Page 1
Draft Version Setup Reference guide for KX-HTS Series (Tested with HTS824 Version 1.6) “LCR” SIP Trunk service with External Router Version 0.1(PSCEU) 29th August, 2017...
Attention: This document was created based on the results of test environment accounts. Panasonic cannot guarantee SIP Trunk operation in all environments, however as a result of completing this Inter-Operability Test Panasonic will provide technical support for any issues experienced an assist as far as possible in providing a resolution.
Page 3
With External Router and Network Example Existing User Network: 192.168.22.0 / Subnet Mask: 255.255.255.0 (/24) Existing Router IP Address: 192.168.22.1, Static DNS: Primary DNS Server 192.168.22.1 / Secondary DNS Server: 8.8.8.8 Internet Existing Router Existing User Network (192.168.22.0 /24) (192.168.22.1/24) To Existing Router...
(2) Network Settings Network Configuration WAN Setting Select [Network Configuration] - [3.WAN] – [1.WAN Setting] and Select [WAN 1 Channel] Click [Modify] HTS WAN-1 IP: 192.168.22.99 (Example) Assigned HTS WAN IP address by user network administrator 1. WAN Type: Fix IP 2.
Page 6
LAN Settings Go to [Network Configuration] - [4.LAN] - [2.LAN Settings] 1. IP Address: 192.168.0.101 2. Subnet Mask: 255.255.255.0 3. DHCP Mode: Server [DHCP server] 4. IP Pool Staring Address: Leave 192.168.0.102 5. IP Pool Ending Address: Leave 192.168.0.254 6.
(3) Trunk Port Attribution Select [PBX Configuration] - [3.Trunk] - [1.Port] and click [Edit / CO Line Number 1 to 8] [CO Line Number 1] 1. Attribution: SIP Carrier - 1 2. Trunk Group: Leave at 1 Click [Apply] Click [Apply Now] Example, Configure “CO-Line 1-2: SIP Carrier-1, Other CO-Line: No Connect”...
(4) Provisioning the SIP Trunk SIP Trunk Property - Common Select [PBX Configuration] - [3.Trunk] - [7. SIP Trunk Property] - [Common] 1. DNS SRV Record Resolve Ability: Leave Disable [Register] 2. Register Sending Interval (s): Leave at 3600 3.
Page 9
SIP Trunk Property continued – SIP Carrier-1 [SIP Carrier-1] 1. Provider Name: Enter a name – reference only 2. SIP Server Name: trunksip2.lcrcom.es 3. SIP Server IP Address: Leave at 0.0.0.0 4. SIP Server port Number: 4399 5. SIP Server Domain: Not required 6.
Page 10
SIP Trunk Property continued – SIP Carrier-1 [Calling Party] 1. Header Type: Leave From Header 2. Host Name: Leave BLANK 3. Format: Leave Without “+” 4. Send CLIP of caller when call from SIP Leave Enable Carrier is forwarded to same SIP carrier: *CLI will be converted to PBX No by LCR [Called Party] 5.
(5) Incoming Call Routing DDI Table [PBX Configuration] - [3.Trunk] - [3.DDI] 1. DDI Number: Enter the DDI number in the format (as below) Example Landline Number: 910 123 001 Enter: 913123001 2. Name: Determined by the installer (optional setting) 3.
(8) Router/Firewall Port Forwarding OPTION message will be sent continuously from LCR, if necessary configure the following. For External router setup, configure Port Forwarding on the router as follows: udp port 5060 – to HTS WAN1 IP address (e.g. 192.168.22.99) udp port range 12000-20000 (RTP) –...