Frontier FiOS-G1100 User Manual

Verizon quantum gateway

Table of Contents

Quick Links

Download this manual

FiOS Quantum Gateway

Model FiOS‐G1100

Verizon

User Guide

Table of Contents

Need help?

Do you have a question about the FiOS-G1100 and is the answer not in the manual?

Questions and answers

Summary of Contents for Frontier FiOS-G1100

Page 1 Verizon FiOS Quantum Gateway User Guide Model FiOS‐G1100 ...
Page 2: Table Of Contents
Contents Chapter 1 Introduction ................... 1 Package Content ...................... 1 System Requirements .................... 1 Features ........................ 1 Getting to Know your Gateway .................. 3 Mount Gateway to Wall Option .................... 5 Chapter 2 Connecting your Gateway .............. 7 Setting Up your Gateway .................... 7 Step 1: Connect your Gateway .................... 7 Step 2: Connect Your Device to your Gateway ................. 8 Step 3: Configure your Gateway .................... 8 Computer Network Configuration ................ 12 Configuring Dynamic IP Addressing .................. 12 Connecting Other Computers and Network Devices .............. 13 Main Screen ....................... 15 Menu ............................ 16 Status ............................ 17 Chapter 3 Wireless Settings ...
Page 3 Chapter 5 Using Network Connections ............ 37 Accessing Network Connections .................. 37 Network (Home/Office) Connection ................ 38 Ethernet/Coax Connection .................. 45 Wireless Access Point Connection ................ 48 Broadband Ethernet/Coax Connection ................. 51 Chapter 6 Configuring Security Settings ............ 57 Firewall ........................ 57 Setting Firewall Configuration .................... 58 Specifying General Settings for IPv4 or IPv6 ................ 59 Access Control ...................... 60 Allow or Restrict Services ...................... 60 Disable Access Control ...................... 61 Port Forwarding ...................... 62 Advanced Port Forwarding Rules .................... 62 Port Triggering ...................... 64 Remote Administration .................... 65 Static NAT ........................ 67 Security Log ........................ 68 Event Types .......................... 69 Chapter 7 Setting Parental Controls.............. 74 ...
Page 4 Routing ........................ 94 IPv6 Configuration Control ...................... 94 Routing Settings ........................ 95 IP Address Distribution ...................... 97 Firmware Upgrade ..................... 1 02 Firmware Upgrade ......................... 102 Firmware Restore ........................ 104 Date and Time ...................... 1 06 Date and Time Settings ...................... 106 Scheduler Rules ........................ 107 Configuration Settings .................... 1 10 Configuration File ........................ 110 System Settings ........................ 111 Ethernet Port Configuration .................... 114 Chapter 9 Monitoring your Gateway ............ 1 16 Gateway Status ...................... 1 16 Advanced Status ...................... 1 17 System Logging ...
Page 5: Chapter 1 Introduction
Chapter 1 Introduction The Verizon FiOS® Quantum Gateway lets you transmit and distribute digital entertainment and information to multiple devices in your home/office. Your Gateway supports networking using coaxial cables, Ethernet, or Wi‐Fi, making it one of the most versatile and powerful gateways available. Package Content Your package contains: • The FiOS Quantum Gateway • Power adapter • WAN Ethernet cable (white) • LAN Ethernet cable (yellow) • Quick Start Guide • Installation Guide System Requirements System and software requirements are: • A computer or other network device supporting Wi‐Fi or wired Ethernet • A web browser, such as Chrome, Firefox, Internet Explorer 8 or higher, or Safari 5.1 or higher Features Your Gateway features include: • Support for multiple networking standards, including WAN – Gigabit Ethernet and MoCA 2.0 interfaces LAN – 802.11 b/g/n/ac, Gigabit Ethernet and MoCA 2.0 interfaces • Integrated wired networking with 4‐port Ethernet switch and MoCA Ethernet supports speeds up to 1000 Mbps MoCA 2.0 and 1.1 enabled to support speeds up to 700 Mbps over coaxial cable Page 1 ...
Page 6 • Integrated wireless networking with 802.11b/g/n/ac access point featuring: 802.11b enabled to support speeds up to 11 Mbps wirelessly 802.11g enabled to support speeds up to 54 Mbps wirelessly 802.11n enabled to support speeds up to 450 Mbps wirelessly 802.11ac enabled to support speeds up to 1300 Mbps wirelessly • Enterprise‐level security, including: Fully customizable firewall with Stateful Packet Inspection (SPI) Content filtering with URL‐keyword based filtering, parental control, and customizable filtering policies per computer Intrusion detection with Denial of Service protection against IP spoofing attacks, scanning attacks, IP fragment overlap exploit, ping of death, and fragmentation attacks Event logging Intrusion detection MAC address filtering Static NAT Port forwarding Port triggering Access control Advanced wireless protection featuring WPA2/, WPA2 Mixed Mode, WEP 64/128 bit encryption, and MAC address filtering ICSA certification • Options, including: DHCP server WAN interface auto‐detection DNS server LAN IP and WAN IP address selection MAC address cloning QoS support (end to end layer 2/3) featuring: Differentiated Services (Diffserv), 802.1p/q prioritization, and pass‐through of WAN‐side DSCPs, Per Hop Behaviors (PHBs), and queuing to LAN‐side devices Remote management and secured remote management using HTTPS Static routing Time zone support Page 2 ...
Page 7: Getting To Know Your Gateway
VPN (VPN pass through only) Port forwarding rules IGMP proxy Security logging of multiple event types Daylight savings time support Getting to Know your Gateway Front Panel The front panel has two lighted indicators and a WPS (Wi‐Fi Protected Setup) button. The Power/Internet light will be on and solid when your Gateway is turned on, connected to the Internet, and functioning normally. The Wireless light will be on when your Gateway Wi‐Fi is turned on. For additional information on the front lights and error indications, refer the Troubleshooting section in this Guide. The WPS button is used to initiate Wi‐Fi Protected Setup. This is an easy way to add WPS capable devices to your wireless network. When WPS is initiated from your Gateway, the wireless light slowly flashes white for up to two minutes, allowing time to complete the WPS pairing process on your wireless client device. When a device begins connecting to your Gateway using WPS, the wireless light rapidly flashes white for a few seconds, then turns solid white as the connection completes. If there is an error during the WPS pairing process, the wireless light flashes red rapidly for two minutes after the error occurs. The WPS button can also be used to reboot the router. To perform a soft reboot, press and hold the WPS button for at least 10 seconds. Page 3 ...
Page 8 Side Panel The side panel of your Gateway has a label that contains important information about your device, including the default settings for the Gateway’s wireless network name (ESSID), wireless password (WPA2 key), local URL for accessing the Gateway’s administrative pages, and Gateway administrator password. Rear Panel The rear panel of your Gateway has 8 ports; MoCA (COAX), Ethernet LAN [4], Ethernet WAN, and USB [2]. The rear panel also includes a DC power jack and a reset button. Page 4 ...
Page 9: Mount Gateway To Wall Option
• USB –provides up to 500 mA at 5 VDC for attached devices. For example, you could charge a cell phone. In the future, with a firmware upgrade, the USB host functionality may be available for other devices, such as external storage and cameras. • Reset button – allows you to reset your Gateway to the factory default settings. To reset the Gateway, press and hold the Reset button for at least three seconds. • Ethernet LAN – connects devices to your Gateway using Ethernet cables to join the local area network (LAN). The four Ethernet LAN ports are 10/100/1000 Mbps auto‐ sensing and can be used with either straight‐through or crossover Ethernet cables. • Ethernet WAN – connects your Gateway to the Internet using an Ethernet cable. • MoCA (COAX) WAN and LAN – connects your Gateway to the Internet and/or to other MoCA devices using a coaxial cable. Warning! The WAN Coax Port is intended for connection to Verizon FiOS only. It must not be connected to any exterior or interior coaxial wires not designated for Verizon FiOS. • Power – connects your Gateway to an electrical wall outlet using the supplied power adapter. Mount Gateway to Wall Option For optimum performance, the FiOS Quantum Gateway is designed to stand in a vertical upright position. Verizon does not recommend wall mounting the FiOS Quantum Gateway. However, if you wish to mount your Gateway, you can purchase a wall mount bracket from the Verizon FiOS Accessories Store at verizon.com/fiosaccessories. If you are replacing an existing Verizon wall mounted router, you do not need to remove the mounting screws from the wall. The mounting screws will fit the existing bracket. To mount your Gateway to a wall: Remove the foot by turning the Gateway upside down and removing the single screw that holds the foot to the Gateway. Slide the foot toward the front of the Gateway and pull the foot from the holes. You may need to wiggle the foot slightly. You may use the wall mount bracket as a template for positioning the Gateway. Mark the mounting holes, then remove the wall mount bracket from the wall. Drill holes for the screw anchors. Insert the screws in the screw anchors, then insert the screw anchors in the ...
Page 10 Place the Gateway on the wall bracket and slide the Gateway forward until it locks in place. To secure the Gateway, attach the bracket to the Gateway using the single screw you removed from the foot. Slide the wall mount bracket with the attached Gateway on the screws, then slide the bracket down until it locks in place. Page 6 ...
Page 11: Chapter 2 Connecting Your Gateway
Chapter 2 Connecting your Gateway Connecting your Gateway and accessing its web‐based Graphical User Interface (GUI) are both simple procedures. Accessing the GUI may vary slightly, depending on your device’s operating system and web browser. Setting Up your Gateway There are three basic steps to setting up your Gateway: Step 1: Connect your Gateway to the Internet Step 2: Connect your network device to your Gateway Step 3: Configure your Gateway Before you begin, if you are replacing an existing Gateway, disconnect it. Remove all old Gateway components, including the power supply. They will not work with your new Gateway. Step 1: Connect your Gateway Remove your Gateway, Ethernet cables, and power adapter from the box. Locate your high‐speed Internet (WAN) outlet. This would be the wall jack installed previously by Verizon. Note the type of jack may be either Ethernet or coaxial. Connect your Gateway to the Internet (WAN). If connecting the WAN using Ethernet, use the supplied white Ethernet cable and plug one end into the white Ethernet WAN port on the back of your Gateway. Plug the other end of the cable into the high‐speed Ethernet wall jack. If connecting the WAN using coaxial cable, locate a coaxial cable and connect one end to the coax port on the back of your Gateway. Connect the other end of the coaxial cable to a coax wall jack. Tighten the coaxial cables by hand until snug. The cables should not require a wrench. Plug the power cord into the power port on the back of your Gateway and then into a power outlet. The Gateway automatically turns on as soon as power is plugged in. Page 7 ...
Page 12: Step 2: Connect Your Device To Your Gateway
IMPORTANT: Wait until the Power/Internet light on the front of the Gateway stops flashing and is solid white. If after several minutes it is still not solidly lit, check the troubleshooting steps in the Troubleshooting section of the user guide. Step 2: Connect Your Device to your Gateway If connecting a device using wired Ethernet (preferred for initial setup): • Plug one end of the supplied yellow Ethernet cable into one of the four yellow Ethernet ports in the back of your Gateway. • Plug the other end of the yellow Ethernet cable into the Ethernet port of your network device. If connecting a wireless device using the wireless network: • Access the Wi‐Fi setting on your wireless device, then select your new Gateway using the wireless network name (ESSID) shown on the sticker located on the side of your Gateway. • Enter the wireless password (WPA2 key) also shown on the sticker. Step 3: Configure your Gateway Open a web browser on the device connected to your Gateway network. In the browser address field (URL), enter: myfiosgateway.com, then press the Enter key on your keyboard. Alternately, you can enter: http://192.168.1.1 Page 8 ...
Page 13 The first time you access your Gateway, an Easy Setup Wizard displays to help step you through the setup process. Click the Get Started button. The Gateway Login screen displays. In the Admin Password field, enter the password that is printed next to the Administrator Password on the label on the side of your Gateway. Page 9 ...
Page 14 Click Next. The Personalize your Gateway screen displays. For your protection, your Gateway is pre‐set at the factory to use WPA2 (Wi‐Fi Protected Access) encryption for your wireless network. This is the best setting for most users and provides maximum security. If you have an old wireless device that does not support WPA2, click the Change button below the Lock icon. This allows you to change the security type to the backwards‐compatible the older, less secure WPA2/WPA mixed mode or WEP encryption, or you can disable wireless security entirely by toggling the WEP option on, then off. WARNING: WEP provides a low level of security and is not recommended. The WEP security setting will drop your Gateway’s wireless speed performance from a maximum data rate of 450 Mbps to a maximum data rate of 54 Mbps. Page 10 ...
Page 15 Click Next to continue and save the Admin and Wi‐Fi changes to your Gateway. IMPORTANT: If you are on a Wi‐Fi device when setting up your Gateway, you will be disconnected from the Wi‐Fi network when you change the Wi‐Fi name or Wi‐Fi password. When this occurs, your Gateway will detect this situation and prompt you to reconnect using the new settings. Save your settings. Once you have personalized your Gateway settings, you will be prompted to save a record of these settings in case you forget them. You have the option to print or save them to a file and save the file on your device. Click Next to continue. Your Gateway verifies the final settings and displays that it is successfully connected to the Internet and is ready for use. Upon the successful completion of setup, the Main screen of the Gateway displays. Your Gateway is now configured. You can change any of the Gateway settings after this initial log in. If your Gateway is subsequently reset to the factory default settings, the settings printed on the label will again be in effect. If your Gateway fails to connect, follow the troubleshooting steps in the Troubleshooting section of this guide. Page 11 ...
Page 16: Computer Network Configuration
Computer Network Configuration Each network interface on your computer should either automatically obtain an IP address from the upstream Network DHCP server (default configuration) or be manually configured with a statically defined IP address and DNS address. We recommend leaving this setting as is. Configuring Dynamic IP Addressing To configure a computer to use dynamic IP addressing: Windows 7 In the Control Panel, locate Network and Internet, then select View Network Status and Tasks. In the View your active networks – Connect or disconnect section, click Local Area Connection in the Connections field. The Local Area Connection Status window displays. Click Properties. The Local Area Connection Properties window displays. Select Internet Protocol Version 4 (TCP/IPv4), then click Properties. The Internet Protocol Version 4 (TCP/IPv4) Properties window displays. Click the Obtain an IP address automatically radio button. Click the Obtain DNS server address automatically radio button, then click OK. In the Local Area Connection Properties window, click OK to save the settings. To configure Internet Protocol Version 6 (TCP/IPv6) to use dynamic IP addressing, repeat step 1 to 7. However for step 3, select Internet Protocol Version 6 (TCP/IPv6) in the Properties option. Macintosh OS X Click the Apple icon in the top left corner of the desktop. A menu displays. Select System Preferences. The System Preferences window displays. Click Network. Verify that Ethernet, located in the list on the left, is highlighted and displays Connected. Click Assist Me. Follow the instructions in the Network Diagnostics Assistant. Page 12 ...
Page 17: Connecting Other Computers And Network Devices
Connecting Other Computers and Network Devices You can connect your Gateway to other computers or set top boxes using an Ethernet cable, wireless connection (Wi‐Fi), or coaxial cable. Ethernet Plug one end of an Ethernet cable into one of the open yellow Ethernet ports on the back of your Gateway. Plug the other end of the Ethernet cable into an Ethernet port on the computer. Repeat these steps for each computer to be connected to your Gateway using Ethernet. You can connect up to four. Wireless using WPS Wi‐Fi Protected Setup (WPS) is an easier way for many devices to set up a secure wireless network connection. Instead of manually entering passwords or multiple keys on each wireless client, such as a laptop, printer, or external hard drive, your Gateway creates a secure wireless network. In most cases, this only requires the pressing of a few buttons – one on your Gateway and one on the wireless client. This could be either a built‐in button or one on a compatible wireless adapter/card, or a virtual button in software. Once completed, this allows wireless clients to join your wireless network. To initialize the WPS process, you can either press and release the WPS button located on the front of your Gateway or use the GUI and press the on‐screen button. If you press the WPS button on your Gateway and change your mind, you can cancel the WPS process by pressing the button a second time. You can easily add wireless devices to your wireless network using the WPS option if your wireless device supports the WPS feature. To access WPS using the user interface: From the Main menu, select Wireless Settings, then select Wi‐Fi Protected Setup (WPS). Page 13 ...
Page 18 Enable the protected setup by moving the selector to On. Use one of the following methods: If your wireless client device has a WPS button, press the WPS button on your Gateway, then click the WPS button on your wireless client to start the WPS registration process. If your client device has a WPS PIN, locate the PIN printed on the client’s label or in the client documentation. Enter the PIN number in the Client WPS PIN field. The Client WPS PIN field is located in the section B PIN Enrollment on the user interface. Click Register. After initializing WPS on your Gateway, you have two minutes to press the WPS button on the client device before the WPS session times out. When the WPS button on your Gateway is pressed, the Wireless light on the front of your Gateway begins flashing white. The flashing continues until WPS pairing to the client device completes successfully. At this time, the Wireless light turns solid white. If WPS fails to establish a connection to a wireless client device within two minutes, the Wireless light on your Gateway flashes red for two minutes to indicate the WPS pairing process was unsuccessful. After flashing red, the light returns to solid white to indicate that Wi‐Fi is on. Page 14 ...
Page 19: Main Screen
Wireless using Manual Configuration Verify each device that you are connecting wirelessly (using Wi‐Fi) has a built‐in wireless or external wireless adapter. Open the device’s wireless settings application. Select your Gateway’s wireless network name (SSID) from the device’s list of discovered wireless networks. Enter your Gateway’s wireless password (WPA2 key) into the device’s wireless settings. Your Gateway’s default wireless network name and wireless password are located are on the sticker on the side of your Gateway. Verify the changes were implemented by using the device’s web browser to access a site on the Internet. Repeat these steps for every device that you are wirelessly connecting to your Gateway. Coaxial Verify all coax devices are turned off. Disconnect any adapter currently connected to the coaxial wall jack in the room where your Gateway is located. Connect one end of the coaxial cable to the coaxial wall jack and the other end to the Coax port on your network device. Power up the network device. Main Screen When you log into your Gateway, the page displays showing the Main navigation menu at the top of the page and your Gateway’s Status, including Quick Links, My Network, and Verizon Zone display in the body of the page. Page 15 ...
Page 20: Menu
Menu The Main menu contains links to the following configuration options and chapters: • Wireless Settings – Chapter 3 • My Network – Chapter 5 • Firewall Settings – Chapter 6 • Parental Controls – Chapter 7 • Advanced – Chapter 8 • System Monitoring – Chapter 9 Page 16 ...
Page 21: Status
Status This section displays the status of your Gateway’s local network (LAN) and Internet connection (WAN). Broadband Connection Broadband Connection displays the state of the broadband connection: • Broadband interface: Ethernet or Coax • Connected status: Connected or No Connection • Connection type: DHCP or Static • WAN IP address: Address of the broadband connection Quick Links Quick Links contain links to frequently accessed documentation, such as User Guide, Quick Setup Wizard, and Verizon Help, and links to settings, such as Change Wireless Settings, Change Admin Password, and Port Forwarding, as well as Logout to logout of your Gateway’s GUI. My Network My Network displays the connection type, IP address, and status of all devices that have accessed or are currently connected to the network. The icon associated with the device displays to signify the device is active or shaded gray to indicate the device has not been active for several minutes. You can view the individual settings of each device by clicking its icon. Verizon Zone The Verizon Zone contains links to various Verizon web sites and other informational links. Page 17 ...
Page 22: Chapter 3 Wireless Settings
Chapter 3 Wireless Settings Wireless networking enables you to free yourself from wires and plugs, making your devices more accessible and easier to use. You can create a wireless network, including accessing and configuring wireless security options. Overview Your Gateway provides you with wireless connectivity using the 802.11b, g, n, or ac standards. These are the most common wireless standards. 802.11b has a maximum data rate of 11 Mbps, 802.11g has a maximum data rate of 54 Mbps, 802.11n has a maximum data rate of 450 Mbps, and 802.11ac has a maximum data rate of 1300 Mbps. 802.11b and g standards operate in the 2.4 GHz range. 802.11n operates in both the 2.4 GHz and 5 GHz ranges. 802.11ac operates in the 5 GHz range. Note: 802.11 b is a legacy mode and is not recommended. Even one 802.11b device connected to the network will slow your entire wireless network. The wireless service and wireless security are activated by default. The level of security is preset to WPA2 encryption using a unique default WPA2 key (also referred to as a passphrase or password) pre‐configured at the factory. This information is displayed on a sticker located on the side of your Gateway. Your Gateway integrates multiple layers of security. These include Wired Equivalent Privacy (WEP), Wi‐Fi Protected Access (WPA and WPA2), and firewall. Page 18 ...
Page 23: Wireless Status
Wireless Status Use the Wireless Status feature to view the status of your Gateway’s wireless network. To view the status: Access the Main page. You can quickly view your Gateway’s wireless status in the My Network column. This includes all devices that have recently accessed or are currently connected to the network. Select the Wireless Settings icon. The Wireless Status page displays additional wireless details. Page 19 ...
Page 24 On the Wireless Status page for either 2.4 GHz or 5 GHz, the following information displays: Radio Enabled – displays whether the wireless radio is active. SSID – displays the SSID (Service Set Identifier) shared among all devices on a wireless network. The SSID is the network name. All devices must use the same SSID. Channel – displays the channel the wireless connection is currently using. Security Enabled – displays the type of security active on the wireless connection as well as the security encryption key. SSID Broadcast – displays whether your Gateway is broadcasting its SSID. If activated, the SSID of your Gateway wireless network is broadcast wirelessly. If not activated, the SSID is hidden and the wireless clients must be manually configured to use the SSID. MAC Authentication – displays whether your Gateway is using MAC (Media Access Control) address authentication to allow wireless devices to join the network. Wireless Mode – displays the types of wireless device that can join the network. Page 20 ...
Page 25: Basic Security Settings
WMM – displays whether WMM is enabled on your Gateway. Packets Received/Sent – displays the number of packets received and sent since the wireless capability was activated. Basic Security Settings You can configure the basic security settings for your Gateway’s wireless network. Note: Your Gateway’s recommended wireless security encryption is set to WPA2. This is the factory default. This section explains how to activate WEP (Wired Equivalent Privacy) wireless security. WEP is a significantly less robust security compared to WPA or WPA2 and is not recommended. To set up WPA2 wireless security, refer to the WPA2 section. To configure basic security to WEP: On the Wireless Settings page, select Basic Security Settings. Page 21 ...
Page 26 To activate the wireless radio, click the On radio button. If desired, enter a new name for the wireless network in the SSID field or leave the default name that displays automatically. Select the channel you want the wireless radio to use to communicate or accept the default channel, then select the Keep my channel selection during power cycle check box to save your channel selection when your Gateway is rebooted. To active WEP (Wired Equivalent Privacy) security, click the WEP radio button. Select a WEP security level as 64/40 bit or 128/104 bit. Enter the key code. If using a HEX key, each character must be a letter from A to F or a number from 0 to 9. If the key is ASCII, each character can be either any ASCII or alphanumeric character. If using 64/40 bit, enter 10 HEX or 5 ASCII/alphanumeric characters. If 128/104, enter 26 HEX or 5 ASCII/alphanumeric characters. Be sure to write down the wireless settings for future use. Other wireless devices that will be connected to your Gateway must be configured to use these settings to join your Gateway’s wireless network. Click Apply to save changes. Page 22 ...
Page 27: Advanced Security Settings
Advanced Security Settings You can change your advanced wireless security settings, such as configuring wireless encryption to prevent unauthorized access or damage to your network devices; disable your SSID broadcast to secure your wireless traffic; stop your Gateway from broadcasting your SSID; set Wireless MAC Authentication to limit access to specific wireless devices; and change the wireless mode to limit or allow access to your wireless network based on the type of technology as well as other advanced wireless options. To modify the security settings for either 2.4 GHz or 5 GHz: In the Wireless Settings page, select Advanced Security Settings. Page 23 ...
Page 28: Level 1: Securing Your Network
Level 1: Securing your Network In the Level 1 section, select the type of wireless security. Depending on your selection, one of the following pages displays. WEP If WEP was selected, the WEP Settings page displays. To set the WEP security: In the Network Authentication field, select the authentication level as Open System Authentication, Shared Key Authentication or Both. In the WEP Keys section, activate the encryption key be entering the key name in the Encryption Key column. If HEX, the key must be hexadecimal digits. If ASCII, any characters can be used. Specify the length of key 1 by selecting 64/40 bit or 128/104 bit in the Key Length field and HEX or ASCII in the Entry Method field. Click Apply to save changes. Page 24 ...
Page 29 WPA If WPA (Wi‐Fi Protected Access) was selected, the WPA Key page displays. You can review the User Guidance on Password Selection section. To set the WPA security: Enter the Pre‐Shared Key as a wireless password or WPA key. To activate the group key update interval, select the Group Key Update Interval check box and set the interval time in seconds. Click Apply to save the changes. WPA2 If WPA2 (Wi‐Fi Protected Access II) was selected, the WPA2 page displays. WPA2 is the default wireless security protocol. You can review the User Guidance on Password Selection section. To set the WPA2 security: Enter the Pre‐Shared Key. Page 25 ...
Page 30: Level 2: Ssid Broadcast
Select the encryption algorithm as TKIP and AES or AES. To activate the group key update interval, select the Group Key Update Interval check box and set the interval time in seconds. Click Apply to save the changes. Level 2: SSID Broadcast You can configure your Gateway’s SSID broadcast capabilities to allow or disallow wireless devices from automatically using a broadcast SSID name to detect your Gateway wireless network. To enable or disable SSID broadcast: In the Advanced Settings page, locate the Level 2 section. Click the 2.4 GHz SSID Broadcast or 5 GHz SSID Broadcast link for the wireless network you wish to modify. The following example uses the 2.4 GHz network. The display configuration looks basically the same for the 5 GHz network. Page 26 ...
Page 31: Level 3: Limit Access
To enable SSID broadcasting, click the Enable radio button. SSID broadcast is enabled by default. The SSID of the wireless network will be broadcast to all wireless devices. To disable SSID broadcasting, click the Disable radio button. The public SSID broadcast will be hidden from all wireless devices. You will need to manually configure additional wireless devices to join the wireless network. Click Apply to save the changes. Level 3: Limit Access You can configure your Gateway to limit access to your wireless network allowing access only to those devices with specific MAC addresses or based on the type of wireless technology used. To limit access: In the Advanced Settings page, locate the Level 3 section. Page 27 ...
Page 32 To allow only devices with specific MAC addresses, click the Wireless MAC Authentication link. The Wireless MAC Authentication page displays. For additional details, refer to the Wireless MAC Authentication section. To limit access based on the type of technology, click the 802.11 b/g/n/ac Mode link. The 802.11 b/g/n/ac Mode page displays. For additional details, refer to the 802.11 b/g/n/ac Mode section. To access other advanced wireless options, click the Other Advanced Wireless Options link. The Other Advanced Wireless Options page displays. For additional details, refer to the Other Advanced Wireless Options section. Page 28 ...
Page 33: Wireless Mac Authentication
Wireless MAC Authentication You can allow or deny access to your wireless network by specifying devices with specific MAC addresses. Page 29 ...
Page 34: 802.11 Mode
To set Wireless MAC Authentication: On the Advanced Settings page, locate the Level 3 section and click the Wireless MAC Authentication link. The Wireless MAC Authentication page displays. To enable access control, select the Enable Access List check box. Select either: Accept all devices listed below – allows only the listed devices to access the wireless network. WARNING: This will block wireless network access for all devices not in the list. Only devices in the list will be able to connect to the wireless network. Deny all devices listed below – denies access to the listed devices. All other wireless devices will be able to access the wireless network if they use the correct wireless password. Enter the MAC address of a device, then click Add. Repeat step 2 to add additional devices, as needed. To remove a specific device’s MAC address, click the Remove button next to the specific MAC address. When all changes are complete, click Apply to save changes. 802.11 Mode From the 802.11 Mode page, you can limit the wireless access to your network by selecting the 2.4 GHz and 5 GHz wireless communication standard (mode) best suited or compatible with the devices you allow access to your wireless network. Page 30 ...
Page 35: Other Advanced Wireless Options
To select the 802.11 Mode: On the Advanced Settings page, locate the Level 3 section and click the 802.11 Mode link. The 802.11 Mode page displays. Select the 2.4 GHz Wireless Mode as follows: Compatibility – This is the default mode setting, providing a good balance of performance and compatibility with existing wireless devices. 802.11b, g, and n devices can connect. Legacy – For older wireless devices. Only 802.11b and g devices can connect. 802.11b (legacy mode) will cause your wireless network to slow and is not recommended. Performance – For newer wireless 802.11n devices only. No other devices can be used. Select the 5 GHz Wireless Mode as follows: N and AC Mode – This is the default setting. Both 802.11n and 802.11ac are available on the 5 GHz frequencies. N Only Mode – The 5 GHz frequencies are available to 802.11n devices. 802.11ac is not enabled. AC Only Mode – This provides maximum performance. 802.11ac devices will have exclusive use of the 5 GHz frequencies and 802.11n devices will not be able to connect at 5 GHz. Click Apply to save the changes. Other Advanced Wireless Options You can view additional wireless options. To view the options: In the Advanced Settings page, locate the Level 3 section and click Other Advanced Wireless Options link. A warning message displays. Click OK. The Other Advanced Wireless Options page displays. Page 31 ...
Page 36 Page 32 ...
Page 37 View the following options: Caution! These settings should only be configured by experienced network technicians. Changing the settings could adversely affect the operation of your Gateway and your local network. Transmission Rate – displays status as Auto Transmit Power – adjusts the power of the wireless signal CTS (Clear to Send) Protection Mode – allows mixed 802.11b/g/n/ac networks to operate at maximum efficiency CTS Protection Type – displays cts, which is only for mixed 802.11b/g/n/ac networks or rts‐cts, which is for 802.11a/b/g networks Frame Burst – Max Number – allows packet bursting, which increases overall network speed Frame Burst – Burst Time – indicates the burst time of the frame bursts Beacon Interval – displays the time period of the beacon interval DTIM (Delivery Traffic Indication Message) Interval – provides a countdown mechanism, informing wireless network clients of the next window for listening to broadcast and multicast messages Fragmentation Threshold – increases the reliability of frame transmissions on the wireless network RTS Threshold – controls the size of the data packet that the low level RF protocol issues to an RTS packet MSDU Aggregation – enables or disables MSDU aggregation MPDU Aggregation – enables or disables MPDU aggregation To access the WMM settings, click the WMM Settings link. Click Apply to save changes. Page 33 ...
Page 38: Wmm Settings
WMM Settings You can prioritize the types of data transmitted over the wireless network using the advanced WMM settings. Wireless QoS (WMM) can improve the quality of service (QoS) for voice, video, and audio streaming over Wi‐Fi by prioritizing these data streams. WMM Power Save can improve battery life on mobile Wi‐Fi devices such as smart phones and tablets by fine‐tuning power consumption. WMM (Wi‐Fi Multimedia) QoS and Power Save require a wireless client device which also supports WMM. To set the options: In the Advanced Wireless Options page, click WMM Settings link. A warning message displays. Click Yes. The WMM Settings page displays. To enable Wireless QoS (WMM), select the Enabled check box. To enable WMM Power Save, enable Wireless QoS (WMM) first, then enable WMM Power Save by selecting the Enabled check box. Click Apply to save changes. Page 34 ...
Page 39: Chapter 4 Configuring My Network Settings
Chapter 4 Configuring My Network Settings You can configure the basic network settings for your Gateway’s network. Caution! The settings described in this chapter should only be configured by experienced network technicians. Changes could adversely affect the operation of your Gateway and your local network. Accessing My Network Settings My Network allows you to view and manage your network connections and devices. You can block websites and Internet services, set port forwarding, view device details, and rename devices. To view your network connections: On the Main page, select the My Network icon. The My Network page opens with our current status displayed. Page 35 ...
Page 40: Using My Network Settings
Using My Network Settings You can access and configure common network parameters: • Website Blocking To block specific websites, click Website Blocking. The Parental Control page displays. For additional information about blocking websites, refer to Chapter 7 Using Parental Controls. • Block Internet Services Internet services blocking prevents a device on your network from accessing specific services, such as receiving email or downloading files from FTP sites. Block Internet services by locating the device, then clicking Block Internet Services. The Access Control page displays. For additional information on blocking Internet services, refer to the Access Control section in Chapter 6 Configuring System Settings. • Port Forwarding Port Forwarding allows your network to be exposed to the Internet in specific limited and controlled ways. For example, you could allow specific applications, such as gaming, voice, and chat, to access servers in the local network. To access the Port Forwarding page, click Port Forwarding. For additional information, refer to the Port Forwarding section in Chapter 6 Configuring System Settings. • View Device Details Click View Device Details to display the Device Information page and view the selected device’s information, such as IP Address, MAC address, Network Connection, Lease Type, Port Forwarding Services, and Windows Shared Folder as well as the Ping Test option. You can also click the device’s icon in the Main page to display the Device Information page. • Rename this Device To change the name of a specific device, click Rename this Device. The Rename Device page displays. If desired, enter the new device name and/or select a different icon. Click Apply to save changes. The My Network page will open with the new name and icon displayed. Page 36 ...
Page 41: Chapter 5 Using Network Connections
Chapter 5 Using Network Connections Your Gateway supports various local area network (LAN) and wide area network (WAN), or Internet connections using Ethernet or coaxial cables. You can configure aspects of the network and Internet connections as well as create new connections. Caution! The settings described in this chapter should only be configured by experienced network technicians. Changes could adversely affect the operation of your Gateway and your local network. Accessing Network Connections You can access your network connections and view the connections by connection type. To access the network connections: Select My Network, then select Network Connections. Page 37 ...
Page 42: Network (Home/Office) Connection
To display all connection entries, click the Advanced button. To select a specific network connection, click the hyperlinked name. The following sections detail the types of network connections that you can view. Network (Home/Office) Connection You can view the properties of your local network. This connection is used to combine several network devices under one virtual network. For example, you can create a home/office network connection for Ethernet and other network devices. Note: When a network connection is disabled, the formerly underlying devices connected to it will not be able to obtain a new DHCP address from that Gateway network interface. To view the connection: On the Network Connections page, click the Network (Home/Office) connection link. The Network (Home/Office) Properties page displays. Page 38 ...
Page 43 To disable an active network connection, click Disable. To rename a network connection, enter the new network name in the Name field. Click Apply to save the changes. Configuring the Home/Office Network To configure a network connection: In the Network (Home/Office) Properties page, click Settings. The configuration page displays. Page 39 ...
Page 44 Configure the following sections, as needed. General In the General section, verify the following information: Status – displays the connection status of the network Network – displays the type of network connection Connection Type – displays the type of connection Physical Address – displays the physical address of the network card used for the network MTU – specifies the Maximum Transmission Unit (MTU) specifies the largest packet size permitted for Internet transmissions: ⎯ Automatic – sets the MTU at 1500 ⎯ Automatic by DHCP – sets the MTU according to the DHCP connection ⎯ Manual – allows you to manually set the MTU Page 40 ...
Page 45 Internet Protocol In the Internet Protocol section, specify one of the following: Obtain an IP Address Automatically – the network connection is required by Verizon to obtain an IP address automatically (default). The DHCP server assigning the IP address also assigns a subnet mask address. The subnet mask address can be overridden by entering a different subnet mask address provided by Verizon or experienced network technician. Use the Following IP Address – the network connection uses a permanent or static IP address and subnet mask address, provided by Verizon or experienced network technician. Use the Following IP Address ‐ the network connection uses a permanent or static IP address, then the IP address and subnet mask address. Bridge In the Bridge section of the Configure Network (Home/Office), you can configure the various LAN interfaces. By default, the Ethernet, Coax, and Wireless Access Point connections are activated. Caution! Do not change these settings unless specifically instructed to by Verizon. Changes could adversely affect the operation of your Gateway and your local network. Page 41 ...
Page 46 Verify the following information: Status – displays the connection status of a specific device. STP – enables Spanning Tree Protocol on the device. This protocol provides a path redundancy while preventing undesirable communication loops in the network. Action – contains an icon that, when clicked, generates the next lower‐level configuration page for the specific network connection or network device. For example, when you click the Action icon, you can configure the DNS server in the lower‐level network connection properties settings for the Broadband Connection (Ethernet/Coax) network. Page 42 ...
Page 47 In addition, the DHCP and Routing actions listed below are examples of the actions that can be configured for the Broadband Connection (Ethernet/Coax) and Network (Home/Office) networks. DNS Server The DNS (Domain Name System) is the naming system method by which websites or domain names are translated into IP addresses. To configure your Gateway’s Broadband Connection (Ethernet/Coax) network to use a specific DNS server, refer to the DNS Server section of the Properties page. To manually configure a DNS server using the DNS addresses provided by Verizon: Specify the following DNS Server addresses: the Primary and Secondary DNS server addresses. Click Apply to save the changes. DHCP Server The IP Address Distribution section of the Properties settings is used to configure your Gateway’s Dynamic Host Configuration Protocol (DHCP) server parameters. Once enabled and configure, the DHCP server automatically assigns IP addresses to any network devices which are set to obtain their IP address dynamically. If DHCP Server is enabled on your Gateway, configure the network devices as DHCP Clients. There are 2 basic options in this section: Disabled and DHCP Server. To set up the Gateway’s network bridge to function as a DHCP server: In the IP Address Distribution section, select the DHCP server. Once enabled, the DHCP server provides automatic IP assignments (also referred to as IP leases) based on the preset IP range defined below. Start IP Address – Enter the first IP address in the IP range that the Gateway will automatically begin assigning IP addresses from. Since your Gateway’s IP address is 192.168.1.1, the default Start IP Address is 192.168.1.2. End IP Address – Enter the last IP address in the IP range that the Gateway will automatically stop the IP address allocation at. The maximum end IP address range that can be entered is 192.168.1.254. If Windows Internet Naming Service (WINS) is being used, enter the WINS server address. In the Lease Time in Minutes field, enter the amount of time a network device is allowed to connect to the Gateway with its currently issued dynamic IP address. To have the Gateway automatically assign a host name to network devices, select the Provide Host Name if Not Specified by Client check box. Click Apply to save changes. Page 43 ...
Page 48 Routing You can configure your Gateway to use static or dynamic routing. • Static routing – specifies a fixed routing path to neighboring destinations based on predetermined metrics. • Dynamic routing – automatically adjusts how packets travel on the network. The path determination is based on network/device reachability and status of network being traveled. To configure routing: In the Device Metric field, enter a device metric. The device metric is a value used by your Gateway to determine whether one route is superior to another, based on parameters, such as bandwidth and delay time. In the Routing Table section, click Add New Route to display and modify the new route configuration page. Complete Network Connection Configuration Updates • To save your changes, click Apply. Page 44 ...
Page 49: Ethernet/Coax Connection
Ethernet/Coax Connection An Ethernet connection connects computers to your Gateway using Ethernet cables. The connections are either direct or use network hubs and switches. A Coax connection connects devices, such as set‐top boxes, to your Gateway using a coaxial cable. Note: If disabling the connection, you must reboot your Gateway for the change to take effect. To view the connection: In the Network Connections page, click the Broadband Connection (Ethernet/Coax) link. Page 45 ...
Page 50 To rename the network connection, enter the new name in the Name field. Click Apply to save changes. Configuring the Ethernet/Coax Connection To configure the connection: In the Broadband Connection (Ethernet/Coax) Properties page, click Settings. The configuration page displays. Page 46 ...
Page 51 Configure the following settings, as needed. General Verify the following information: Status – displays the connection status of the network Network – displays the type of network connection Connection Type – displays the type of connection Physical Address – displays the physical address of the network card used for the network MTU – specifies the largest packet size permitted for Internet transmissions: ⎯ Automatic – set the MTU (Maximum Transmission Unit) at 1500 ⎯ Automatic by DHCP – sets the MTU according to the DHCP connection ⎯ Manual – allows you to manually set the MTU Coax Link To set the Channel, select the coax link channel as 1 to 3. Page 47 ...
Page 52: Wireless Access Point Connection
Select the On or Off radio button in the Auto Detection field. To set privacy, select the Enabled check box. This causes all devices connected to the coaxial cable to use the same password. This is recommended. To set the password, enter the Coax Link password in the Password field. To set the CM ratio, select the CM ratio in drop down. To enable or disable the Coax link, click Disable or Enable. To view the devices connected using the coaxial cable, click the Go to WAN Coax Stats link. HW Switch Ports To generate the Port Settings page and set the HW Switch Ports: In the HW Switch Ports section, verify the connection status of the 4 Ethernet ports and 1 coax port. To edit network traffic policies, click the Action icon. Complete all Ethernet/Coax Connection Configuration Updates To save your changes: Click Apply. Wireless Access Point Connection A Wireless Access Point network connection allows wireless devices to connect to the local area network (LAN) using the 2.4 GHz or 5 GHz Wi‐Fi network. Note: Once disabled, all wireless devices connected to that wireless network will be disconnected from the LAN network and Internet. To view the connection: In the Network Connections page, click Advanced. Page 48 ...
Page 53 Click 5 GHz Wireless Access Point 1 or 2.4 GHz Wireless Access Point 2. Page 49 ...
Page 54 To disable the connection, click Disable. To rename the connection, enter a name in the Name field. Click Apply to save the changes. Reboot your Gateway. Configuring the Wireless Access Point Properties To configure the connection: In the Wireless Access Point Properties page, click Settings. The configuration page displays. Page 50 ...
Page 55: Broadband Ethernet/Coax Connection
Verify the following information: Status – displays the connection status of the network Network – displays the type of network connection Connection Type – displays the type of connection Physical Address – displays the physical address of the network card used for the network MTU – specifies the largest packet size permitted for Internet transmissions: ⎯ Automatic – set the MTU (Maximum Transmission Unit) at 1500 ⎯ Automatic by DHCP – sets the MTU according to the DHCP connection ⎯ Manual – allows you to manually set the MTU Click Apply to save changes. Broadband Ethernet/Coax Connection A Broadband Ethernet connection connects computers to your Gateway using Ethernet cables. The connections are either direct or use network hubs and switches. A Coax connection connects devices, such as set‐top boxes, to your Gateway using a coaxial cable. Note: If disabling the connection, you must reboot your Gateway for the change to take effect. To view the connection: In the Network Connections page, click the Broadband Connection (Ethernet/Coax) link. Page 51 ...
Page 56 To rename the network connection, enter the new name in the Name field. Click Apply to save changes. Page 52 ...
Page 57 Configuring the Ethernet/Coax Connection To configure the connection: In the Broadband Connection (Ethernet/Coax) Properties page, click Settings. The configuration page displays. Configure the following settings, as needed. General Verify the following information: Status – displays the connection status of the network Network – displays the type of network connection Connection Type – displays the type of connection Physical Address – displays the physical address of the network card used for the network MTU – specifies the largest packet size permitted for Internet transmissions: ⎯ Automatic – set the MTU (Maximum Transmission Unit) at 1500 ⎯ Automatic by DHCP – sets the MTU according to the DHCP connection ⎯ Manual – allows you to manually set the MTU Page 53 ...
Page 58 Coax Link To set the Channel, select the coax link channel as 1 to 3. Select the On or Off radio button in the Auto Detection field. To set privacy, select the Enabled check box. This causes all devices connected to the coaxial cable to use the same password. This is recommended. To set the password, enter the Coax Link password in the Password field. To set the CM ratio, select the CM ratio in drop down. To enable or disable the Coax link, click Disable or Enable. To view the devices connected using the coaxial cable, click the Go to WAN Coax Stats link. Internet Protocol In the Internet Protocol section, specify one of the following: No IP Address – the connection has no IP address. This is useful if the connection operates under a bridge. Obtain an IP Address Automatically – the network connection is required by Verizon to obtain an IP address automatically. The server assigning the IP address also assigns a subnet mask address, which can be overridden by entering another subnet mask address. Page 54 ...
Page 59 Use the Following IP Address ‐ the network connection uses a permanent or static IP address, then the IP address and subnet mask address. To override the subnet mask, select the Override Subnet Mask check box, then enter the new subnet mask. Routing Mode Page 55 ...
Page 60 Complete all Ethernet/Coax Connection Configuration Updates To save your changes: Click Apply. Page 56 ...
Page 61: Chapter 6 Configuring Security Settings
Chapter 6 Configuring Security Settings Your Gateway’s security suite includes comprehensive and robust security services, such as stateful packet inspection, firewall security, user authentication protocols, and password protection mechanisms. These features help protect your computers from security threats on the Internet. This chapter covers the following security features: • Firewall – select the security level for the firewall • Access Control – restrict access from the local network to the Internet • Port Forwarding – enable access from the Internet to specific services provided by computers on the local network • Port Triggering – define port triggering entries to dynamically open the firewall for specific protocols or ports • Remote Administration – enable remote configuration of your Gateway from any Internet‐accessible computer • Static NAT – allow multiple static NAT IP addresses to be designated to devices on the network • Security Log – view and configure the security log Firewall The firewall is the cornerstone of the security suite for your Gateway. It has been exclusively tailored to the needs of the residential or office user and is pre‐configured to provide optimum security. The firewall provides both the security and flexibility home and office users seek. It provides a managed, professional level of network security while enabling the safe use of interactive applications, such as Internet gaming and video conferencing. Additional features, including surfing restrictions and access control, can also be configured locally through the user interface or remotely by a service provider. The firewall regulates the flow of data between the local network and the Internet. Both incoming and outgoing data are inspected, then either accepted and allowed to pass through your Gateway or rejected and barred from passing through your Gateway, according to a flexible and configurable set of rules. These rules are designed to prevent unwanted intrusions from the outside, while allowing local network users access to Internet services. ...
Page 62: Setting Firewall Configuration
The firewall rules specify the type of services on the Internet that are accessible from the local network and types of services in the local network that are accessible from the Internet. Each request for a service that the firewall receives is checked against the firewall rules to determine whether the request should be allowed to pass through the firewall. If the request is permitted to pass, all subsequent data associated with this request or session is also allowed to pass, regardless of its direction. For example, when accessing a website on the Internet, a request is sent to the Internet for this site. When the request reaches your Gateway, the firewall identifies the request type and origin, such as HTTP and a specific computer in the local network. Unless your Gateway is configured to block requests of this type from this computer, the firewall allows this type of request to pass to the Internet. When the website is returned from the web server, the firewall associates the website with this session and allows it to pass; regardless HTTP access from the Internet to the local network is blocked or permitted. It is the origin of the request, not subsequent responses to this request, which determines whether a session can be established. Setting Firewall Configuration You can select a maximum, typical, or minimum security level to block, limit, or permit all traffic. The following table shows request access for each security level. Security Level Internet Requests Local Network Requests Incoming Traffic Outgoing Traffic Maximum Blocked Limited Typical Blocked Unrestricted Minimum Unrestricted Unrestricted The request access is defined as: • Blocked traffic – no access allowed, except as configured in Port Forwarding and Remote Access •...
Page 63: Specifying General Settings For Ipv4 Or Ipv6
Specifying General Settings for IPv4 or IPv6 To set your firewall configuration: Click the Firewall Settings icon. The General Settings page displays. Select a security level by clicking one of the radio buttons. Using the Minimum Security setting may expose the local network to significant security risks, and should only be used for short periods of time to allow temporary network access. To protect the local network from a common type of hacker attack that uses fragmented data packets to sabotage the network, select the Block IP Fragments check box. VPN over IPSec and some UDP‐based services make legitimate use of IP fragments. IP fragments must be allowed to pass into the local network to use these services. Click Apply to save changes. Page 59 ...
Page 64: Access Control
Access Control You can block individual computers on your local network from accessing specific services on the Internet. For example, you could block one computer from accessing the Internet, then block a second computer from transferring files using FTP as well as prohibit the computer from receiving incoming email. Access control incorporates a list of preset services, such as applications and common port settings. Allow or Restrict Services To allow or restrict services: From the Firewall page, select Access Control. The Access Control page opens with the Allows and Blocked sections displayed. The Allowed section only displays when the firewall is set to maximum security. To block a service, click Add. The Add Access Control Rule page displays. Page 60 ...
Page 65: Disable Access Control
To apply the rule to: All networked devices – select Any. Specific devices only – select User Defined, then click Add and create a network object. In the Protocol field, select the Internet protocol to be allowed or blocked. If the service is not included in the list, select User Defined. The Edit Service page displays. Define the service, then click OK. The service is automatically added to the Add Access Control Rule section. Specify when the rule is active as Always or User Defined and click Add to create the schedule. Click Apply to save changes. The Access Control page displays a summary of the new access control rule. Disable Access Control You can disable an access control and enable access to the service without removing the service from the Access Control table. This can make the service available temporarily and allow you to easily reinstate the restriction later. • To disable an access control, clear the check box next to the service name. • To reinstate the restriction, select the check box next to the service name. • To remove an access restriction, select the service and click Remove. The service is removed from the Access Control table. Page 61 ...
Page 66: Port Forwarding
Port Forwarding You can activate port forwarding to expose the network to the Internet in a limited and controlled manner. For example, enabling applications, such as gaming and voice, to work from the local network as well as allowing Internet access to servers within the local network. To create port forwarding rules: From the Firewall page, select Port Forwarding. The Port Forwarding page opens with the current rules displayed. To create a new rule, select the IP address in the Select IP from Menu drop down. Select the application in the Application to Forward drop down. Click Add. The rule displays in the Applied Rules section. Click Apply to save changes. Advanced Port Forwarding Rules You can configure advanced port forwarding rules. To configure the rules: In the Port Forwarding page, select Advanced. Page 62 ...
Page 67 If needed, to select a port to forward communication to, select an option in the Forward to Port list box. If a single port or range of ports is selected, a text box displays. Enter the port numbers. To schedule the rule, select either Always or User Defined in the Schedule list box. Click Add. The rule displays in the Applied Rules section. Click Apply to save changes. Page 63 ...
Page 68: Port Triggering
Port Triggering Port triggering can be described as dynamic port forwarding. By setting port triggering rules, inbound traffic arrives at a specific network host using ports that are different than those used for outbound traffic. The outbound traffic triggers the ports where the inbound traffic is directed. For example, a gaming server is accessed using UDP protocol on port 2222. The gaming server then responds by connecting the user using UDP on port 3333, when a gaming session is initiated. In this case, port triggering must be used since it conflicts with the following default firewall settings: • Firewall blocks inbound traffic by default. • Server replies to your Gateway IP, and the connection is not sent back to the host since it is not part of a session. To resolve the conflict, a port triggering entry must be defined, which allows inbound traffic on UDP port 3333 only after a network host generated traffic to UDP port 2222. This results in your Gateway accepting the inbound traffic from the gaming server and sending it back to the network host which originated the outgoing traffic to UDP port 2222. To configure port triggering: Select Port Triggering. Page 64 ...
Page 69: Remote Administration
To add a service as an active protocol, click Add. The Edit Port Triggering Rule page displays. Enter the service name then configure its inbound and outbound trigger ports. Click Apply to save User Defined changes. The Port Triggering page displays. Click Apply again to save all changes. Remote Administration Caution! Enabling Remote Administration places your Gateway network at risk from outside attacks. You can access and control your Gateway not only from within the local network, but also from the Internet using Remote Administration. You can allow incoming access to the following: • SSH Access – used to create a command‐line session and gain access to all system settings and parameters using a text‐based terminal. • Web Management – used to obtain access to your Gateway’s GUI and gain access to all settings and parameters through a web browser. Both secure HTTPS and non‐ secure HTTP access is available. • Diagnostic Tools – used for troubleshooting and remote system management by a user or Verizon. Page 65 ...
Page 70 SSH and Web Management remote administration access may be used to modify or disable firewall settings. Local IP addresses and other settings can also be changed, making it difficult or impossible to access your Gateway from the local network. Remote administration access to SSH or Web Management services should be activated only when absolutely necessary. Note: Encrypted remote administration is performed using a secure SSL connection and requires a SSL certificate. When accessing your Gateway for the first time using encrypted remote administration, a warning page opens with a certificate authentication message displayed. This is due to your Gateway SSL certificate being self‐generated. When this message display under that circumstance, ignore the message and continue. Even though this message displays, the self‐generated certificate is safe and provides a secure SSL connection. To enable remote administration: Select Remote Administration. Page 66 ...
Page 71: Static Nat
To enable access, select the check box. Click Apply to save changes. To remove access, clear the check box. Click Apply again to save changes. Static NAT Static NAT allows devices located behind a firewall that is configured with private IP addresses to appear to have public IP addresses to the Internet. This allows an internal host, such as a web server, to have an unregistered (private) IP address and still be accessible over the Internet. To configure static NAT: Select Static NAT. To create a static NAT, click Add. The Add NAT/NAPT Rule page displays. Page 67 ...
Page 72: Security Log
Select a source address in the Specify Address field or enter an IP address in the text box. Enter the public IP address. If using port forwarding, select the Enable Port Forwarding for Static NAT check box. Click Apply to save changes. Repeat these steps to add additional static IP addresses. Security Log You can view events that your firewall has blocked by accessing the security log. Your Gateway reports events, such as attempts to establish inbound and outbound connections, attempts to authenticate at an administrative interface, such as your Gateway GUI, firewall configuration, and system start‐up. The security log reports the following information: • Time – based on the date and time in your Gateway • Event – consists of firewall information, firewall setup, and system log • Event Type – describes the event that occurred, such as a fragmented packet or parental controls. • Details – provide a reason the event occurred, such as a packet has been blocked because of parental control. You can modify the type of events that display in the security log. This does not modify the event itself. It simply changes the information that displays in the log. Page 68 ...
Page 73: Event Types
Event Types The security logs records the following event types: • Access control – a packet has been accepted/blocked due to an access control rule. • Advance filter rule – a packet has been accepted/blocked due to an advanced filter rule. • ARP – an ARP packet has been accepted. • AUTH:113 request ‐ an outbound packet for AUTH protocol has been accepted (for maximum security level). • Broadcast/Multicast protection – a packet with a broadcast/multicast source IP has been blocked. • Default policy – a packet has been accepted/blocked according to the default policy. • Defragmentation failed – the fragment has been stored in memory and blocked until all fragments have arrived and defragmentation can be performed. • DHCP request – your Gateway sent a DHCP request (depends on the distribution). • DHCP response ‐ your Gateway sent a DHCP response (depends on the distribution). • Echo/Chargen/Quote/Snork protection – a packet has been blocked due to Echo/Chargen/Quote/Snork protection. • Firewall internal – from the firewall internal mechanism, event type is recorded and an accompanying explanation will be added. • Firewall rules were changed – the rule set has been modified. • Firewall status changed – the firewall status changed from up to down or vice versa, as specified in the event type description. • First packet in connection is not a SYN packet – a packet has been blocked due to a TCP connection that started without a SYN packet. • Fragmented packet – a fragment has been rejected. ...
Page 74 • Fragmented packet, packet exceeds – a packet has been blocked because, after defragmentation, the packet exceeded. • Fragmented packet, packet too big – a packet has been blocked because, after defragmentation, the packet was too big. • FTP port request to 3 party is forbidden – possible bounce attack – a packet has been blocked. • ICMP flood protection – a broadcast ICMP (Internet Control Message Protocol) flood. • ICMP protection – a broadcast ICMP message has been blocked. • ICMP redirect protection – an ICMP redirected message has been blocked. • ICMP replay – an ICMP replay message has been blocked. • Illegal packet options – the options field in the packet’s header is either illegal or forbidden. • IP Version 6 – an IPv6 packet has been accepted. • Malformed packet: Failed parsing – a packed has been blocked because it is malformed. • Maximum security enabled service – a packet has been accepted because it belongs to a permitted service in the maximum security level. • Multicast IGMP connection – a multicast packet has been accepted. • NAT Error: Connection pool is full ‐ No connection created – a connection has not been created because the connection pool is full. • NAT Error: Conflict mapping already exists – a conflict occurred because the NAT mapping already exists, so NAT failed. • NAT Error: No free NAT IP – no free NAT IP, so NAT has failed. •...
Page 75 • Trusted device – a packet from a trusted device has been accepted. • UDP flood protection – a packed has been blocked, stopping a UDP flood. • User authentication – a message arrived during login time, including both successful and failed authentication. • Wildcard connection hooked – debug message regarding connection. • Wildcard connection opened ‐ debug message regarding connection. • WinNuke protection – a WinNuke attack has been blocked. To view the security log: Select Security Log. Page 71 ...
Page 76 To modify the types of events that display in the log, click Settings. Page 72 ...
Page 77 In the Accepted Events section, select the type of activities that generates a log message: Accepted Incoming Connections – generates a log message for each successful attempt to establish an inbound connection to the local network. Accepted Outgoing Connections ‐ generates a log message for each successful attempt to establish an outbound connection to the public network. In the Blocked Events section, select the type of blocked events you want logged. To log a message for each remote administration connection attempt, click the Remote Administration Attempts check box. To log the connection for handling by the firewall and application level Gateways, click the Connection States check box. Click Apply to save changes. The Security Log page displays. Page 73 ...
Page 78: Chapter 7 Setting Parental Controls
Chapter 7 Setting Parental Controls The abundance of harmful information on the Internet poses a serious challenge for employers and parents alike as they ask “How can I regulate what my employee or child does on the Internet?” With that question in mind, your Gateway’s Parental Controls were designed to allow control of Internet access on all locally networked devices. Activating Parental Controls You can create a basic access policy for any computer or device on your Gateway network. Parental controls limit Internet access to specific websites based on a schedule that you create. Access can be limited on specific websites or keywords embedded in a website. For example, you can block access to the ‘www.anysite.com’ as well as block any website that has the word ‘any’ in its site name. To limit computer access: Select Parental Control. Page 74 ...
Page 79 In Step 1, select the computers or device where you are limiting access in the Networked Computer/Device list box, then click Add. The devices display in the Selected Devices section. To remove a device from the Selected Devices list box, select the device, then click Remove. The device displays in the Networked Computer/Device list box. In Step 2, click one of the following options in the Limit Access By section: Block the following Websites and Embedded Keywords within a Website – blocks the specified websites and websites with names contained the specified keyword. Allow the following Websites and Embedded Keywords within a Website – allows the specified websites and websites with names contained the specified keyword. Block ALL Internet Access – will not allow the device to access the Internet. Enter the name of the website or keyword, then click Add. Page 75 ...
Page 80 To remove a website or keyword, select the word, then click Remove. Create a schedule by selecting the days of the week when the rule will be active or inactive. Page 76 ...
Page 81: Rule Summary
Set the time when the rule will be active or inactive, then specify the start time and end time. Create a rule name and description. Click Apply to save changes. Rule Summary You can view the rules created for your Gateway. • To view the rule summary, select Rule Summary. The Rule Summary page opens with the rule name, description, and computer or device displayed. You can view, edit, or delete the rule. Page 77 ...
Page 82: Chapter 8 Configuring Advanced Settings
Chapter 8 Configuring Advanced Settings Advanced settings cover a wide range of sophisticated configurations for your Gateway’s firmware and network. Caution! The settings described in this section should only be configured by experienced network technicians. Changes could adversely affect the operation of your Gateway and local network. Using Advanced Settings You can access the following settings: To access the advanced settings: Select Advanced. A warning page displays, asking if you want to proceed. Click Yes. The Advanced page displays. Page 78 ...
Page 83: Utilities
Select a topic by clicking the topic name. Utilities You can access the following advanced settings: • Diagnostics – performs diagnostic tests • Restore Defaults – resets your Gateway to it default settings • Reboot Router – restarts your Gateway • MAC Cloning – clones the MAC address • ARP Table – displays active devices with their IP and MAC addresses • Users – creates and manages remote users • Quality of Service (QoS) – contact Technical Support for detailed information • Local Administration – allows you to grant local SSH access • Remove Administration – detailed in Chapter 6 Configuring Your Network Settings Page 79 ...
Page 84: Diagnostics
Diagnostics You can use diagnostics to test network connectivity. To diagnose network connectivity: Select Diagnostics in the Advanced page. To ping an IP address, enter the IP address or domain name in the Destination field and click Go. The diagnostics will display the number of pings, status, packets sent, and round trip time. If no diagnostic status displays, click Refresh in your web browser. Click Close to exit the session. Restore Defaults You can restore your configuration settings to your Gateway factory default settings. Restoring the default settings erases the current configuration, including user defined settings and network connections. All connected DHCP client must request new IP addresses. Your Gateway must restart. Prior to restoring the factory defaults, you may want to save your current configuration to a file. This allows you to reapply your current settings and parameters to the default settings, as needed. For additional information, refer to the Configuration File section. Page 80 ...
Page 85: Reboot Gateway
Note: When restoring defaults, the setting and parameters of your Gateway are restored to their default values. This includes the Administrator password. A user‐specified password will no longer be valid. To restore your Gateway’s factory default settings: Select Restore Defaults in the Advanced page. To save your current configuration file, click Save Configuration File. To restore the factory default settings, click OK. The factory default settings are applied and your Gateway restarts. Once complete, the Login page for the First Time Easy Setup Wizard displays. Reboot Gateway You can reboot your Gateway using the Reboot Router feature as well as pressing and holding the WPS button on the front of the Gateway for at least 10 seconds. To reboot your Gateway: Select Reboot Router in the Advanced page. Page 81 ...
Page 86: Mac Cloning
To reboot, click OK. Your Gateway reboots. This may take up to a minute. To access your Gateway user interface, refresh your web browser. MAC Cloning A MAC address is a hexadecimal code that identifies a device on a network. All networkable devices have a unique MAC address. When replacing a network device on your Gateway, you can simplify the installation process by copying the MAC address of the existing device to your Gateway. To copy the MAC address of the existing device: Select MAC Cloning in the Advanced page. In the To Physical Address field, enter the MAC address of your new device. To locate the MAC address, refer to the documentation from the device manufacturer. Click Apply to save changes. Page 82 ...
Page 87: Arp Table
ARP Table You can view the IP and MAC addresses of each DHCP connection. To view the addresses: Select ARP Table in the Advanced page. Review the IP and MAC address for each device. When complete, click Close. Users You can view the users that can currently access your wireless network. In addition, you can modify their login password and name as well as manage the number of unsuccessful login attempts a user can enter before your Gateway temporarily denies all further login attempts by that user. To view users: Select Users in the Advanced page. Page 83 ...
Page 88 In the Login Configuration section, enter the maximum number of unsuccessful login attempts. To edit usernames and passwords, click the Edit icon in the Action column. The User Settings page displays. Page 84 ...
Page 89: Local Administration
To edit the username and set a new password, as needed. To add a new user, specify the following parameters: Full Name – name of the user. User Name – name the user enters to remotely access the home or office network. This field is case‐sensitive. To set a new Password, select the Set a new password check box. The New Password fields display. Verify the level of access for the user in the Permissions field. Click Apply to save changes. The Users page opens with the user information displayed. Click Apply again to save changes and exit. Local Administration You can grant local access on a specific port. To grant access: Select Local Administration in the Advanced page. To grant access, select the check box for the specific SSH access. Click Apply to save changes. Local access is granted. To remove access, clear the checkbox, then click Apply. No local access is granted. Page 85 ...
Page 90: Remote Administration
Remote Administration The Remote Administration parameters are detailed in Chapter 4 Configuring Your Network Settings. DNS Settings You can view and manage the DNS server host name and IP address as well as add a new computer. The DNS server does not require configuration. DNS Server You can edit the host name and/or IP address, if the host was manually added to the DNS table. If not, you can only modify the host name. To access the DNS server: Select DNS Server in the Advanced page. To view and add computers stored in the DNS table, click Add DNS Entry. The Add DNS Entry page displays. In the Host Name field, enter the name of the computer, then enter the IP address and click Apply to save changes. The DNS Server page displays. To edit the host name or IP address, click the Edit icon in the Action column. The DNS Entry page displays. Edit the host name and/or IP address, then click Apply to save changes. To remove a host from the DNS table, click the Delete icon in the Action column. Page 86 ...
Page 91: Network Settings
Network Settings You can configure the following network settings: • Network Objects – define a group, such as a group of computers • UPnP – checks the validity of all UPnP services and rules • IGMP Proxy – enables IGMP proxy • Port Forwarding Rules – displays port forwarding rules Network Objects Network objects define a group, such as a group of computers, on your Gateway network by MAC address, IP address, and /or host name. The defined group becomes a network object. You can apply settings, such as configuring system rules, to all devices defined in the network object. For example, instead of setting the same website filtering configuration individually to five computers one at a time, you can define the computers as a network object. Website filtering can then be simultaneously applied to all the computers. You can use network objects to apply security rules based on host names, instead of IP addresses. This is useful since IP addresses change from time to time. In addition, you can define network objects according to MAC address to make the rule application more persistent against network configuration settings. To define a network object: Select Network Objects in the Advanced page. Page 87 ...
Page 92 To define a network object, click Add. The Edit Network Objects page displays. In the Description field, enter a name for the network object. Click Add. The Edit Item page displays. Select the type of network object as IP address, IP subnet, IP range, MAC address, host name, DHCP option, or protocol, and click Apply to save changes. Repeat the above steps to create additional network objects. When complete, click Apply to save changes. Page 88 ...
Page 93: Universal Plug And Play
Universal Plug and Play You can use Universal Plug and Play (UPnP) to support new devices without configuring or rebooting your Gateway. In addition, you can enable the automatic cleanup of invalid rules. When enabled, this functionality verifies the validity of all UPnP services and rules every five minutes. Old and unused UPnP defined services are removed, unless a user‐defined rule depends on it. UPnP services are not deleted when disconnecting a computer without proper shutdown of the UPnP applications, such as messenger. Services may often not be deleted and eventually this leads to the exhaustion of rules and services, and no new services can be define. The cleanup feature locates the invalid services and removes them, preventing services exhaustion. To access this setting: Select Universal Plug and Play in the Advanced page. To enable UPnP and allow UPnP services to be defined on any network hosts, select the UPnP Enabled check box. To enable automatic cleanup of invalid rules, select Enable Automatic Cleanup of Old Unused UPnP Services check box. Click Apply to save changes. Page 89 ...
Page 94: Igmp Proxy
IGMP Proxy You can configure IGMP proxy settings, as needed. To define the settings: Select ICMP Proxy in the Advanced page. Page 90 ...
Page 95 In the IGMP Proxy field, verify IGMP Proxy is enabled. In the Querier Configuration section, define the following fields, as needed: IGMP Version ‐ select the IGMP Proxy version as IGMP, IGMPv2, or IGMPv3. Fast Leave ‐ activate or deactivate Fast. Robustness ‐ select the level of robustness by entering a number greater than or equal to 1. Query Interval ‐ set the query interval in seconds. The interval must be greater than or equal to 1. Query Response Interval ‐ set the query response interval in seconds. The interval must be greater than or equal to 1. In the Client (Host) Configuration section, define the following fields, as needed: Unsolicited Report Interval ‐ set the unsolicited report in seconds. The interval must be between 1 and 25. Persistent Join Interval ‐ set the persistent join interval in seconds. The interval must be between 1 and 25. Click Apply to save changes. Page 91 ...
Page 96: Port Forwarding Rules
Port Forwarding Rules You can view, modify, and delete port forwarding rules. To access the rules: Select Port Forwarding Rules in the Advanced page. Page 92 ...
Page 97 To edit a protocol rule, click the Edit icon in the Action column. The Edit Service page displays. Modify the Service Name and Service Description, as needed. To modify the current protocol, click the Edit icon in the Action column. To add server ports, click Add Server Ports. Click Apply to save changes. Page 93 ...
Page 98: Routing
Routing You can configure the following settings: • IPv6 – enables IPv6 support. • Routing – manages the routing and IP address distribution rules. • IP Address Distribution ‐ adds computers configured as DHCP clients to the network IPv6 Configuration Control You can configure IPv6 on your wireless network. To configure IPv6: Select IPv6 from the Advanced page. Page 94 ...
Page 99: Routing Settings
Enable IPv6 support. Obtain IPv6 DNS Server address automatically or specify the server address. Specify method for assigning LAN IPv6 addresses. In the Interfaces section, select the enabled interfaces. Click Apply to save changes. Routing Settings You can view the routing and IP address distribution rules as well as add, edit, or delete the rules. To view the rules: Select Routing in the Advanced page. Page 95 ...
Page 100 To add a new Gateway, click Add New Route. Specify the following parameters: Name – select the network type. Destination ‐ enter the destination IP of the destination host, subnet address, network address, or default route. The destination for a default route is 0.0.0.0. Netmask – enter the network mask. This is used in conjunction with the destination to determine when a route is used. Gateway – enter the IP address of your Gateway. Metric – enter a measurement preference of the route. Typically, the lowest metric is the most preferred route. If multiple routes exist to a specific destination network, the route with the lowest metric is used. Click Apply to save changes. Page 96 ...
Page 101: Ip Address Distribution
IP Address Distribution You can easily add computers configured as DHCP clients to the network. The DHCP server provides a mechanism for allocating IP addresses to these hosts and for delivering network configuration parameters to the hosts. For example, a client (host) sends a broadcast message on the network requesting an IP address for itself. The DHCP server then checks its list of available addresses and leases a local IP address to the host for a specific period of time and simultaneously designates this IP address as taken. At this point, the host is configured with an IP address for the duration of the lease. The host can renew an expiring lease or let it expire. If it renews a lease, the host receives current information about network services, as it did during the original lease, allowing it to update its network configurations to reflect any changes that occurred since the first connection to the network. If the host wishes to terminate a lease before its expiration, it sends a release message to the DHCP server. This makes the IP address available for use by other hosts. The DHCP server performs the following functions: • Displays a list of all DHCP host devices connected to your Gateway • Defines the range of IP addresses that can be allocated in the network • Defines the length of time the dynamic P addresses are allocated • Provides the above configurations for each network device and can be configured and enabled or disabled separately for each network device • Assigns a static lease to a network computer to receive the same IP address each time it connects to the network, even if this IP address is within the range of addresses that the DHCP server may assign to other computer • Provides the DNS server with the host name and IP address of each computer connected to the network Page 97 ...
Page 102 To view a summary of the services provided by the DHCP server: Select IP Address Distribution in the Advanced page. DHCP Server Settings You can edit the DHCP server settings for a device. To edit the settings: On the IP Address Distribution page, click the Edit icon in the Action column. The DHCP Settings page opens with the device information displayed. Page 98 ...
Page 103 To enable the DHCP server, select DHCP Server in the IP Address Distribution field. Once enabled, the DHCP server provides automatic IP assignments (IP leases) based on the preset IP range defined below. To configure the DHCP server complete the following fields: Start IP Address – enter the first IP address that your Gateway will automatically begin assigning IP addresses from. Since your Gateway’s default IP address is 192.168.1.1, the default start IP address should be 192.162.1.2. End IP Address – enter the last IP address that your Gateway will automatically stop the IP address allocation. The maximum end IP address range that can be entered is 192.168.1.254. WINS Server – determines the IP address associated with a network device. Lease Time in Minutes‐ assigns the amount of time in minutes that each device is assigned an IP address by the DHCP server when it connects to the network. When the lease expires, the server determines if the computer has disconnected from the network. If it has, the server may reassign this IP address to a newly‐connected computer. Provide Host Name if Not Specified by Client – when activated, your Gateway assigns a default name to the client, if the DHCP client has no host name. Click Apply to save changes. DHCP Connections You can view a list of the connections currently assigned and recognized by the DHCP server. In addition, you can add a new connection with a fixed IP address. Note: The fixed IP address of a device is assigned to the MAC address of the network card installed on the network computer. If this network card is replaced, you must update the device entry in the DHCP Connections list with the MAC address of the new network card. To view a list of computers: On the IP Address page, click Connection List. Page 99 ...
Page 104 To define a new Static Connection with a fixed IP address, click Add Static Connection. Page 100 ...
Page 105 Enter the host name. Enter the fixed IP address to be assigned. Enter the MAC address of the network interface of the computer used with this DHCP static connection. Click Apply to save changes. Page 101 ...
Page 106: Firmware Upgrade
Firmware Upgrade You can perform the following functions: • Firmware Upgrade – upgrades using the Internet or a local computer. • Firmware Restore – rollbacks your firmware to a previous version. Firmware Upgrade Your Gateway offers a built‐in mechanism for upgrading or restoring its firmware without losing custom configuration and settings. You can use either of the following methods: • Upgrading from the Internet – upgrades your Gateway’s firmware by remotely downloading an updated software image file. • Upgrading from a local computer – use a software image file pre‐downloaded to the computer’s disk drive for upgrades To upgrade the firmware: Select Firmware Upgrade in the Advanced page. Page 102 ...
Page 107 Select either Upgrade from the Internet or Upgrade from a Computer in the Network. Automatically Upgrade from the Internet To automatically upgrade: Select from the following options in the Firmware Upgrade page: Automatically Check for New Version and Upgrade Wireless Broadband Gateway – enter the period of time and URL at which to receive the upgrade. Your Gateway checks each time interval for an upgrade and, if an upgrade is available, upgrades the firmware. Automatically Check for New Version and Notify via Email – enter the period of time and URL at which to receive the upgrade. Your Gateway checks each time interval for an upgrade and, if an upgrade is available, sends an email to the email address listed in the System Settings. Automatically Check Disabled – Your Gateway does not automatically check for firmware upgrades. You must manually upgrade the firmware. Page 103 ...
Page 108: Firmware Restore
Click Apply to save changes. Manually Upgrade from the Internet To manually upgrade: Click the Check Now button in the Firmware Upgrade page. If a new version is available, click Force Upgrade. A download process begins. When completed, a confirmation page displays, asking whether to upgrade to the new version. Click Apply to save changes. The upgrade process begins and should require no more than a minute to complete the process. When the upgrade process completes, your Gateway automatically reboots. The new firmware runs, maintaining any custom configurations and settings. Upgrade from Local Computer Only use files with a rmt extension when performing the firmware upgrade procedure. To upgrade from a local computer: To utilize the Upgrade from a Computer in the Network option, first obtain a valid firmware image (file) for your Gateway. In the Upgrade from a Computer in the Network section of the Firmware Upgrade page, click Browse to locate the downloaded firmware file and click Open. Click Upgrade Now to begin the update process. The Firmware Upgrade in process page displays. When the upgrade process completes, your Gateway automatically reboots. The new firmware runs, maintaining any custom configuration and settings. Firmware Restore Firmware Restore allows you to undo changes to your Gateway and restore previous settings. For example, you can use firmware restore if a firmware update does not fit your needs. To restore firmware to a previous version: Select Firmware Restore in the Advanced page. Page 104 ...
Page 109 Click Restore Backup Firmware. Page 105 ...
Page 110: Date And Time
Date and Time You can configure the following settings: • Date and Time Settings – sets the time zone and enables automatic time updates. • Scheduler Rules – limits the activation of firewall rules to specific time periods. Date and Time Settings You can set the time zone and enable automatic time updates. To configure the settings: Select Date and Time in the Advanced page. Page 106 ...
Page 111: Scheduler Rules
Select the local time zone. Your Gateway automatically detects daylight saving times for selected time zone. In the Automatic Time Update section, select the Enabled check to perform an automatic time update. Define the time server addresses by clicking Add. The Time Server Settings page displays. Enter the IP address or domain name of the time server, then click Apply to save changes. Scheduler Rules Scheduler rules are used for limiting the activation of firewall rules to specific time periods. The time periods are either for days of the week or for hours of each day based on activity or inactivity. To define a rule: Verify that the date and time of your Gateway is correct. Select Scheduler Rules in the Advanced page. Page 107 ...
Page 112 Click Add. The Set Rule Schedule page displays. Page 108 ...
Page 113 Enter the name of the rule. In the Rule Settings section, specify if the rule is active at the scheduled time or inactive at the scheduled time. Click the Add Rule Schedule. The Edit Rule Schedule page displays. Select the active or inactive days of the week. To define a new active or inactive hourly range, click New Hours Range Entry. Enter the start and end time, then click Apply to save changes. Click Apply again to save the rule schedule. Page 109 ...
Page 114: Configuration Settings
Configuration Settings You can configure the following configuration settings: • Configuration File – used for file backups and restoring configuration files • System Settings – configures various system and management parameters • Port Configuration – sets up Ethernet ports Configuration File You can use the Configuration File functionality to view, save, and load configuration files. These files are used to backup and restore the current configuration of your Gateway. Only configuration files saved on a specific Gateway can be applied to that Gateway. You cannot transfer configuration files between Gateways. WARNING! Manually editing a configuration file can cause your Gateway to malfunction or become completely inoperable. To save or load the configuration file: Select Configuration File. Page 110 ...
Page 115: System Settings
To save the current configuration to a file, click Save Configuration File. The configuration file is saved to you web browser’s download folder. To load a previously saved configuration file, click Load Configuration File. Browse to the location of the file, then click Apply to begin the configuration uploading process. Your Gateway will automatically restart with that configuration. System Settings You can configure various system and management parameters. To configure system settings: Select System Settings in the Advanced page. Page 111 ...
Page 116 In the Router Status section, configure the following: Wireless Broadband Route’s Hostname – enter the host name or URL address of your Gateway. Both names are the same. Local Domain – enter the local domain of the network. In the Wireless Broadband Router section, configure the following by selecting the check box: Automatic Refresh of System Monitoring Web Pages – activates the automatic refresh of system monitoring web pages. Prompt for Password when Accessing via LAN – causes your Gateway to ask for a password when trying to connect to the network. Warn User Before Configuration Changes – activates user warnings before network configuration changes take effect. In the Session Lifetime field, specify the length of time required before reentering a user name and password after your Gateway has been inactive. In the Configure a Number of Concurrent Users field, select the number of users that can access your Gateway at any time. Select Remote Administration to configure the remote administration to your Gateway. In the Management Application Ports section, change the primary and secondary HTTP management ports. In the System Logging section, configure the following system log options: Enable Logging – activates system logging. Low Capacity Notification Enabled – activates low capacity notification. This works in conjunction with the Allowed Capacity before Email Notification and System Log Buffer Size. Allowed Capacity before Email Notification – specify the capacity before an email notification is sent. System Log Buffer Size – specify the size of the system log buffer. Remote System Notify Level – specify the type of information, such as none, error, warning, and information, received for remote system logging. Page 112 ...
Page 117 Page 113 ...
Page 118: Ethernet Port Configuration
In the Security Logging section, configure the following security logging options: Low Capacity Notification Enabled – activates low capacity notification. This works in conjunction with the Allowed Capacity before Email Notification and System Log Buffer Size. Allowed Capacity before Email Notification – specify the capacity before an email notification is sent. System Log Buffer Size – specify the size of the system log buffer. Remote System Notify Level – specify the type of information, such as none, error, warning, and information, received for remote system logging. In the Auto WAN Detection section, specify the DHCP timeout. Click Apply to save changes. Ethernet Port Configuration Ethernet port configuration allows you to set up the Ethernet ports as either full‐ or half‐ duplex ports, at either 10 Mbps, 100 Mbps, or 1000 Mbps. To configure the ports: Select Port Configuration in the Advanced page. Page 114 ...
Page 119 To emulate the speed and duplex configuration of the port with which it’s communicating, select Auto or select the port speed and duplicity. Click Apply to save changes. Page 115 ...
Page 120: Chapter 9 Monitoring Your Gateway
Chapter 9 Monitoring your Gateway System Monitoring displays system information, including basic settings, system log, key network device parameters, and network traffic statistics. Gateway Status You can view the basic settings of your Gateway. To view the basic settings: Select System Monitoring in the Main menu. The Router Status page displays. Page 116 ...
Page 121: Advanced Status
To refresh the page, click Refresh. To continuously refresh the page, click Automatic Refresh On. Advanced Status You can view the details and status of: • System Logging • Full Status/System wide Monitoring of Connections • Traffic Monitoring • Broadband Monitoring To view the advanced status: Select Advanced Status. A warning page displays. Click Yes. The Advanced Status page displays. To view the details of the listed monitoring options, click the link. Page 117 ...
Page 122: System Logging
System Logging System logging provides a view of the most recent activity of your Gateway. In addition, you can view additional logs, such as the security, advanced, firewall, WAN, DHCP, and LAN DHCP. To view the system log: In the Advanced Status page, click the System Logging link. To monitor a specific feature, click the link in the System Log menu in the left column. To enable logging, select the Enable Logging check box to monitor that functionality. To update the data, click Refresh. Page 118 ...
Page 123: Full Status/System Wide Monitoring Of Connections
Full Status/System wide Monitoring of Connections You can view a summary of the monitored data collected for your Gateway. To view your Gateway’s full system status: In the Advanced Status page, click Full Status/System wide Monitoring of Connections. To modify the connection properties, click the individual connection links. To refresh the page, click Refresh. To continuously refresh the page, click Automatic Refresh On. Page 119 ...
Page 124: Traffic Monitoring
Traffic Monitoring Your Gateway continually monitors traffic in the local area network and between the local network and the Internet. You can view up to the second statistical information about data received from and transmitted to the Internet as well as data received from and transmitted to computers in the local network. To view the traffic monitoring data: In the Advanced Status page, select Traffic Monitoring. To refresh the page, click Refresh. To continuously refresh the page, click Automatic Refresh On. Page 120 ...
Page 125: Bandwidth Monitoring
Bandwidth Monitoring You can view and monitor the recorded bandwidth usage measured in Kbps. To view the bandwidth: In the Advanced Status page, select Bandwidth Monitoring. To refresh the page, click Refresh. To continuously refresh the page, click Automatic Refresh On. Page 121 ...
Page 126: Chapter 10 Troubleshooting
Chapter 10 Troubleshooting This chapter lists solutions for issues that may be encountered while using your Gateway as well as frequently asked questions. Note: The advanced settings should only be configured by experienced network technicians to avoid adversely affecting the operation of your Gateway and your local network. Troubleshooting Tips Accessing your Gateway if you are locked out If your Gateway connection is lost while making configuration changes, a setting that locks access to your Gateway’s GUI may have inadvertently been activated. The common ways to lock access to your Gateway are: • Scheduler If a schedule has been created that applies to the computer over the connection being used, your Gateway will not accessible during the times set in the schedule. • Access Control If the access control setting for the computer is set to block the computer, access to your Gateway is denied. To gain access, restore the default settings to your Gateway. Restoring your Gateway’s default settings There are two ways to restore your Gateway’s default settings. It is important to note that after performing either procedure, all previously save settings on your Gateway will be lost. • Using the tip of a ballpoint pen or pencil, press and hold the Reset button on the back of your Gateway for three seconds. • Access the GUI and navigate to the Advanced Settings page. Select the Restore Defaults option. After saving your configuration, if desired, click the Restore Defaults button. For additional details, refer to the Restore Defaults section of this guide. Page 122 ...
Page 127 LAN connection failure To troubleshoot a LAN connection failure: • Verify your Gateway is properly installed, LAN connections are correct, and that the Gateway and communicating network devices are all powered on. • Confirm that the computer and Gateway are both on the same network segment. If unsure, let the computer get the IP address automatically by initiating the DHCP function, then verify the computer is using an IP address within the default range of 192.168.1.2 through 192.168.1.254. If the computer is not using an IP address within the correct IP range, it will not connect to your Gateway. • Verify the subnet mask address is set to 255.255.255.0. Timeout error occurs when entering the URL or IP address Verify the following: • All computers are working properly. • IP settings are correct. • Gateway is on and connected properly. • Gateway settings are the same as the computer. Front Lighted Indicators Flash Speed • Slow flash – Two times per second • Fast flash – Four times per second Power/Internet Light Gateway is starting • Slow flash white Gateway is powered on and connected to the Internet • Solid white ...
Page 128 Wireless Light Wi‐Fi is on • Solid white Additional Functions when pressing WPS button: When the WPS button is pressed, the Wireless Light • Slow flash white slowly flashes white, while waiting for a WPS device to connect. This can require up to two minutes. When a device begins connecting to the Gateway using • Fast flash white WPS, the Wireless Light fast flashes white for two seconds as establishing connection. When a device successfully completes its WPS • Solid white association to the Gateway, the Wireless Light returns to solid white. If an error occurs during Wi‐Fi Protected Setup, the • Fast flash red Wireless Light flashes red rapidly for two minutes. Rear Lighted Indicators Flash Speed • Slow flash – Two times per second • Fast flash – Four times per second WAN Ethernet Indicates no Ethernet link • Unlit Indicates a network link • Solid green Indicates network activity. The traffic can be in either ...
Page 129 LAN Ethernet – Lower LED Indicates no 10/100 Mbps link • Unlit Indicates 10/100 Mbps link • Solid green Indicates LAN activity. The traffic can be in either • Fast flash green direction. LAN MoCA Indicates no MoCA network connection to the device • Unlit Indicates network link • Solid green WAN MoCA Indicates no link to the upstream MoCA device • Unlit Indicates network link • Solid green Page 125 ...
Page 130: Frequently Asked Questions
Frequently Asked Questions I’ve run out of Ethernet ports on my Gateway. How do I add more computers or devices? Plugging in an Ethernet hub or switch expands the number of ports on your Gateway. • Run a straight‐through Ethernet cable from the Uplink port of the new hub to the Gateway. Use a crossover cable if there is no Uplink port/switch on your hub, use a crossover cable. • Remove an existing device from the yellow Ethernet port on your Gateway and use that port. How do I change the password on my Gateway GUI? To change the password: On the Main screen, select Advanced, then select Users. In the Users page, select Admin. The User Settings page displays. In the General section, change the password. Is the wireless option on by default on my Gateway? Yes, your Gateway’s wireless option is activated out of the box. Is the wireless security on by default when the wireless option is activated? Yes, with the unique WPA2 (Wi‐Fi Protected Access II) key that is printed on the sticker on the side of your Gateway. Which connection speeds does your Gateway support? The Ethernet WAN Internet connection supports 100 Mbps. The LAN Ethernet connections support 10/100/1000 Mbps. The 802.11ac wireless connection supports up to 1300 Mbps and the 802.11n supports up to 450 Mbps, depending on signal quality. The MoCA 2.0 connection supports 700 Mbps. Are your Gateway’s Ethernet ports auto‐sensing? Yes. Either a straight‐through or crossover Ethernet cable can be used. Page 126 ...
Page 131 Can I use an older wireless device to connect to your Gateway? Yes, your Gateway can interface with 802.11b, g, n, or ac devices. Your Gateway can be setup to handle only n wireless cards, g wireless cards, b wireless cards, or any combination of the three. Can my wireless signal pass through floors, walls, and glass? The physical environment surrounding your Gateway can have a varying effect on signal strength and quality. The denser the object, such as a concrete wall compared to a plaster wall, the greater the interference. Concrete or metal‐reinforced structures experience a higher degree of signal loss than those made of wood, plaster, or glass. How do I locate the IP address that my computer is using? In Windows 7, click the Windows button and select Control Panel, then click View Network Status and Tasks. In the next window, click Local Area Connection. In the Local Area Network Connection Status window, click Details. On Mac OS X, open System Preferences and click the Network icon. The IP address displays near the top of the screen. My computer cannot connect to the Internet using MoCA. What should I do? A computer cannot be connected directly using a MoCA cable. It must go through a NIM to connect. The NIM converts the MoCA signal to an Ethernet signal the computer can understand. First, check the connection and verify all cables are connected correctly. Then verify the NIM is still connected and check the Ethernet connection to the NIM from the computer. I used DHCP to configure my network. Do I need to restart my computer to refresh my IP address? No. In Windows 7, unplug the Ethernet cable or wireless card, then plug it back in. I cannot access your Gateway GUI. What should I do? If you cannot access the GUI, verify the computer connected to your Gateway is set up to dynamically receive an IP address. I have a FTP or web server on my network. How can I make it available to users on the Internet? For a web server, enable port forwarding for port 80 to the IP address of the server. Also, set up the web server to receive that port. Configuring the server to use a static IP address is recommended. Page 127 ...
Page 132 For a FTP server, enable port forwarding for port 21 to the IP address of the server. Also, set up the web server to receive that port. Configuring the server to use a static IP address is recommended. How many computers can be connected through my Gateway? Your Gateway is capable of 254 connections, but we recommend having no more than 45 connections. As the number of connections increase, the available speed for each computer decreases. Page 128 ...
Page 133: Chapter 11 Specifications
Chapter 11 Specifications The specifications for your FiOS Quantum Gateway are as follows. This includes standards, cabling types, and environmental parameters. Note: The specifications listed in this chapter are subject to change without notice. General Model Number Model: FiOS‐G1100 Standards IEEE 802.3x, 802.3u IEEE 802.11b/g/n/ac IP IP versions 4 and 6 MoCA MoCA WAN: 1350 – 1675 MHz and 975 ‐ 1025 MHz MoCA LAN: 1125 – 1225 MHz Speed Wired WAN Wired LAN Ethernet: 10/100/1000 Mbps auto‐sensing Wireless LAN: 802.11b – up to 11 Mbps 802.11g – up to 54 Mbps 802.11n – up to 450 Mbps 802.11ac – up to 1300 Mbps Page 129 ...
Page 134: Led Indicators
Cabling Type Ethernet 10BaseT: UTP/STP Category 3 or 5 Ethernet 100BaseT: UTP/STP Category 5 Ethernet 1000BaseT: UTP/STP Category 5e Firewall ICSA certified LED Indicators Front Panel Power/Internet, Wi‐Fi Rear Panel WAN Coax, LAN Coax, WAN Ethernet, and LAN Ethernet [4] Environmental Parameters Dimensions and Weight FiOS Quantum Gateway (unit only) Size: 1.87” width x 10” height x 7.4” depth Weight: 1.56 lbs / 0.71 kg Complete System (including packaging) Size: 9.88” / 251 mm width x 3.90” / 99 mm height x 9.57” / 243 mm depth Weight: 2.63 lbs / 1.19 kg Power External, 12V DC, 3.0A Certifications FCC Part 15, UL 60950‐1 Page 130 ...
Page 135 Operating Temperature 10° C to 40° C (50° F to 104° F) Storage Temperature ‐20° C to 85° C (‐4° F to 185° F) Operating Humidity 8% to 95% (non‐condensing) Storage Humidity 5% to 100% (non‐condensing) Page 131 ...
Page 136: Chapter 12 Notices
Chapter 12 Notices This chapter lists various compliance and modification notices, as well as the NEBS requirements and GPL. Regulatory Compliance Notices Class B Equipment This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by implementing one or more of the following measures: • Reorient or relocate the receiving antenna • Increase the separation between the equipment and receiver • Connect the equipment to an outlet on a circuit different from the one to which the receiver is connected • Consult the dealer or an experienced radio or television technician for help Modifications The FCC requires the user to be notified that any changes or modifications made to this device that are not expressly approved by GreenWave Reality, Inc., may void the user’s authority to operate the equipment. Declaration of conformity for products marked with the FCC logo – United States only. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: • This device may not cause harmful interference • This device must accept any interference received, including interference that may cause unwanted operation Page 132 ...
Page 137: Nebs Requirements
Note: To comply with FCC RF exposure compliance requirements, the antenna used for this transmitter must be installed to provide a separation distance of at least 28 cm from all persons and must not be co‐located or operating in conjunction with any other antenna or transmitter. For operation within the 5.15 ~ 5.25 GHz frequency range, this device is restricted to indoor environments. This device meets all the other requirements specified in Part 15E, Section 15.407 of the FCC Rules. For questions regarding your product or the FCC declaration, contact: GreenWave Reality, Inc 39 Parker, suite 100, Irvine, CA – 92618 USA tel: +1 714 805 WAVE (9283) email: na@greenwavereality.com NEBS Requirements The coaxial cable screen shield must be connected to the Earth at the building entrance per ANSI/NFPA 70, the National Electrical Code (NEC), in particular Section 820.93, “Grounding of Outer Conductive Shield of a Coaxial Cable,” or in accordance with local regulation. Warning! The WAN Coax Port is intended for connection to Verizon FiOS only. It must not be connected to any exterior or interior coaxial wires not designated for Verizon FiOS. Page 133 ...
Page 138: General Public License
General Public License This product includes software code developed by third parties, including software code subject to the enclosed GNU General Public License (GPL) or GNU Lesser General Public License (LGPL). The GPL Code and LGPL Code used in this product are distributed WITHOUT ANY WARRANTY and are subject to the copyrights of the authors, and to the terms of the applicable licenses included in the download. For details, see the GPL Code and LGPL Code for this product and the terms of the GPL and the LGPL. Page 134 ...

Frontier FiOS-G1100 User Manual

Chapter 1 Introduction

Chapter 2 Connecting Your Gateway

Chapter 3 Wireless Settings

Chapter 4 Configuring My Network Settings

Chapter 5 Using Network Connections

Chapter 6 Configuring Security Settings

Chapter 7 Setting Parental Controls

Chapter 8 Configuring Advanced Settings

Chapter 9 Monitoring Your Gateway

Chapter 10 Troubleshooting

Chapter 11 Specifications

Chapter 12 Notices

Quick Links

Need help?

Questions and answers

Related Manuals for Frontier FiOS-G1100

Summary of Contents for Frontier FiOS-G1100

Table of Contents