Table of Contents
Advertisement
sg82 amend p8.qxd
19/01/00
12:35
Page 1
®
SG85
OPERATING INSTRUCTIONS
Thank you for purchasing the Earlex SG85 Electric Airless Spray Gun,
this is a highly versatile spray gun and can be used
for a variety of applications.
BEFORE USE - PLEASE READ THE SAFETY
& OPERATING INSTRUCTIONS
Please retain for future reference
Advertisement
Table of Contents
Related Manuals for Earlex Super Sprayer 85 SG85
Summary of Contents for Earlex Super Sprayer 85 SG85
-
Page 1: Operating Instructions
Page 1 ® SG85 OPERATING INSTRUCTIONS Thank you for purchasing the Earlex SG85 Electric Airless Spray Gun, this is a highly versatile spray gun and can be used for a variety of applications. BEFORE USE - PLEASE READ THE SAFETY &... - Page 2 Spray Nozzle Suction Tube Paint Container Switch Screw OUTFIT COMPONENTS AND USES Your complete Earlex SG85 Electric Airless Spray Gun outfit includes: Professional sprayer Viscosity test cup, which enables you to test your paint with 0.8mm spray for thickness before painting.
-
Page 3: Please Read Before Use
We have done all we can to ensure that used correctly and according to these instructions, the Earlex SG85 Electric Airless Spray Gun will give long trouble free service. We accept no responsibility for damage caused by the use of incorrect or... - Page 4 sg82 amend p8.qxd 19/01/00 12:35 Page 4 TECHNICAL SPECIFICATION MATERIALS WILL CAUSE PREMATURE WEAR ON THE Power Supply 230V 50Hz-AC PISTON AND WILL VOID YOUR Rated Input 85 Watts GUARANTEE. Pump Output 240g/min(water) Max. Pressure 142 Bar (2000psi) TO OBTAIN THE BEST RESULTS Container Capacity 1.0 Itr FROM YOUR SPRAY GUN Spray Gun weight 1.6 kg...
-
Page 5: Operation
sg82 amend p8.qxd 19/01/00 12:35 Page 5 * These paints cannot be measured in the viscosity cup. To spray them, remove the filter from the suction tube, thin according to manufacturer’s recom- mendations and strain to remove any lumps or particles. Fig 1 Follow the manufacturers guide for thinning inconjunction with a spray... - Page 6 sg82 amend p8.qxd 19/01/00 12:35 Page 6 Adjust the output control knob on up or down 25-30cm (10”-12”) from the back of the gun to control the the surface. Avoid spraying at an volume of paint that you wish to angle as this will lead to runs on the apply (fig 3).
-
Page 7: Helpful Hints
sg82 amend p8.qxd 19/01/00 12:35 Page 7 HELPFUL HINTS 3) If you start spraying and find that the spray pattern is small and 1. Evenly control the speed of splattery and adjusting the output movement of the spray gun. A fast control knob does not solve the speed will give a thin coat and a problem then you need to try the... -
Page 8: Suction Tube
sg82 amend p8.qxd 19/01/00 12:35 Page 8 4) Screw the spray nozzle onto the end over suction tube filter moulding, ensure of the flexible extension. this fits tightly to prevent air leaks, 5) Bend the flexible extension to the immerse filter end of suction tube into required shape. -
Page 9: Priming The Sprayer
sg82 amend p8.qxd 19/01/00 12:35 Page 9 PRIMING THE SPRAYER CLEANING Run solvent through the tube until it If you are using the suction tube, is clean. Then disassemble the you will need to prime the sprayer fittings at both ends before any by removing air from the system. -
Page 10: Maintenance And Repair
This removal or lost. will cause a poor spray pattern and 8) Clean all parts thoroughly. will require replacing. Replacement 9) Lubricate with oil. valves are available from the Earlex 10) Re-assemble in reverse order. Service Department. See fig 9. - Page 11 sg82 amend p8.qxd 19/01/00 12:35 Page 11 You will need to check the spray NEVER DISPOSE OF PAINTS OR nozzles, piston and spring from SOLVENTS INTO DRAINS. time to time to check for wear and CONTACT YOUR LOCAL replace if necessary. COUNCIL TO ARRANGE COLLECTION.
-
Page 12: Troubleshooting
sg82 amend p8.qxd 19/01/00 12:35 Page 12 TROUBLE SHOOTING PROBLEM CAUSE ACTION REQUIRED Spray Gun HUMS Piston Sticking. Remove 4 screws adjacent to paint pick up pipe but does not Part no. SG12. part no. SG14. Release container cover, cylinder operate. - Page 13 sg82 amend p8.qxd 19/01/00 12:35 Page 13 20. Viscosity Cup SG18 Parts and Accessories 21. Switch SG43 1. Spray Nozzle 0.8mm SG44 22. Mains Lead with plug SG79 2. Atomiser Valve SG03 23. Terminal Block SG89 3. Cylinder Housing SG67 24.
- Page 14 OTHER PRODUCTS FROM SC165 - 1500W 4.5 ltr steam EARLEX. cleaning kit: incl. carpet cleaner, window/tile cleaner, jet nozzle Earlex also manufacture a wide cleaner, upholstery cleaner/small range of steam wallpaper strippers. steamplate, large wallpaper Designed to remove all types of stripping plate.
- Page 15 sg82 amend p8.qxd 19/01/00 12:35 Page 15...
- Page 16 01483-454666 EC Declaration of Conformity We declare that the units: SG85 conform to: 73/23/EEC, 89/336/EEC, EN61000-3-2 & EN61000-3-3, EN55014, EN55014-2 Tim Hopper-Technical director Earlex Ltd., Moorfield Road, Slyfield Industrial Estate, Guildford, Surrey, GU1 1RU. ® Tel: 01483-454666. Fax: 01483-454548 email:enquiries@earlex.co.uk...
Need help?
Do you have a question about the Super Sprayer 85 SG85 and is the answer not in the manual?
Questions and answers