Advertisement
Table of Contents
Included
Included:
Rewinder
Rewinder
Base plate
Base plate
Power supply
Power supply
Power Cord
Power Cord
Thumb nuts
Thumb
Operating Instructions
Operating Instructions
Operating Instructions
Assembly instructions
Assembly instructions
Assembly instructions
1. Install base plate
1.
Install base plate
Lift front of printer and slide base plate into place, aligning front feet of
Lift front of printer and slide base plate into place, aligning front feet of
Lift front of printer and slide base plate into place, aligning front feet of
Lift front of printer and slide base plate into place, aligning front feet of
Lift front of printer and slide base plate into place, aligning front feet of
Lift front of printer and slide base plate into place, aligning front feet of
Lift front of printer and slide base plate into place, aligning front feet of printer with holes in base plate.
Standoffs on base plate need to be facing upwards.
Standoffs on base plate need to be facing upwards.
Standoffs on base plate need to be facing upwards.
Standoffs on base plate need to be facing upwards.
Standoffs on base plate need to be facing upwards.
2.
2. Place rewinder on top of base plate, aligning standoffs with
Place rewinder on top of base plate, aligning standoffs with
Place rewinder on top of base plate, aligning standoffs with
Place rewinder on top of base plate, aligning standoffs with the slots
Place rewinder on top of base plate, aligning standoffs with
3. Line up the sides of the base plate with the sides of the rewinder base
3.
Line up the sides of the base plate with the sides of the rewinder base
Line up the sides of the base plate with the sides of the rewinder base
Line up the sides of the base plate with the sides of the rewinder base
Line up the sides of the base plate with the sides of the rewinder base plate.
Line up the sides of the base plate with the sides of the rewinder base
4. Install thumb
4.
Install thumb nuts.
5.
5. Plug in power adapter to the rewinder and to the AC outlet.
Plug in power adapter to the rewinder and to the AC outlet.
Plug in power adapter to the rewinder and to the AC outlet.
Plug in power adapter to the rewinder and to the AC outlet.
Plug in power adapter to the rewinder and to the AC outlet.
L801 Rewinder
L801 Rewinder Operating Instructions
L801 Rewinder
Operating Instructions
Operating Instructions
Operating Instructions
the slots in rewinder base plate
in rewinder base plate
in rewinder base plate
printer with holes in base plate.
printer with holes in base plate.
plate.
Advertisement
Table of Contents
Related Manuals for Afinia L801
Summary of Contents for Afinia L801
- Page 1 L801 Rewinder L801 Rewinder L801 Rewinder Operating Instructions Operating Instructions Operating Instructions Operating Instructions Included Included: Rewinder Rewinder Base plate Base plate Power supply Power supply Power Cord Power Cord Thumb Thumb nuts Operating Instructions Operating Instructions Operating Instructions Assembly instructions...
- Page 2 Operation 1. Install an empty core on the rewinder; the same width as the stock you are running. 2. Install outer plate. 3. Tighten down the core by turning the dial on the motorized core holder counter clockwise. 4. Place the core holder into the rewinder, matching black to black and gray to gray. 5.
- Page 3 6. Start a roll to roll print job on the L801 printer. After about 3 feet of stock has been printed, pause the printer by pressing the pause button on the front panel. 7. Wind the stock under the dancer arm and tape it to the front of the empty core on the rewinder.
- Page 4 Calibrating the rewinder Please note: The system is already calibrated at the factory. Follow this procedure only if the rewinder is not working correctly. 1. Confirm power is turned off to the rewinder. 2. Insert the motorized core holder into the rewinder (black to black, gray to gray) 3.
- Page 5 4. Insert a straightened paperclip into the hole on the side with the power switch and two LEDs. This will engage a button inside the rewinder. Keep the button pressed and turn on the device. The yellow LED will be flashing. Remove the clip.
- Page 6 6. Move the tension arm about 2/3 of the way to the top and insert the clip to press the button again. The green LED will be flashing. NOTE: This sets the stop position. 7. Move the tension arm to the highest position and insert the clip to press the button again. The holder will start rotating.
Need help?
Do you have a question about the L801 and is the answer not in the manual?
Questions and answers