. Read and study this manual and the ProtoTRAK KMX Programming, Operating, and Care  Manual. Be certain every operator understands the operation and safety requirements...
Page 7 Safety & Information Labels Used On The TRAK K Milling Machines It is forbidden by OSHA regulations and by law to deface, destroy or remove any of these labels Southwestern Industries, Inc. ProtoTRAK KMX K3 & Retrofit Safety, Installation, Maintenance, Service & Parts List Manual...
Page 8 Safety & Information Labels Used On The TRAK K3 Milling Machines It is forbidden by OSHA regulations and by law to deface, destroy or remove any of these labels Power Requirements at 220 and 440 Volts, 3-phase 60 Hz KMX K3...
Page 9: Safety Precautions
Safety Precautions Do not operate this machine before the TRAK K Mill Installation, Maintenance, Service and Parts List Manual, and ProtoTRAK KMX Programming, Operating & Care Manual have been studied and understood. Do not run this machine without knowing the function of every control key, button, knob, or handle.
Page 10 Use correct cutting parameters (speed, feed, depth, and width of cut) in order to prevent tool breakage. Use proper cutting tools for the job. Pay attention to the rotation of the spindle: Left hand tool for counterclockwise rotation of spindle, and right hand tool for clockwise rotation of spindle.
Page 11: Installation
Installation Read and understand this entire installation section before beginning the installation procedure. Figure 1 – Machine Footprints Floor Plan, Layout & Space Requirements – K3 Weight (approximate) net 2800 lbs Weight (approximate) shipping 3100 lbs Pallet Size 6’ x 6’ Overall width 103”...
Page 12 Figure 2 – Overall Dimensions Table Size 10” x 50” T-Slots (number x width) 3” x 5/8” Dimension G 87” Dimension G Min 65” Dimension H Min 64” Dimension H Max 78” Dimension I Min 38” Dimension I Max 49’ Dimension J Max 17”...
Page 13: Uncrating
Toolbox with various tools ______ ProtoTRAK KMX Safety, Operation & Programming Manual (P/N 29831) ______ TRAK K3 KMX Knee Mill & Retrofit Safety, Installation, Maintenance, Service & Parts List Manual (P/N 29777) ______ Way covers K3 – front of saddle - 20872 ______ Way covers K3 –...
Page 14: Installation Instructions & Checklist
See drawing 29756-1 at the rear of the manual.  On retrofits and TRAK knee mills make sure to plug in the machine ID key on the pendant.  Turn on the power to the machine and to the pendant.
Page 15: Machine Specifications
(i.e. motor encoder only).  25. 1 Check for positional accuracy and repeatability on the X and Y-axis using programs SWI Test programs 1.PT4 and 2.PT4 respectively. Positioning and repeatability values should be less than or = to 0.0005”.  26.
Page 16: Maximum Work Capacities
Maximum Work Capacities Drilling Mild Steel (2-axis manual feed) 1 ¼” Tapping Mild Steel 1” Milling (metal removal rate/mild steel) 1 ½ inch /min Drilling (3-axis systems) ½” Maximum work capacities are dependent on a lot of variables that cannot be controlled by the machine manufacturer.
Page 17  Machine Tool Error Compensation and Backlash Compensation custom set on mill after installation  Selectable Inch/mm measurement readout  Jog of X and Y from 1 to 100 inches per minute  Selectable 2 or 3-axis operation  AGE Auto Geometry Engine Programmed Canned Cycles ...
Page 18 Figure 3 - Knee Mill Component Identification Item Part Number Description 20819 Spindle Motor 29751-1 KMX Pendant 15616 Y-Axis Handwheel (Saddle) 15616 X-Axis Handwheel (Table) 20296 X, Y or Z Motor 24101-4 Servo driver 29770-1 Cable Breakout Box 15609-12, -16, -19 Y Axis Ballscrew –...
Page 19 Figure 4 - Knee Mill Rear View Item Part Number – K3 Description 220V=20676 Electrical Box 440V=20676 29770-1 Cable Breakout Box (optional) 9001 Lube Pump 20676-2 Electrical box (if have tableguard option) Southwestern Industries, Inc. ProtoTRAK KMX K3 & Retrofit Safety, Installation, Maintenance, Service & Parts List Manual...
Page 20: Lifting And/Or Moving The Machine
Lifting and/or Moving the Machine CAUTION! The K3 machine weighs approximately 2800 lbs. Proper equipment of sufficient capacity must be used when lifting and/or moving the machine. (See Figure 5 to Prepare the Mill before Lifting): Using a steel cable with protective sleeving (min 3/4” diameter) or a 3-ton sling, position sling loops on machine as shown in Figure 5.
Page 21 Figure 5 - Lifting the Machine Southwestern Industries, Inc. ProtoTRAK KMX K3 & Retrofit Safety, Installation, Maintenance, Service & Parts List Manual...
Page 22: Cleaning
Cleaning Remove rust protective coating from the machine before moving any slideways (table, saddle, knee, etc.). The coating is best removed with clean, dry rags. Do not use a cleaning solution that may damage the rubber way scrapers, plastic parts, or paint. WARNING! Do not use gasoline or other flammable cleaning agents for cleaning the machine.
Page 23 Figure 6 - Placement of Levels Item Title FC112 LEVEL SCREW FC113 LOCK HEX NUT FC114 LEVELING PAD i00138 Figure 7 - Leveling Screws Southwestern Industries, Inc. ProtoTRAK KMX K3 & Retrofit Safety, Installation, Maintenance, Service & Parts List Manual...
Page 24: Electrical Connection
2.11 Electrical Connection The TRAK K3 Knee Mill can be configured for 220 or 440 volt 3 phase electricity. These machines also require a 110V power source to power the control. DANGER! Be certain that 200-volt electricity (typical range 208 – 240V) is used only with a machine labeled 220 volts at the motor and at the electrics box on the back of the column.
Page 25 Figure 7.1 – Spindle Motor Rewiring Southwestern Industries recommends the machine be earth grounded by driving a copper rod into the ground. It is the responsibility of the customer to install this rod. Southwestern Industries, Inc. ProtoTRAK KMX K3 & Retrofit Safety, Installation, Maintenance, Service & Parts List Manual...
Page 26 Figure 8 - Wiring K3– Not for Retrofit Part Number Description 220V & 440V = 20676 Electrical Box 220V & 440V = 23438-3 Overload 23436 Contactor (Qty = 2) (Reverse or Forward) NOTE: If equipped with Table Guard Option, the Electrical Box the P/N is 20676-2. Southwestern Industries, Inc.
Page 27: Air Connection - Optional
2.12 Air Connection - Optional The K mill machines have an air hookup in the rear of the machine if the machine has a power drawbar or auxiliary function option. Auxiliary function options are only found on 3 axis mills. If the machine has a power drawbar option then the machine will include an air regulator, air manifold and an oiler.
Page 28: Lubrication
2.15.1 Manual Lubrication The TRAK mill X & Y way surfaces and ball screws need to be manually lubricated. The Manual Lube automatically discharges about 4ml of oil every plunge. At the beginning of each day, manually pull the pump handle.
Page 29 Figure 9 - Knee Mill Lubrication Southwestern Industries, Inc. ProtoTRAK KMX K3 & Retrofit Safety, Installation, Maintenance, Service & Parts List Manual...
Page 30: Head Lubrication
2.15.2 Parts List –Knee Mill Lubrication (Figure 9) Item Title 9001 HAND OILER 9002 ALUMINUM PIPE 9003 ELBOW 9004 T-JOINT - 4 HOLES- M8 X 1.0 9005 CONNECTOR 9006 REGULATING DISTRIBUTOR 9007 FLEXIBLE TUBE - 21 inches 9008 SCREW NUT - M8 X 1.0 MALE 9009 SCREW NUT - PD 1/8- 19MM 9010...
Page 31 Every Four Months: Apply a good grade of general-purpose grease through the grease fittings on the back of the head. This grease lubricates the Low range gear set and the feed change gears respectively. Lubricate vari-disk on spindle motor by means of grease fitting on motor shaft.
Page 32: Troubleshooting By Symptom
Troubleshooting by Symptom Use this section to begin the process of resolving a service problem. Each symptom type is described in a few words and then more fully described in an explanatory paragraph. Following this is a chart that directs in the most logical steps Problems Relating to Machining Results 3.1.1 Poor Finish...
Page 33: Problems Regarding The Motion Of The Machine
Note: The typical slideway-milling machine is not capable of achieving more precise results although careful adjustments to a new milling machine may produce better results. If more precise circles are required, then it is recommended to use a precision boring head/boring bar. Do the following Service Codes and document values: ...
Page 34: Axis Will Not Jog
 Code 100 Axis open loop test. Used to check the maximum feedrate of an axis and if the encoders are counting properly.  Code 131 Manual DRO – turn handwheels to check motor encoder counts vs glass scale counts Possible Cause Check This Motor encoder versus glass scale...
Page 35  Code 33 Software Identification. This is needed if you call SWI Customer Service.  Code 100 Axis open loop test. Used to check the maximum feedrate of an axis and if the encoders are counting.  Code 131 Manual DRO – turn handwheels to check motor encoder counts vs glass scale counts Possible Cause Check This...
Page 36: Kmx Pendant Troubleshooting Led's
KMX Pendant Troubleshooting LED’s The following LED’s are found on the back of the KMX pendant and may be useful when troubleshooting with our customer service department. 24VDC K100-FB 12VDC K101-FB 5 VDC K100-OUT 5-1VDC K101-OUT 3.3VDC K100-FAULT K101-FAULT DOOR SW1 WDT- FAULT DOOR SW2 SPARE 1...
Page 37 Description WDT-FAULT Watchdog fault indicator. Slow blink (1 sec on/1 sec off) = Normal operation. Fast blink (5 time/sec) = Watchdog fault occurred. If this occurs, reboot to see if the problem is solved. If not, the pendant/computer module will most likely need to be replaced.
Page 38: Service Codes
Service Codes The following is a list of service codes used on the KMX control system. The Service Codes are divided into logical categories. The table below is a quick summary of the service codes. More detailed information can be found below. All Service Codes are accessed in the SET-UP Mode by pressing the soft key for “SERV CODES”.
Page 39: Diagnostic Codes
Toggle X Glass Scale On or Turn on or off Toggle Y Glass Scale On or Turn on or off Reverse X EHW Direction Change direction of EHW on X axis Reverse Y EHW Direction Change direction of EHW on Y axis Toggle Limit Switches On or Turns limit switches on or off Reverse Y Position Sensor...
Page 40: Operator Defaults/Options
Message Log Logs the machine as it runs. It captures all key presses, error messages and data as the machine runs. It is saved automatically with service code 1. Fault Log A log that captures all faults and error messages. Error Message Display Displays error messages on screen Display Memory Check...
Page 41: Code 12: Feed Forward Constant
Explanation: As an overall measure of the system hysteresis, we are looking for the X and Y values to be less than .004". A value greater than this indicates a problem with either excessive friction or play that may affect the finish or accuracy of machined parts. CODE 12: Feed Forward Constant The Code 12 procedure helps the control “learn”...
Page 42: Code 100: Axis Open Loop Test
 Y - saddle moves toward the front (so the tool moves up relative to the workpiece).  Z – the head moves up (DPM machines)  Z - the quill moves up. If you do not move correctly from the beginning, repeat the procedure. Press INC SET to signal the procedure is complete.
Page 43: Code 122: X, Y, Z And Quill Calibration Using Part Measurements
Your input Motor encoder reading nothing (should be 0) Table encoder reading Feedrate the maximum feedrate attained Your input nothing (should be 0) Motor encoder reading Table encoder reading Feedrate the maximum feedrate attained Your input nothing (should be 0) Motor encoder reading Table encoder reading Feedrate...
Page 44: Code 123: X, Y, Z And Quill Calibration
To calculate your offset with a 1.0000” difference in position, measure the actual amount machined and compare it with 1.0000”. For example, if your measurement showed the difference between the reference plane and the machined plane is 0.9975”, calculate the offset: Z calibration offset = DRO ÷...
Page 45: Maintenance
Maintenance Gib Adjustments The objective of adjusting the gibs is to eliminate as much play in the table and saddle sliding surfaces as possible without having the tightness of the gib interfere with their free movement and cause a decrease in the accuracy and/or performance of the machine due to excessive friction.
Page 46 Figure 12 - Table Gib Adjustment Move the left end of the table back and forth and note the amount of movement on the dial indicator. Adjust the X-axis gib until the registered movement is .0010-.0015. To adjust the gib for excessive clearance: Loosen the gib lock screw on the right end of the saddle.
Page 47: Saddle Side Gib Adjustment, Y-Axis
Figure 14 - Saddle Side Gib Adjustment 5.1.2 Saddle Side Gib Adjustment, Y-Axis See Figure 14. Clean all chips, dirt and excess oil from the table and saddle. Center the saddle on the bed ways. Move the table fully to the left side of the saddle. Remove the chip wiper guard and chip wiper from the front and rear of the left side box way.
Page 48: Saddle Bottom Gib Adjustment, Y-Axis
5.1.3 Saddle Bottom Gib Adjustment, Y-Axis See Figure 15. Clean all chips, dirt and excess oil from the table and saddle. Center the saddle on the bed ways. Move the table fully to the left side of the saddle. Attach a .0001 dial indicator with a magnetic base to the left front of the saddle.
Page 49: Head Rotational And Tramming
Head Rotational and Tramming The TRAK knee head is free to rotate up to 90 degrees to the right or left. The K3 can also rotate 45 front to back. 5.2.1 To Rotate the Head Side to Side: Loosen the four locknuts.
Page 50: Back To Front Adjustment
Figure 16 - Tramming of Head 5.2.3 Back to Front Adjustment Make sure the table has been clean. Mount a dial indicator in a tool holder and mount in the quill. Adjust the Y-axis so that the spindle is in the center of the table. Adjust the knee so that the dial indicator will reach the table and lock the 2 clamps on the knee.
Page 51: Introduction To Self-Service
Introduction to Self-Service The objective of this section of the manual is to allow the user of the ProtoTRAK Control to resolve the majority of potential service problems. This manual assumes that the user is not experienced with CNC troubleshooting and repairs. Special tools are not required for the procedures described in the manual.
Page 52: Return Authorization (Ra) Number
6.2.2 Return Authorization (RA) Number All shipments of replacement parts are accomplished through our Return Authorization (RA) system. At the same time the CSR is diagnosing the problem and ordering the part, they will issue an RA number that will allow us to efficiently process the return part.
Page 53: Figures And Parts Lists
Figures and Parts Lists Figure 17- K3 - Top Housing Assembly Southwestern Industries, Inc. ProtoTRAK KMX K3 & Retrofit Safety, Installation, Maintenance, Service & Parts List Manual...
Page 54 Parts List - K3 -Head Top Assembly (Figure 17) Item Title 20778-1 GEAR HOUSING ASSY 20778-2 HI-LOW SHIFT CLUTCH ASSY 20778-3 HI-LOW SHIFT ASSY VS12 FRU-K3-SOCKET CAP SCREW M6-P1.0x15L 20778-4 PULLY PINION ASSY VS64 FRU-K3-BULL GEAR PINION BEARING CAP VS93 FRU-K3-SCREW M5-P0.8x15L VS117 FRU-K3-KEY 5x525L...
Page 55 Figure 18- K3 - Gear Housing & Parts List Item Title VS82 FRU-K3-GEAR HOUSING VS112 FRU-K3-GUIDE SPRING VS113 FRU-K3-SPRING GUIDE PIN i20778-1 Southwestern Industries, Inc. ProtoTRAK KMX K3 & Retrofit Safety, Installation, Maintenance, Service & Parts List Manual...
Page 56 Figure 19 - K3 - Hi-Low Shift Clutch Sub-Assembly Southwestern Industries, Inc. ProtoTRAK KMX K3 & Retrofit Safety, Installation, Maintenance, Service & Parts List Manual...
Page 57 Parts List –High-Low Shift Clutch Item Title VS75 FRU-K3-BEARING SLEEVE VS77 FRU-K3-BALL BEARING (2 REQ.) 6908ZZ VS78 FRU-K3-BEARING SPACER VS79 FRU-K3-BEARING SPACER VS80 FRU-K3-SNAP RING R-65 VS73 FRU-K3-SPLINED GEAR HUB VS72 FRU-K3-KEY 8x7x10L VS74 FRU-K3-SPINDLE BULL GEAR VS114 FRU-K3-WASHER VS115 FRU-K3-EXTERNAL TOOTH WASHER Ø...
Page 58 Parts List - Hi-Low Shift Item Title VS89 FRU-K3-HI-LOW DETENT PLATE VS87 FRU-K3-CLUTCH GEAR SHAFT VS92 FRU-K3-HI-LOW PINION BLOCK VS91 FRU-K3-SPRING VS90 FRU-K3-HI-LOW DETENT PLUNGER VS94 FRU-K3-HI-LOW SHAFT CRANK VS88 FRU-K3-PIN Ø 3X19L VS93 FRU-K3-SCREW M5-P0.8x15L VS92-1 FRU-K3-SET SCREW M5-P0.8x5L VS92-2 FRU-K3-WASHER- FLAT Ø...
Page 59 Figure 21 - K3 - Pulley Pinion & Parts List Parts List - K3 Pulley Pinion Item DESCRIPTION VS67 FRU-K3-BULL GEAR PINION COUNTER SHAFT VS69 FRU-K3-KEY 5X5X18L VS66 FRU-K3-BULL GEAR PINION AK118 BEARING-DEEP GROOVE-6203ZZ FRU-K3-SOCKET SET SCREW M6-P1.0x6L 23954 BEARING-DEEP GROOVE-SET (2)-6203ZZ i20778-4 Southwestern Industries, Inc.
Page 60 Figure 22 - K3 - Lower Vari-Disc Drive (assembly not available, order parts separately) Southwestern Industries, Inc. ProtoTRAK KMX K3 & Retrofit Safety, Installation, Maintenance, Service & Parts List Manual...
Page 61 Parts List – K2/K3 Lower Vari-Disc Drive (Figure 22) Item Title VS50 FRU-K3-BELT HOUSING BASE VS59 FRU-K3-BRAKE BLOCK VS58 FRU-K3-TURNING BLOCK SHAFT VS103 FRU-K3-RETAINING RING Ø 7 VS51 FRU-K3-SET SCREW M6-1.0X6L VS53 FRU-K3-BRAKE LOCK BUSHING VS52 FRU-K3-BRAKE LOCK SHAFT VS52-2 FRU-K3-BRAKE LOCK PIN DIA 3 X 5/8"L VS47 FRU-K3-BRAKE SHOE...
Page 62 Figure 23 - K3 - Upper Vari-Disc Drive Sub-Assy Parts List – K3 Upper Vari-Disc Drive Sub-Assy VS42 FRU-K3-SPINDLE PULLEY BEARING HOUSING 24643 BEARING-DEEP GROVE-6210ZZ VS44 FRU-K3-ADJUSTABLE-DRIVEN VARIDISC VS36 FRU-K3-SPEED CHANGE PLATE VS38 FRU-K3-PIVOT SLEEVE Ø 5 VS37 FRU-K3-WASHER M5 P0.8X20L VS123 FRU-K3-SCREW-SHCS M5-0.8X20L Southwestern Industries, Inc.
Page 63 VS39 FRU-K3-SPEED CHANGE PLATE PIVOT STUD VS41 FRU-K3-WASHER Ø 8.2 VS40 FRU-K3-ROLL PIN Ø3x15L VS35 FRU-K3-ADJUSTMENT NUT VS34 FRU-K3-CHAIN END STUD VS33 FRU-K3-CHAIN FRONT SCREW M4-P0.7x5L VS97 FRU-K3-SNAP RING Ø 35 FVS96 JAM NUT 3/8-16NC 24564 BEARING HOUSING ASS'Y - K2/K3 24631 VARIDISC ASSY-ADJUSTABLE VS31...
Page 64 Figure 24 - K3 - Speed Change Handwheel & Parts List Item DESCRIPTION VS16 SPEED CHANGE HOUSING VS20 BEARING SELF LUBRICATING VS22 SPEED CHANGER GEAR VS31 SPEED CHANGE CHAIN DRUM VS21 WORM VS25 SPEED CHANGE SHAFT VS40 ROLL PIN Ø3x15L VS24 COPPER BUSHING VS24-1...
Page 65 Figure 25 - K3 - Spindle Motor & Parts List Item Title VS110 FRU-K3-MOTOR 3 HP VS3-1 FRU-K3-KEY 6x6x45L FRU-K3-STATIONARY MOTOR VARIDISC FRU-K3-BUSHING FRU-K3-ADJUSTABLE MOTOR VARIDISC ASSY. VS6-1 FRU-K3-KEY 7x7x50L FRU-K3-SPRING FOR VARIDISC MOTOR SHAFT FRU-K3-ADJUSTABLE VARIDISC SPRING COLLAR VS10 FRU-K3-SCREW- SOC HD CAP M8-P1.25x30L 23953 VARIDISC ASSY-ADJUSTABLE MOTOR...
Page 66 Figure 26- K3 - Lower Head Assembly Southwestern Industries, Inc. ProtoTRAK KMX K3 & Retrofit Safety, Installation, Maintenance, Service & Parts List Manual...
Page 67 Parts List – K3 Lower Head Assembly (Figure 26) Item Title K-B125-2 FRU-K3-HANDWHEEL HANDLE (AVAILABLE ONLY IN ASSY. 20835) K-B113 FRU-K3-HAND WHEEL CLUTCH K-B117 FRU-K3-ROLL PIN Ø3x15L K-B103 FRU-K3-CAM ROD K-B108 FRU-K3-SOCKET SET SCREW M6-P1.0x8L K-B119-1 FRU-K3-ROLL PIN Ø3x20L K-B103-1 FRU-K3-CAM ROD PIN Ø6x15L K-B107 FRU-K3-CAP SCREW M6-P1.0x25L...
Page 68 K-B177 FRU-K3-SPRING COVER K-B169 FRU-K3-RD.HEAD SCREW(2REQ.) M5-P0.8x15L K-B170 FRU-K3-ROLL PIN K-B175-3 FRU-K3-SET SCREW M8-P1.25x6L K-B175-2 FRU-K3-COMPRESSION SPRING K-B175-1 FRU-K3-STEEL BALL K-B176 FRU-K3-PINION SHAFT HUB SLEEVE K-B175 FRU-K3-RACK FEED HANDLE HUB K-B172 FRU-K3-PINION SHAFT HUB SCREW 20836 SPINDLE ASSY-K2/K3 VS109 DRAWBAR-R8-MANUAL VS109-1 FRU-K3-SPACER K-B191...
Page 69 OIL-1 FRU-K3-OIL CUP K-B109 FRU-K3-KEY 3x3x20L K-B17-1 FRU-K3-WORM GEAR SET SCREW M6-P1.0x8L K-B88-1 FRU-K3-COMPRESSION SPRING K-B89 FRU-K3-OVERLOAD CLUTCH LEVER SPRING PLUNGER 20779-3 QUILL PINION SHAFT ASSY-R8 K-B167 FRU-K3-KEY 5x5x25L K-B27-1 FRU-K3-SET SCREW M6-P1.0x8L K-B41 FRU-K3-NEEDLE BEARING BA66 BEARING SIZE KO-BA66Z K-B192 FRU-K3-QUILL HOUSING K-B104...
Page 70 Figure 27 - K3 - Worm Gear Cradle & Parts List Item Title K-B17 FRU-K3-WORM GEAR CRADLE K-B07 FRU-K3-WORM GEAR SPACER K-B08 FRU-K3-FEED DRIVEWORM GEAR K-B05 FRU-K3-WORM CRADLE BUSHING K-B04 FRU-K3-FEED WORM GEAR SHAFT SLEEVE K-B09 FRU-K3-FEED DRIVE WORM GEAR SHAFT K-B11 FRU-K3-KEY 3x3x25L K-B10...
Page 71 Figure 28 - K3 - Quill Feed Selector & Parts List Item Title K-B66 FRU-K3-CLUSTER GEAR COVER K-B64 FRU-K3-CLUSTER GEAR SHAFT CRANK K-B70 FRU-K3-SHIFT CRANK K-B69 FRU-K3-SPRING Ø 3 x 20L K-B68 FRU-K3-GEAR SHIFT PLUNGER K-B72 FRU-K3-SHIFT KNOB-5/16-18NC K-B71 FRU-K3-ROLL PIN Ø 3 x 20L K-B63 FRU-K3-FEED GEAR SHIFT FORK K-B65...
Page 72 Figure 29 - K3 - Quill Pinion Shaft & Parts List Item Title UseAs K-B166 QUILL PINION SHAFT 25706 BUSHING KIT-PINION SHAFT-R8 K-B91 WASHER K-B92 OVERLOAD CLUTCH WORM GEAR K-B93 OVERLOAD CLUTCH RING K-B92-1 SCREW SOC HD CAP M4-P0.7x15L K-B94 SNAP RING 95 DOWEL PIN Ø...
Page 73 Figure 30 - K3 - Overload Clutch Trip & Parts List Item Title K-B81 FRU-K3-OVERLOAD CLUTCH SLEEVE K-B81-1 FRU-K3-KEY 5x8x13L K-B80 FRU-K3-OVERLOAD CLUTCH K-B79 FRU-K3-SAFETY CLUTCH SPRING K-B78 FRU-K3-OVERLOAD CLUTCH LOCKNUT K-B76 FRU-K3-SOCKET SET SCREW M6-P1.0x8L K-B75 FRU-K3-CLUTCH RING K-B97 FRU-K3-OVERLOAD CLUTCH WASHER K-B98 FRU-K3-SNAP RING Ø...
Page 74 Figure 31 - K3 - Feed Reverse Clutch & Parts List Item Title K-B57 FRU-K3-FEED WORM SHAFT K-B47 FRU-K3-FEED WORM SHAFT THRUST WASHER K-B44 FRU-K3-FEED WORM SHAFT BUSHING K-B43 FRU-K3-WORM K-B59 FRU-K3-PIN Ø 3x12L K-B49 FRU-K3-FEED REVERSE BEVEL GEAR K-B48 FRU-K3-BUSHING K-B62 FRU-K3-KEY 3x3x15L...
Page 75 Figure 32 - K3 - Spindle Assembly & Parts List Item Title K-B127 SPINDLE R8 K-B134 SPINDLE DIRT SHIELD 20838 BEARING-ANGULAR CONTACT-U/SET(2)-7207 P4 K-B136 BEARING SPACER-SMALL K-B137 BEARING SPACER-LARGE K-B133 NOSE-PIECE K-B132 SLEEVE K-B131 BEARING-DEEP GROVE-6206ZZ K-B130 BEARING LOCK WASHER Ø 30 K-B129 SPINDLE BEARING LOCK NUT- Ø30-20N K-B150-1...
Page 76 Figure 33 - K3 Base Machine Southwestern Industries, Inc. ProtoTRAK KMX K3 & Retrofit Safety, Installation, Maintenance, Service & Parts List Manual...
Page 77 Parts List – K3 Base Machine (Reference Only)(Figure 33) Item Title FRU-K3-QUILL HOUSING ADJ.GEAR FRU-K3-RAM ADAPTER FRU-K3-NUT FRU-K3-VERTICAL ADJUSTING WORM FRU-K3-WORM THRUST WASHER(2REQ.) FRU-K3-VERTICAL ADJUSTING WORM SHAFT FRU-K3-WORM KEY FRU-K3-RAM FRU-K3-SOCKET CAP SCREW(2REQ.) FRU-K3-ROLL DOWEL PIN FRU-K3-ANGLE PLATE FRU-K3-ROUND HD DRIVE SCREW(5REQ.) FRU-K3-ADAPTER PIVOT PIN FRU-K3-CHAMFERED &...
Page 78 C58-1 WIPER-CHIP-RIGHT KNEE-K3 FRU-K3-CHIP GUARDS-UPPER FRU-K3-CHIP GUARDS-MIDDLE FRU-K3-CHIP GUARDS-LOWER FRU-K3-KNEE FRU-K3-STOP SCREW FRU-K3-KNEE LOCK SHAFT ASSEMBLY FRU-K3-KNEE LOCK PLUNGER FRU-K3-KNEE BINDER PLUG(PLASTIC) FRU-K3-DOG POINT SET SCREW FRU-K3-SET SCREW FRU-K3-JAM NUT FRU-K3-KEY FRU-K3-WASHER FRU-K3-BEVEL GEAR FRU-K3-SEALED BALL BEARING FRU-K3-BEARING RETAINER RING FRU-K3-SOCKET HEAD CAP SCREW FRU-K3-ELEVATING SCREW ASSEMBLY FRU-K3-HANDLE...
Page 79 C120 FRU-K3-RAM PINION C121 FRU-K3-RAM PINION HANDLE C122 FRU-K3-PLASTIC BALL C123 FRU-K3-CHAMFERED HARDENED WASHER C124 FRU-K3-TURRET C125 FRU-K3-GIB SCREW NUT C126 FRU-K3-GIB SCREW C127 FRU-K3-LOCK BAR C128 FRU-K3-SCREW C129 FRU-K3-LOCKING BOLT C130 FRU-K3-RAM PINION SCREW C131 FRU-K3-RAM/TURRET GIB 20851 FRU-SK2/SK3-STOP PIECE T-BOLT ASSY 20852 FRU-SK2/SK3-TABLE LOCK HANDLE 20853...
Page 80 Figure 34 - K3 - Transformer Option 220V &440V Southwestern Industries, Inc. ProtoTRAK KMX K3 & Retrofit Safety, Installation, Maintenance, Service & Parts List Manual...
Page 81 Figure 35 - K3 -Transformer Options 220V & Southwestern Industries, Inc. ProtoTRAK KMX K3 & Retrofit Safety, Installation, Maintenance, Service & Parts List Manual...
Page 82 Parts List - K3 - Transformer Options Item Title 23430-M0D SAFETY SWITCH - 30A - 600VAC - MODIFIED 23440-220 ENCLOSURE ASSY-TRANSFORMER OPTION-220V 23440-440 ENCLOSURE ASSY-TRANSFORMER OPTION-440V 23454-3 CABLE ASSY-SAFETY SWITCH/XFMR MODULE-DPM 5/16-18X1/2 25B SCREW-SHCS-STL-BO 5/16 70B FLAT WASHER 5/16 M6-1.0X20 25B SCREW-SHCS-STL-BO M6 70B WASHER-FLAT USS-STL-BO...
Page 83: Drawings
Drawings 29819 SYSTEM DIAGRAM-KMX NEW MACHINES & UPGRADES 29756-1 PENDANT ARM KIT-TOP MOUNT-KMX-K3 29756-4 PENDANT ARM KIT-TOP MOUNT-KMX RETROFIT 20255-XX DRIVE KIT – X-AXIS-SM 20255-1 PARTS LIST FOR DRIVE KIT – X-AXIS-SM 23083-XX DRIVE KIT-SPORT – Y-AXIS 23083-1 PARTS LIST FOR DRIVE KIT-SPORT - Y-AXIS 28092-1 BRACKET ASSY-BP SER I Z AXIS - SWI GS 20586-1...
Page 84 REVISIONS REVISIONS NOTICE: THIS DESIGN WAS ORIGINATED BY AND EMBODIES A CONFIDENTIAL PROPRIETARY DESIGN OWNED BY SOUTHWESTERN INDUSTRIES. IT IS DISCLOSED IN CONFIDENCE FOR A SPECIFIC PURPOSE DESCRIPTION DESCRIPTION DATE DATE DPM3/DPM5 UPGRADE WITH CABLE BREAKOUT BOX AND THE RECIPIENT HEREOF AGREES NOT TO MAKE ANY REPRODUCTION, DISCLOSURE OR OTHER USE PRODUCTION RELEASE 14578 10/28/16...
Page 85 REVISIONS REVISIONS NOTICE: THIS DESIGN WAS ORIGINATED BY AND EMBODIES A CONFIDENTIAL PROPRIETARY DESIGN OWNED BY SOUTHWESTERN INDUSTRIES. IT IS DISCLOSED IN CONFIDENCE FOR A SPECIFIC PURPOSE DESCRIPTION DESCRIPTION DATE DATE DPM3 UPGRADE NO CABLE BREAKOUT BOX AND THE RECIPIENT HEREOF AGREES NOT TO MAKE ANY REPRODUCTION, DISCLOSURE OR OTHER USE PRODUCTION RELEASE 14578 10/28/16...
Page 86 REVISIONS REVISIONS NOTICE: THIS DESIGN WAS ORIGINATED BY AND EMBODIES A CONFIDENTIAL PROPRIETARY DESIGN TRM,B3/B5 UPGRADE OWNED BY SOUTHWESTERN INDUSTRIES. IT IS DISCLOSED IN CONFIDENCE FOR A SPECIFIC PURPOSE DESCRIPTION DESCRIPTION DATE DATE AND THE RECIPIENT HEREOF AGREES NOT TO MAKE ANY REPRODUCTION, DISCLOSURE OR OTHER USE PRODUCTION RELEASE 14578 10/28/16...
Page 87 REVISIONS REVISIONS NOTICE: THIS DESIGN WAS ORIGINATED BY AND EMBODIES A CONFIDENTIAL PROPRIETARY DESIGN TRM,B3 UPGRADE OWNED BY SOUTHWESTERN INDUSTRIES. IT IS DISCLOSED IN CONFIDENCE FOR A SPECIFIC PURPOSE DESCRIPTION DESCRIPTION DATE DATE AND THE RECIPIENT HEREOF AGREES NOT TO MAKE ANY REPRODUCTION, DISCLOSURE OR OTHER USE PRODUCTION RELEASE 14578 10/28/16...
Page 88 REVISIONS REVISIONS NOTICE: THIS DESIGN WAS ORIGINATED BY AND EMBODIES A CONFIDENTIAL PROPRIETARY DESIGN OWNED BY SOUTHWESTERN INDUSTRIES. IT IS DISCLOSED IN CONFIDENCE FOR A SPECIFIC PURPOSE DESCRIPTION DESCRIPTION DATE DATE AND THE RECIPIENT HEREOF AGREES NOT TO MAKE ANY REPRODUCTION, DISCLOSURE OR OTHER USE PRODUCTION RELEASE 14578 10/28/16...
Page 89 REVISIONS REVISIONS NOTICE: THIS DESIGN WAS ORIGINATED BY AND EMBODIES A CONFIDENTIAL PROPRIETARY DESIGN OWNED BY SOUTHWESTERN INDUSTRIES. IT IS DISCLOSED IN CONFIDENCE FOR A SPECIFIC PURPOSE DESCRIPTION DESCRIPTION DATE DATE AND THE RECIPIENT HEREOF AGREES NOT TO MAKE ANY REPRODUCTION, DISCLOSURE OR OTHER USE PRODUCTION RELEASE 14578 10/28/16...
Page 90 REVISIONS NOTICE: THIS DESIGN WAS ORIGINATED BY AND EMBODIES A CONFIDENTIAL PROPRIETARY DESIGN OWNED BY SOUTHWESTERN INDUSTRIES. IT IS DISCLOSED IN CONFIDENCE FOR A SPECIFIC PURPOSE DESCRIPTION DATE AND THE RECIPIENT HEREOF AGREES NOT TO MAKE ANY REPRODUCTION, DISCLOSURE OR OTHER USE PRODUCTION RELEASE 14570 09/07/16 OF THIS INFORMATION WITHOUT THE WRITTEN CONSENT OF SOUTHWESTERN INDUSTRIES.
Page 91 Printed 1/31/2017 Parts List for Assembly P/N: 29756-1 29756-1 Type Dwg Size PENDANT ARM KIT-TOP MOUNT-KMX, K3 Revision Product Status Engineer Date 4/20/2016 Planner Code Comm Code Item Title Detail UseAs Stat Type Mfr 29775-3 PENDANT ARM ASSY-KMX 15896 CAP-PENDANT 16797 RAM SUPPORT MACHINED 16919...
Page 92 REVISIONS NOTICE: THIS DESIGN WAS ORIGINATED BY AND EMBODIES A CONFIDENTIAL PROPRIETARY DESIGN OWNED BY SOUTHWESTERN INDUSTRIES. IT IS DISCLOSED IN CONFIDENCE FOR A SPECIFIC PURPOSE DESCRIPTION DATE AND THE RECIPIENT HEREOF AGREES NOT TO MAKE ANY REPRODUCTION, DISCLOSURE OR OTHER USE PRODUCTION RELEASE 14570 09/07/16 OF THIS INFORMATION WITHOUT THE WRITTEN CONSENT OF SOUTHWESTERN INDUSTRIES.
Page 93 Printed 1/31/2017 Parts List for Assembly P/N: 29756-4 29756-4 Type Dwg Size PENDANT ARM KIT-TOP MOUNT-KMX RETROFIT Revision Product Status Engineer Date 4/20/2016 Planner Code Comm Code Item Title Detail UseAs Stat Type Mfr 29775-3 PENDANT ARM ASSY-KMX 15896 CAP-PENDANT 16797 RAM SUPPORT MACHINED 16919...
Page 94 Parts List for Assembly P/N: 29756-4 29756-4 PENDANT ARM KIT-TOP MOUNT-KMX RETROFIT Rev C Printed 1/31/2017 Item Title Detail UseAs Stat Type Mfr 24009-3 WASHER-BELLEVILLE SPRING LK-SERRATED .264 ID x .374 OD x .024 THK-1/4 or M6 M6 70B WASHER-FLAT USS-STL-BO 21969 WASHER-BELLEVILLE SPRING LK .630 ID x 1.875 OD x...
Page 95 NOTICE: THIS DESIGN WAS ORIGINATED BY AND EMBODIES A REVISIONS CONFIDENTIAL PROPRIETARY DESIGN OWNED BY SOUTH- WESTERN INDUSTRIES. IT IS DISCLOSED IN CONFIDENCE FOR DESCRIPTION DATE APPRV A SPECIFIC PURPOSE AND THE RECIPIENT HEREOF AGREES BEARING HOUSING NOT TO MAKE ANY REPRODUCTION, DISCLOSURE OR OTHER ITEM 8 REF WAS: 9.
Page 96 Printed 12/21/2015 Parts List for Assembly P/N: 20255-1 20255-1 Type Dwg Size DRIVE KIT-X AXIS SM Revision Product Status Engineer Date 6/19/1996 Planner Code SIGN DATE 14335 12/5/14 Comm Code MANUF 14468 12.21.15 Item P/N Title Detail Qty UseAs Rev Stat Type 15621 DRIVE HOUSING R DWG...
Page 97 Parts List for Assembly P/N: 20255-1 20255-1 DRIVE KIT-X AXIS SM Rev J Printed 12/21/2015 Item P/N Title Detail Qty UseAs Rev Stat Type 8-32X3/8 20B SCREW-RH-PHIL-STL-BO 10-32X3/4 25B SCREW-SHCS-STL-BO 1/2-20 51Z NUT-HEX JAM-STL-ZINC 15759 WASHER-1/4 HARD BLK OX 1/8 THK R DWG 3/8 70P WASHER-FLAT USS-STL-BO...
Page 98 NOTICE: THIS DESIGN WAS ORIGINATED BY AND EMBODIES A REVISIONS CONFIDENTIAL PROPRIETARY DESIGN OWNED BY SOUTH- WESTERN INDUSTRIES. IT IS DISCLOSED IN CONFIDENCE FOR DESCRIPTION DATE APPRV A SPECIFIC PURPOSE AND THE RECIPIENT HEREOF AGREES NOT TO MAKE ANY REPRODUCTION, DISCLOSURE OR OTHER ITEM: 4 REF WAS: 3 13602 04/14/10 USE OF THIS INFORMATION WITHOUT THE WRITTEN CON-...
Page 99 Printed 12/5/2014 Parts List for Assembly P/N: 23083-1 23083-1 Type Dwg Size DRIVE KIT-PT4-Y AXIS Revision Product Status Engineer Date 11/19/2001 Planner Code DATE SIGN 13200 1.22.07 Comm Code MANUF 13602 02/03/10 14335 12/5/14 Item P/N Title Detail Qty UseAs Rev Stat Type Mfr Mfr P/N 15626 SEAL-BEARING HOUSING...
Page 100 Parts List for Assembly P/N: 23083-1 23083-1 DRIVE KIT-PT4-Y AXIS Rev J Printed 12/5/2014 Item P/N Title Detail Qty UseAs Rev Stat Type Mfr Mfr P/N 15759 WASHER-1/4 HARD BLK OX 1/8 THK 6-32X3/8 10B SCREW-PH-PHIL-STL-BO 23141 SHEET METAL ASSY-MOTOR COVER-COOLANT 10-32X1 25B SCREW-SHCS-STL-BO 10 73B...
Page 101 REVISIONS NOTICE: THIS DESIGN WAS ORIGINATED BY AND EMBODIES A CONFIDENTIAL PROPRIETARY DESIGN OWNED BY SOUTH- WESTERN INDUSTRIES. IT IS DISCLOSED IN CONFIDENCE FOR DESCRIPTION DATE APPRV A SPECIFIC PURPOSE AND THE RECIPIENT HEREOF AGREES ORIGINAL RELEASE 14158 1.17.14 NOT TO MAKE ANY REPRODUCTION, DISCLOSURE OR OTHER USE OF THIS INFORMATION WITHOUT THE WRITTEN CON- ADDED: ITEMS 10 &...
Page 102 Printed 7/7/2014 Parts List for Assembly P/N: 28092-1 28092-1 Type Dwg Size BRACKET ASSY-BP SER I Z AXIS-SWI GS Revision Product REPLACES 22808-1, BP SER I Status Engineer Date 5/7/2013 Planner Code Comm Code SCALES Item P/N Title Detail UseAs Rev Stat Type Mfr P/N...
Page 103 NOTICE: THIS DESIGN WAS ORIGINATED BY AND EMBODIES A REVISIONS CONFIDENTIAL PROPRIETARY DESIGN OWNED BY SOUTH- WESTERN INDUSTRIES. IT IS DISCLOSED IN CONFIDENCE FOR DESCRIPTION DATE APPRV A SPECIFIC PURPOSE AND THE RECIPIENT HEREOF AGREES ORIGINAL RELEASE 14001 6.15.12 NOT TO MAKE ANY REPRODUCTION, DISCLOSURE OR OTHER USE OF THIS INFORMATION WITHOUT THE WRITTEN CON- SENT OF SOUTHWESTERN INDUSTRIES.
Page 104 Printed 1/23/2015 Parts List for Assembly P/N: 20586-1 20586-1 Type Dwg Size BRACKET ASSY-Z AXIS-EASSON GLASS SCALE Revision Product Status Engineer Date 7/6/2012 Planner Code Comm Code MANUF Item P/N Title Detail Qty UseAs Rev Stat Type Mfr Mfr P/N 20550 PLATE-MOUNTING-Z-AXIS ARM 20551-1...
Page 105 NOTICE: THIS DESIGN WAS ORIGINATED BY AND EMBODIES A REVISIONS CONFIDENTIAL PROPRIETARY DESIGN OWNED BY SOUTH- WESTERN INDUSTRIES. IT IS DISCLOSED IN CONFIDENCE FOR ZONE DESCRIPTION DATE APPRV A SPECIFIC PURPOSE AND THE RECIPIENT HEREOF AGREES NOT TO MAKE ANY REPRODUCTION, DISCLOSURE OR OTHER ORIGINAL RELEASE 12824 12-22-04 USE OF THIS INFORMATION WITHOUT THE WRITTEN CON-...
Page 106 Printed 1/20/2005 Parts List for Assembly P/N: 16208-1 16208-1 Type Dwg Size HARDWARE KIT MX3 Z-AXIS-BP Revision Product Status Engineer Date 4/27/1993 Part Type REVECNDATESIGN A104218/25/93SPG Comm Code MANUF B1047111/30/93FM C104791/6/94SPG D105475/4/94SPG E105868/2/94SPG 12842 1-20-05 Item P/N Title Detail Mfr P/N UseAs 16215 BRACKET BALLNUT-MACHINED (FORK)
Page 107 Parts List for Assembly P/N: 16208-1 16208-1 HARDWARE KIT MX3 Z-AXIS-BP Rev F Printed 1/20/2005 Item P/N Title Detail Mfr P/N UseAs 1/4-20X1 1/4 25B SCREW-SHCS-STL-BO SOUTHWESTERN INDUSTRIES, INC. 16208-1 2615 HOMESTEAD PLACE, RANCHO DOMINGUEZ, CA. 90220 Page 2 of 1-310-608-4422 Fax 1-310-764-2668...
Page 108 NOTICE: THIS DESIGN WAS ORIGINATED BY AND EMBODIES A REVISIONS CONFIDENTIAL PROPRIETARY DESIGN OWNED BY SOUTH- WESTERN INDUSTRIES. IT IS DISCLOSED IN CONFIDENCE FOR DESCRIPTION DATE APPRV A SPECIFIC PURPOSE AND THE RECIPIENT HEREOF AGREES NOT TO MAKE ANY REPRODUCTION, DISCLOSURE OR OTHER ADDED NOTE 1 13091 5/22/06...
Page 109 NOTICE: THIS DESIGN WAS ORIGINATED BY AND EMBODIES A REVISIONS CONFIDENTIAL PROPRIETARY DESIGN OWNED BY SOUTH- WESTERN INDUSTRIES. IT IS DISCLOSED IN CONFIDENCE FOR DESCRIPTION DATE APPRV A SPECIFIC PURPOSE AND THE RECIPIENT HEREOF AGREES NOT TO MAKE ANY REPRODUCTION, DISCLOSURE OR OTHER ADDED NOTE 1 13091 5/22/06...
Page 110 Printed 6/29/2017 Parts List for Assembly P/N: 24230-6 24230-6 Type Dwg Size Z AXIS BALLSCREW-BASEPLATE-BEARING Revision Product Z AXIS HOUSING & COVERS ASSY Status Engineer Date 4/3/2017 Planner Code DATE 14655 06/28/17 Comm Code Item P/N Title Detail UseAs Rev Stat Type Mfr Mfr P/N 24217 BRACKET-SERVO MOTOR...
Page 111 REVISIONS NOTICE: THIS DESIGN WAS ORIGINATED BY AND EMBODIES A CONFIDENTIAL PROPRIETARY DESIGN OWNED BY SOUTH- DESCRIPTION DATE APPRV WESTERN INDUSTRIES. IT IS DISCLOSED IN CONFIDENCE FOR A SPECIFIC PURPOSE AND THE RECIPIENT HEREOF AGREES ORIGINAL RELEASE 12653 3-25-04 NOT TO MAKE ANY REPRODUCTION, DISCLOSURE OR OTHER USE OF THIS INFORMATION WITHOUT THE WRITTEN CON- ADD ITEM 11:23891-DOC 12826 12-20-04...
Page 112 ALL PARTS TO BE REMOVED FOR INSTALLATION OF ELECTRONIC 10 3X REF HANDWHEEL OPTION ELECTRONIC HANDWHEEL OPT KNEE MILL Y - AXIS STANDARD KNEE MILL Y - AXIS 11. INSTALL OPTION PER DRAWING. FOR PARTS LIST SEE SEPARATE "A" SIZE SHEET 12 RETURN TO STOCK: 15616 (HANDWHEEL ASSY).
Page 113 Printed 4/10/2017 Parts List for Assembly P/N: 23891 23891 Type Dwg Size ELECTRONIC HANDWHEEL KIT-KNEE MILL-X & Y Revision Product K-MILL AXIS Status Engineer Date 1/30/2004 Planner Code Comm Code Item Title Detail UseAs Stat Type Mfr 21946 ELEC HANDWHEEL-X & Y AXIS 21992-1 BUSHING - BALL SCREW 1.125 LG.
Page 114 Parts List for Assembly P/N: 23891 23891 ELECTRONIC HANDWHEEL KIT-KNEE MILL-X & Y AXIS Rev H Printed 4/10/2017 Item Title Detail UseAs Stat Type Mfr 22768-37 LABEL-TEXT-WHITE-1.00W x 1.437H EHW Y SOUTHWESTERN INDUSTRIES, INC. 23891 2615 HOMESTEAD PLACE, RANCHO DOMINGUEZ, CA. 90220 Page 2 of 1-310-608-4422 Fax 1-310-764-2668...
Page 115 REVISIONS DESCRIPTION DATE APPRV ITEM 2 WAS: 26987; ITEM 3 WAS: 22605. 14653 4.10.17 Left Side NOTE 1 WAS: WASHERS (ITEMS 11 & 12)MAY BE SWAPPED IN ORDER TO OBTAIN THE REQUIRED SHOULDER HEIGHT. 14695 07/31/17 of DPM2: ADDED ITEM 13. ADDED PICTORIALS FOR DPM2, ADDED SH3 14824 03/26/18 TITLE WAS:"...OPTION-K2,K3-R8"...
Page 116 Printed 3/26/2018 Parts List for Assembly P/N: 22580-7 22580-7 Type Dwg Size POWER DRAWBAR OPTION -K2,K3.DPM2-R8 Revision Product PT4,5,10 Status Engineer Date 10/27/2000 Planner Code Comm Code NONE Item P/N Title Detail Reference(t) UseAs Rev Stat Type 22581 POWER DRAW BAR-TORQUE RITE 26987-1 DRAWBAR-K2/K3-R8 27007...
Page 117 NOTICE: THIS DESIGN WAS ORIGINATED BY AND EMBODIES A REVISIONS CONFIDENTIAL PROPRIETARY DESIGN OWNED BY SOUTH- WESTERN INDUSTRIES. IT IS DISCLOSED IN CONFIDENCE FOR DESCRIPTION DATE APPRV A SPECIFIC PURPOSE AND THE RECIPIENT HEREOF AGREES ITEM 12: 22647-2 WAS 22647-4 12052 4/26/01 NOT TO MAKE ANY REPRODUCTION, DISCLOSURE OR OTHER...
Page 118 Printed 5/9/2017 Parts List for Assembly P/N: 22380-1 22380-1 Type Dwg Size AIR REGULATOR ASSY-DPMV-FILTER Revision Product Status Engineer Date 7/26/2000 Planner Code Comm Code KIT-MISC Item Title Detail UseAs Stat Type Mfr 22378 MANIFOLD-PT4 AIR 22607 FILTER/REGULATOR-PT4 22644-4 PLUG-1/4 NPT HEX SOCKET 22645-4 NIPPLE-1/4 NPT x 1.37 LG 22646-4...
Page 119 TRAK Machine Tools Southwestern Industries, Inc TRAK Warranty Policy Warranty TRAK products are warranted to the original purchaser to be free from defects in workmanship and materials for the following periods: Product Warranty Period Materials Factory Labor 1 Year 1 Year...

TRAK ProtoTRAK KMX K3 Safety, Installation, Maintenance, Service & Parts List Manual

2 Installation

3 Troubleshooting by Symptom

4 Service Codes

5 Maintenance

6 Introduction to Self-Service

7 Figures and Parts Lists

8 Drawings

Quick Links

Troubleshooting

Need help?

Questions and answers

Related Manuals for TRAK ProtoTRAK KMX K3

Summary of Contents for TRAK ProtoTRAK KMX K3

Table of Contents