Contents Safety precautions Symbols used ..................General safety precautions ..............Appliance-specific safety precautions ..........Instructions for use ................Disposal Using for the first time Where is the identification plate? ............13 Appliance description Appliance overview ................14 Appliance construction ................15 Operating and display elements ............
Page 4
Programme selection with childproof lock activated ...... 41 End of programme ................. 42 Care and maintenance Cleaning the detergent compartments ..........44 Cleaning the water inlet filter ..............44 Checking the overflow tank ..............45 Emergency draining ................46 Trouble-shooting What to do if …...
Safety precautions Symbols used Denotes important safety precautions. Failure to observe said precautions can result in injury or in damage to the appliance or fittings! Information and precautions that should be observed. Information on disposal Information about the operating instructions Indicates step-by-step instructions.
1 Safety precautions General safety precautions • Read the operating instructions before using the appliance for the first time! • This appliance can be used by children aged 8 and above and by persons with reduced physical, sensory or mental capabilities, or lack of experience and/or knowledge, provided they are supervised or have been instructed on the safe use of the appliance...
Page 7
1 Safety precautions • If an appliance is not equipped with a mains cable and a plug or other means for discon- necting from the mains with a contact opening on each pole complying with the conditions of overvoltage category III for full isolation, an isolating device must be incorporated into the permanently installed electrical installation in accordance with the installation regulations.
1 Safety precautions Appliance-specific safety precautions • Children under 3 years of age must be kept away unless constantly supervised. • The appliance has a maximum dry load capacity of 7 kg.
1 Safety precautions Instructions for use Before using for the first time • The appliance must be installed and connected to the electricity supply in accordance with the separate installation instructions. Have a qualified fitter/ electrician carry out the necessary work. •...
Page 10
1 Safety precautions Caution: Burns hazard! • Textiles that have been cleaned, treated or soaked with flammable chemi- cals, detergents or solvents such as benzene, alcohol, stain remover, oil, paint, wax, etc. are not to be washed in the appliance. Fire or explosion hazard! Wash materials containing such substances first by hand with water or allow the solvent to evaporate completely.
Page 11
1 Safety precautions How to avoid damaging the appliance • Close the appliance door carefully. • Before closing the appliance door and starting a programme, ensure that there are no foreign objects or pets in the washing drum, detergent dispenser drawer or around the foreign body trap. Foreign objects such as coins, nails, paper clips, etc.
Disposal Packaging • All packaging materials (cardboard, plastic film (PE) and polystyrene (EPS)) are marked and should, if possible, be collected for recycling and disposed of in an environmentally friendly way. Disconnection • Disconnect the appliance from the mains. With a fixed appliance, this is to be carried out by a qualified electrician! Safety •...
Using for the first time • The appliance must be installed and connected to the electricity supply in accordance with the separate installation instructions. Have a qualified fitter/ electrician carry out the necessary work. The appliance was tested with water before being shipped. There may therefore still be traces of water left in the appliance.
4 Appliance description Appliance construction 1 Operating and display elements 2 Lid 3 Loading opening 4 Drain tray 5 Foreign body trap 6 Emergency door release tool 7 Emergency door release (for safety reasons blocked when spinning and rinsing) 8 Identification plate / Serial number (FN) 9 Quick operating instructions 10 Overflow tank 11 Drum door...
4 Appliance description Operating and display elements Programme selection buttons Coloureds 60 °C Woollens 30 °C Coloureds 40 °C Hand wash 20 °C Coloureds 20 °C Standard programmes for cotton laundry • 40 °C standard • 60 °C standard • Whites 95 °C Additional programmes Easy care Sprint...
Page 17
4 Appliance description Plain text display 60 °C Coloureds 1h04 Various information appears in the plain text display during the programme selection and the programme sequence. • Programme name with duration • Delayed start • Programme progress with time • User settings remaining •...
Programme overview Main wash programmes Whites 95 °C 1–7 kg White cottons, linens with the fabric care symbol e.g. bed and table linen, towels, white or colour-fast underwear. Coloureds 60 °C 1–7 kg Coloured cottons with the fabric care symbol e.g. bright blouses, overalls, shirts, bed linen.
5 Programme overview Hand wash 20 °C 1–2 kg Very gentle wash for items labelled with the fabric care symbol. Standard programmes for cotton laundry 40 °C standard The most efficient programme for washing normally soiled cotton 1× laundry with the fabric care symbol.
5 Programme overview Additional programmes Easy care Pressing this button activates the easy care programme together with the relevant programme. Wash action and spin speed are reduced. The water level is increased during washing and rinsing. In the case of some programmes, the washing time may be shortened. Whites 95 °C easy care White cottons, e.g.
5 Programme overview Skin protection The «Skin protection» function can be activated together with to the required programme. With this function, two extra rinse cycles are performed and the water level is increased significantly. The «Skin protection» function is particu- larly suitable for people with sensitive skin or with a suspected allergy to washing detergent.
5 Programme overview Sprint Press this button to adapt the programme for a small, lightly soiled everyday wash load (max. 3 kg). Programme Load Spin speed Programme Water Energy selection capacity duration buttons 3 kg 1200 rpm 0h39 50 l 1.0 kWh 3 kg 1200 rpm...
5 Programme overview • normally soiled The washing time of the programme selected is significantly extended. • Anti-mite Anti-mite can be selected with the programmes. The main wash - at the set temperature - is extended and the rinsing is intensified. This func- tion is particularly suitable for individuals with an allergy to mites.
5 Programme overview Additional functions Delayed start The programme start can be delayed from one hour to a maximum of 24 hours. During shut-off periods, which are determined by the local electricity supplier, the delayed start time is extended by the length of time the electricity was shut off.
Page 25
5 Programme overview Fast forward / End of programme Press the button to deselect parts of a programme at any time. • From main wash to rinsing • From rinsing to conditioning • From conditioning to spinning • From spinning to draining Once a programme has started, it is not possible to skip the «Draining»...
User settings Language selection The language in the plain text display can be changed at any time, even if a programme is running. Text in English Press the button repeatedly to change the language to German, French, Italian, Rhaeto-Romanic, English and so on. Childproof lock The childproof lock is to prevent children accidentally starting or stopping a programme.
6 User settings See 'Programme selection with childproof lock activated' for how to operate the appliance when the childproof lock is activated. Automatic door opener If the automatic door opener is switched on, the lid opens automatically at the end of the programme. If the automatic door opener is switched off, the lid End of programme remains closed at the end of the programme.
Washing Preparing the appliance Ensure that the foreign body trap 1 is sitting prop- erly. Plug the appliance in at the mains or turn the wall switch on. Turn on the water tap. If a programme that has already been started has not completely Draining 0h01 finished, press the...
7 Washing Loading the appliance Load dry washing (max. 7 kg). • If washing normally soiled whites and coloureds, fill the washing drum. • If washing heavily soiled whites and coloureds, fill the washing drum max. ¾ full. • If washing easy care cotton fabrics, white and coloured synthetic fabrics as well as mixed fabrics, fill the washing drum max.
7 Washing Adding washing detergent Detergent dosage Adding too much washing detergent can cause excess foaming, giving a poor wash result and, in the worst case, causing damage to the appliance. The amount of detergent required depends on the degree of soiling as well as the wash load, the hardness of the water and the product being used.
Page 31
7 Washing Soap wash Water softener Place on washing drum Soap detergent Add to compartment I Fabric conditioner (softener) Add to compartment II Do not fill with fabric conditioner past the «maximum» mark. Do not use fabric conditioner if drying the washing in a tumble dryer. Tumble drying automatically leaves fabrics soft and fluffy to the touch.
7 Washing After adding the washing detergent Close the lid. Select programme – appears in the plain text display. – The indicator lights for the programme selection buttons flash. – A programme can now be selected. Select programme. If no programme selection is made within 20 seconds, the displays go out. However, it is still possible to make a programme selection.
7 Washing Programme selection «Press and go» The main wash programmes can be started at the press of a single button. The control unit gives the relevant programme information for the different programmes. Select any additional programmes or functions by pressing the relevant buttons.
Page 34
7 Washing Selecting easy care / pre-wash / sport 60 °C Coloureds Biowaschen 1h04 Press the required button while the indicator lights are flashing. – The indicator light for the function selected illuminates. – The likely programme duration appears. Selecting degree of soiling / anti-mite 60 °C Coloureds Biowaschen 1h04...
Page 35
7 Washing Selecting a delayed start Start in 2 hours Immediately after selecting a programme, press the button. Press repeatedly to set the desired delayed start time. – The time set or remaining to the delayed start is displayed. – The plain text display goes dark. –...
Page 36
7 Washing Setting the soaking time Biowaschen 2h00 Soaking After selecting a programme, hold the button depressed and press the button. – A soaking time of 2h00 is shown as a suggestion. To change, press the button repeatedly until the desired soaking time is displayed.
Page 37
7 Washing Selecting bio wash A special programme is available for washing with multi-component detergent. First the alkaline detergent is added to the wash and the suds are heated up 40 °C. Then after around 5 minutes the bleach is added. Bio wash is particularly suitable for removing stubborn protein-based soiling.
Page 38
7 Washing Setting spin speed / stop after rinsing Select programme. 60 °C Coloureds Biowaschen 1h04 Press the button once or more. Spinning at – The new spin speed, e.g. Stop after rinsing , is displayed. – It is possible to change the current setting while a programme is running.
Page 39
7 Washing Setting the refresh programme Select the programmes. Refresh programme 0h18 Press the button repeatedly until appears. Deselecting parts of programmes Press the button repeatedly until the desired part of the programme appears in the plain text display. – The various parts of the programme and the relevant time remaining to the end of the programme are shown in the display.
7 Washing Opening the lid during operation Press the button. Opening door … – is followed by Drum opening position in the plain text display. – The washing drum is automatically returned to the opening position and then the lid is opened. The programme stops and the plain text display flashes.
7 Washing Programme selection with childproof lock activated To operate the appliance with the childproof lock activated, follow the instruc- tions given in this section. However, please note that when activated the child- proof lock can only be overridden by pressing two buttons at the same time. After closing the lid –...
7 Washing End of programme Unloading the washing..with the automatic door opener switched off End of programme – When the programme has finished, appears in the plain text display for 20 minutes. – The indicator light for the programme that has finished remains illumi- nated until the button is pressed.
Page 43
7 Washing Stop after rinsing and unloading After running a programme with stop after rinsing, the water must first be drained off: • Draining with spinning Press the button 1×. – The washing is spun at the preset speed for the programme selected. •...
Care and maintenance Using the correct dosage of detergent will automatically clean the inside of the appliance. Immediately wipe away all traces of detergent with a soft cloth to avoid staining. Cleaning the detergent compartments If the correct dosage of detergent is used, the detergent compartments are cleaned by the water flowing in.
8 Care and maintenance Checking the overflow tank The overflow tank 1 is located at the back of the appliance. If there is an excessive build-up of foam, the foam is diverted to the overflow tank. The tank must be checked periodically and emptied when necessary.
8 Care and maintenance Emergency draining The water in the appliance may be hot - scalding hazard! Allow to cool down before emergency draining. In the event of a blocked water outlet or drain pump during a malfunction or a power failure, if there is water still in the appliance it must be drained off as follows.
Trouble-shooting What to do if … ... in the display appears A2 Check water outlet Possible cause Solution • The foreign body trap or drain Resolve the cause of the problem. pump is blocked. Cancel the error message by pressing •...
Page 48
9 Trouble-shooting ... in the display appears A9 Check water inlet? Possible cause Solution • Water tap is turned off. Fix the problem or wait until the water supply is restored. • Filter in water connection Cancel the error message by pressing blocked (see 'Cleaning the water inlet filter').
Page 49
9 Trouble-shooting ... in the display appears F.. Call service department Possible cause Solution • Various situations can lead to Cancel the error message by pressing a «F» error message. button. Disconnect the power supply for about 1 minute. Switch the power supply back on again and select a new programme.
Page 50
9 Trouble-shooting ... in the display appears U1 Call service department Possible cause Solution • Faulty electrical connection. Note down the error message and then switch off the power supply. Inform the caretaker, the owner of the appliance or the property management company.
Page 51
9 Trouble-shooting ... the programme takes significantly longer than indicated Possible cause Solution • Used too much washing Reduce the amount of detergent used detergent (lengthening the next time. rinsing time). Adjust washing detergent dosage to • Very cold water supply water hardness.
Page 52
9 Trouble-shooting ... the appliance vibrates heavily when spinning Possible cause Solution • Appliance feet are not Optimize the appliance set-up adjusted properly. according to the installation instructions. • Transportation lock has not Remove the transport lock (see 'Trans- been removed. portation lock').
Page 53
9 Trouble-shooting ... traces of washing detergent left behind in the detergent dispenser drawer Possible cause Solution • Damp or lumpy washing Store washing detergent in a dry place. detergent. • Detergent dispenser drawer is Wipe the detergent compartment dry damp and «Delayed start»...
9 Trouble-shooting Opening the lid in the event of a power failure The lid can always be opened by pressing the button, provided there is no power failure. In the event of a power failure (wall switch is «off», coin meter, etc.) the lid can only be opened using the emergency door release.
Page 55
9 Trouble-shooting Turn off water tap. Switch off appliance at wall switch or pull plug out of mains socket. If necessary, carry out emergency draining (see 'Emergency draining'). Fold down drain tray 1. Remove emergency door release tool 2 from fastening. Insert release tool into opening 3 from above.
Washing tips 10.1 Fabric care symbols To wash items correctly, please follow the fabric care symbols on the labels of the wash items. 10.2 Washing detergent The wash temperature selected should agree with the recommended tempera- ture range of the washing detergent to ensure the washing detergent is at its most effective.
10 Washing tips 10.4 Net curtains If washing curtains made from mixed or man-made fibres: • Ask the retailer whether the curtains are machine washable and, if so, at what water temperature. • Fill the washing drum only a quarter full. •...
10 Washing tips 10.5 Energy and water economy • Use the maximum wash load capacity of the particular programme. • Select «Pre-wash» or «Soak» only for washing that is heavily soiled or stained. • For lightly soiled washing without staining select the 20 °C main programme or the additional «Sprint»...
10 Washing tips 10.6 Most efficient programmes … ... for normally soiled cotton laundry at 40 °C Press the button 1× to select the «40 °C standard programme». Load capacity Programme Water Energy Residual duration moisture 3.5 kg 2h15 51 l 0.66 kWh 52 % ...
10 Washing tips 10.7 Unsatisfactory wash results White residue on washing Possible cause Solution • Despite thorough rinsing, Shake out or brush the wash items. badly soluble compounds Wash the items again with just a little (zeolites) in the detergent washing detergent.
Page 61
10 Washing tips Unsatisfactory wash result using detergent for coloureds Possible cause Solution • Exceptionally heavily Select stronger wash programme, e.g. soiled washing. degree of soiling «intensive». • Washing detergent used Use washing detergent containing bleach. (detergents for coloureds) does not contain bleach. Fruit, coffee and tea stains cannot be removed.
10 Washing tips Unsatisfactory rinsing performance Possible cause Solution • Too much washing deter- Adjust washing detergent dosage to water gent. hardness and degree of soiling. • Very «soft» water (below Press the button 3×. 15 °fH). An additional rinsing cycle is carried out. Select skin protection (see Skin protec- tion).
Page 63
10 Washing tips Fabric wear Possible cause Solution • Washing drum over- Put less laundry into the washing drum. loaded. • Friction between fabrics Select the additional «Easy care» during washing. programme. • Pilling. Turn items inside out before washing. Fabric stains Possible cause Solution...
Spare parts Please give product family and exact designation when ordering parts. Water inlet filter Inlet hose 2 m / 3 m Drain hose 1.5 m / 4 m Emergency door release tool Foreign body trap Drain tray...
Technical data 12.1 Dimensions Height: 90 cm Width: 66 cm Depth: 70 cm Weight: 130 kg Load 7.0 kg dry washing capacity: 12.2 Plumbing in Connection to water supply: Cold water G¾" Permitted pressure of water supply: 0.1–0.6 MPa (1–6 bar) Max.
12 Technical data 12.5 Product fiche In accordance with EU Regulation No. 1061/2010 Brand V-ZUG Ltd The model identifier corresponds to the first alphanumerics on the identification plate. Rated capacity for cotton laundry at full load Energy efficiency class Energy consumption of x kWh per year...
Page 67
12 Technical data Programme time of the standard 60 °C mins. cotton programme at full load Programme time of the standard 60°C mins. cotton programme at partial load Programme time of the standard 40°C mins. cotton programme at partial load Duration of the left-on mode mins.
12 Technical data 12.6 Consumption data Whites and coloureds programmes The consumption data and programme durations given serve only as a guide. They refer to the maximum load capacity and can vary with, for instance, towelling material, a very cold water feed, the degree of soiling selected or a smaller wash load.
12 Technical data 12.7 Note for testing institutes Set to the standard programmes according to EN 60456: Standard 40 °C cotton programme Select the «40 °C standard programme» by pressing the button 1×. Standard 60 °C cotton programme Select the «60 °C standard programme» by pressing the button 2×.
Index Additional functions ....... 24 Care ..........44 Cold wash ........24 Care and maintenance Delayed start ......24 Checking overflow tank ... 45 End of programme ....25 Cleaning detergent compart- Fast forward ....... 25 ments ........44 Refresh programme ....24 Emergency draining ....46 Spin speed .........
Page 71
13 Index Easy care ........14, 16 Main wash programmes ....18 End of programme ......16 Maintenance ........44 Stop after rinsing and unloading Model no..........2 ..........43 Most efficient programmes ... 59 Unloading the washing .... 42 End of wash day ......43 Energy and water economy ..58 Net curtains ........57 Note on use ........9...
Page 72
13 Index Queries ..........75 Unloading the washing Quick instructions ......76 ... with automatic door opener switched off ......42 ... with automatic door opener switched on ......42 Refresh ..........14 Unsatisfactory wash result using Repair service ......... 75 detergent for coloureds ..
FN _______________________ Appliance _______________________ Please have these details to hand when contacting V-ZUG in connection with a malfunction. You will find them on the identification plate of your appliance. Open up drain tray. – The identification plate is located next to the emergency door release tool.
Page 76
Clean the detergent compartments Leave the drum door open and the lid slightly ajar Turn off the water tap and power off the appliance V-ZUG Ltd Industriestrasse 66, CH-6301 Zug Tel. +41 (0)41 767 67 67, Fax +41 (0)41 767 61 61 vzug@vzug.ch, www.vzug.com...
Need help?
Do you have a question about the Unimatic T and is the answer not in the manual?
Questions and answers