Specifications - Audio Technica MicroSet BP892 Quick Start Manual

remove the element cover and place it out of harm's way. Gently slide the
moisture guard over the element. Replace the element cover.
Avoid leaving the microphone in the open sun or in areas where
temperatures exceed 110° F (43° C) for extended periods. Extremely high
humidity should also be avoided.
Architect's and Engineer's Specifications
The microphone shall be a fixed-charge condenser designed for headworn
use. It shall have an omnidirectional polar pattern and a frequency response
of 20 Hz to 20,000 Hz. The microphone shall operate from an external 11V
to 52V DC phantom power source. It shall be capable of handling sound
input levels up to 135 dB with a dynamic range of 104 dB. Nominal open-
circuit output voltage shall be 3.5 mV at 1V, 1 Pascal. Output shall be low
impedance balanced (250 ohms). The microphone shall be RoHS compliant.
The microphone shall have a 1.4 m (55") permanently attached miniature
cable terminating in a locking 4-pin output connector. The output connector
shall connect to a jack on the included power module. The output connector
shall also connect to any Audio-Technica UniPak
transmitter. The power module shall contain a recessed switch to permit
choice of flat response or 80 Hz low-frequency roll-off. The output of the
power module shall be a 3-pin XLRM-type connector.
The microphone shall be an underear headworn design with a diameter of
2.6 mm (0.10"). Microphone, boom and earpiece weight shall be 2.6 grams
(0.09 oz). The microphone shall include a power module, a cable clip, two
windscreens, two element covers, a moisture guard, a belt clip and a carrying
case. Finish shall be low-reflectance black [beige].
Wireless models of the microphone shall also be available, terminated for
use with Audio-Technica UniPak
other manufacturers' wireless systems. The wireless models' dimensions,
polar pattern and included accessories (excluding power module and belt
clip) shall be identical to those of the wired model. The microphone shall
also be available unterminated.
The Audio-Technica BP892 [BP892-TH] is specified.
The Audio-Technica BP892cW [BP892cW-TH]; BP892cL4 [BP892cL4-TH];
BP892cLM3 [BP892cLM3-TH]; BP892cT4 [BP892cT4-TH]; BP892cT5
[BP892cT5-TH] (wireless version) is specified.
The Audio-Technica BP892c [BP892c-TH] (unterminated) is specified.
BP892, cW, cW-TH
Function Wire Color
Pin 1
Pin 1 Ground/Shield Green
Pin 2
Pin 2 Instrument Jumper to Pin 1
Pin 3
Pin 3 Mic Audio Copper Color
Pin 4
Pin 4 Bias + In Red
cLM3, cLM3-TH
Function Wire Color
Sleeve Ground/Shield Green
Ring Mic Audio Copper Color
Tip Bias + In Red
body-pack wireless
®
® body-pack transmitters and a variety of
cT4, cT4-TH cT5, cT5-TH
Function Wire Color Function
Ground/Shield Green Pin 1 Ground/Shield
Bias + In Red Pin 2 Bias + In
Mic Audio Copper Color Pin 3 Mic Audio
Source Load Jumper to Pin 3 Pin 4 Source Load
Pin 5 Line In
cL4, cL4-TH
Function Wire Color
Pin 1 N/C Open
Pin 2 N/C Open
Pin 3 Bias + In, Red
Mic Audio
Shell/Case Ground/Shield Green

Specifications

Frequency response
Low frequency roll-off
Open circuit sensitivity
Maximum input sound level
Dynamic range (typical)
Signal-to-noise ratio
Phantom power requirements
Current Consumption
Output connector (power module)
Audio-Technica case style
Accessories furnished
In the interest of standards development, A.T.U.S.
offers full details on its test methods to other industry
1 Pascal = 10 dynes/cm
Typical, A-weighted, using Audio Precision System One.
1
Specifications are subject to change without notice.
frequency response: 20 – 20,000 Hz
Wire Color
Green
Red
Copper Color
Jumper to Pin 1
50 100 200 500
Open
Frequency in Hertz
LEGEND 12" or more on axis
Roll-off
0˚
330˚ 30˚
300˚
270˚
240˚
150˚
210˚
180˚
SCALE IS 5 DECIBELS PER DIVISION
Audio-Technica U.S., Inc., 1221 Commerce Drive, Stow, Ohio 44224
Audio-Technica Limited, Old Lane, Leeds LS11 8AG England
©2009 Audio-Technica U.S., Inc. audio-technica.com
BP892 & BP892-TH
Element
Fixed-charge back plate, permanently
polarized condenser
Polar pattern Omnidirectional
20-20,000 Hz
80 Hz, 18 dB/octave (wired only)
–49 dB (3.5 mV) re 1V at 1 Pa
Impedance
250 ohms (wired only)
135 dB SPL, 1 kHz at 3% T.H.D.
104 dB, 1 kHz at Max SPL (wired only)
63 dB, 1 kHz at 1 Pa
1
11-52V DC, 2 mA typical (wired only)
0.1 mA typical at 5V (wireless only)
Voltage Range 2.5-11V (wireless only)
Switch Flat, roll-off (wired only)
Weight Microphone, boom & earpiece:
2.6 g (0.09 oz)
Power module (wired only): 85 g (3.0 oz)
Dimensions Microphone: 8.1 mm (0.32") long,
2.6 mm (0.10") diameter
Boom: 98.4 mm (3.87") long,
1.07 mm (0.04") diameter
Power module (wired only): 97.6 mm
(3.84") long, 18.9 mm (0.74") diameter
Integral 3-pin XLRM-type
Cable 1.4 m (55") long (permanently attached
to microphone), 1.6 mm (0.06") diameter,
2-conductor shielded cable with locking
4-pin connector (wired only)
M31
BP892
AT8539 power module (wired only);
AT8440 cable clip; two AT8157
windscreens; two AT8156 element
covers; moisture guard; belt clip (wired
only); carrying case
BP892-TH
AT8539 power module (wired only);
AT8440 cable clip; two AT8157-TH
windscreens; two AT8156-TH element
covers; moisture guard; belt clip (wired
only); carrying case
professionals on request.
2 = 10 microbars = 94 dB SPL
LEGEND
polar pattern
300˚
10 dB
270˚
1k 2k 5k 10k 20k
240˚
SCALE IS 5 DECIBELS PER DIVISION
60˚
90˚
120˚
LEGEND
200 Hz
1 kHz
5 kHz
8 kHz
10 dB
50 100 200 500 1k 2k 5k 10k 20k
Frequency in Hertz
12" or more on axis
Roll-off
0˚
330˚ 30˚
60˚
90˚
120˚
LEGEND
200 Hz
150˚
210˚
1 kHz
180˚
5 kHz
8 kHz
0001-0162-00