BullFrog STIL7 Owner's Manual page 23

Once you have completed priming, the home status screen will
display the set temperature. The system requires approximately
1-2 minutes of water flowing through the heater to determine
and display the correct water temperature.
Home/Status Screen
The Home/Status screen on your X Series (X500) control shows
basic statuses including: time, jet status, light status, current water
temperature, spa operation mode, and heating/cooling status. In
addition, many of the basic functions of operating your spa can
be performed with one touch from the Home/Status screen. In
addition, any necessary error or maintenance messages will appear
at the bottom of the screen.
Start or Stop Accessories
To start or stop an accessory (jets, lights, etc.), press the associated
button. Icons will become animated when their accessory is
turned on, and inanimate when turned off. Icons on the screen
will reflect the speed or state of the devices running on your spa.
When an accessory has more than two states, press the button
until it reaches the desired state.
Light Operation
Turn lights on and off using the
lights on. Press again to turn off. Pressing the button repeatedly
will cycle through light modes and colors (flashing, fading, solid
color).
Screen Rotation/Mode Button
From the home status screen you may press the
rotate the screen 180 degrees for easier viewing from inside the spa.
Adjusting the Set Temperature
The water temperature is displayed near the bottom of the home
status screen. Press the
temperature. The set point will appear in large type. Press again
immediately to adjust the set point to your desired temperature.
After 3 seconds without any change to the set temperature value,
the Home/Status screen and with current water temperature in
the upper right will reappear.
When the set value is lower than the current temperature
"Cooling to xx.x" will appear at the bottom of the screen. When
the set value is higher than the current temperature, "Heating to
xx.x" will be indicated. Normally there is a short delay before the
heating starts, during which "Heating suspended" is indicated
under the value. When the water temperature reaches your set
point a message of "Set point reached" will appear.
Spa Settings
The settings on the X Series (X500) control pad are navigated by
the use of the (Settings) button. One press gives you access
to several menus where you can manage the specific settings of
your spa. After pressing the Settings button you may navigate
button. Press once to turn
button to
and buttons to set the desired
to each submenu by pressing the
using the (Light) button to select a submenu.
When using the Settings menu or submenus the screen will
revert back to the Spa mode and Home/Status screen if no key
is pressed for 60 seconds. Note that if an accessory is not present
in your spa configuration, its menu will not appear. Refer to
the following section to get details about the possible settings,
accessories, and their detailed functionalities.
Water Care
The Water Care submenu will help you set up your ideal filtration
and heating settings. Choose from Away from Home, Standard
- Beginner, Energy saving, Super energy saving, and Weekender,
depending on your needs and preferences.
Use the (Light) button to select your setting. A check mark
will appear within the selected icon to confirm your selected
mode.
In the descriptions of each mode below "Economy mode" means
that the set point will be reduced by 20°F*, which means that the
heating system will not be engaged unless the temperature falls to
20°C below the spa's set temperature.
The filtration schedule shown on the screen will apply to the main
filtration pump. If your spa uses a circulation pump configured to
run 24 hours, the screen will show you the purge setting instead
of filtration. The purges are pre-programmed for a fixed number
of minutes, therefore the duration will be set to N/A on the
screen, and only the start time can be modified.
Water Care Modes
Away: In Away mode the spa temperature set point will be
reduced by 20°F (7°C) (see description of "Economy mode"
above). Spa will remain in Economy mode at all times of the day
and all days of the week.
Standard - Beginner: In Standard mode the spa will heat to the
set point and filter according to the spa's standard configuration.
Spa will heat to set point at all times and all days of the week.
Energy Savings: In Energy Savings mode the spa temperature
set point will be reduced by 20°F (7°C) (see description of
"Economy mode" above) during peak daytime hours. Spa will
heat to normal set point during evening hours and on the
weekend.
Super Energy Savings: In Super Energy Savings mode the
spa temperature set point will be reduced by 20°F (7°C) (see
description of "Economy mode" above) during peak daytime
hours. Spa will heat to normal set point during evening hours,
every day of the week.
Weekender: In Weekender mode the spa temperature set
point will be reduced by 20°F (7°C) (see description of
and buttons and then
22