Table of Contents
Advertisement
Aruba 303P Series Campus Access Points
Installation Guide
The Aruba 303P Series campus access points support IEEE802.11ac Wave 2, delivering high performance with
the MU-MIMO (Multi-User Multiple-Input, Multiple-Output) technology, while also supporting 802.11a/b/g /n
wireless services. The 303P Series access points can be deployed in either a controller-based (ArubaOS) or
controller-less (InstantOS) deployment mode.
The 303P Series access points provide the following capabilities:
IEEE 802.11a/b/g/n/ac operation as a wireless access point
IEEE 802.11a/b/g/n/ac operation as a wireless air monitor
Compatibility with IEEE 802.3af PoE
Integrated Bluetooth Low Energy (BLE) radio
Package Contents
303P Series Access Point
9/16" and 15/16" combined ceiling mount adapter (Spare: AP-220-MNT-C1)
Inform your supplier if there are any incorrect, missing, or damaged parts. If possible, retain the carton, including
the original packing materials. Use these materials to repack and return the unit to the supplier if needed.
Hardware Overview
The following sections outline the hardware components of the 303P Series access points.
Figure 1
System Status
Radio Status
Rev01 | July 2018
303P Series (front view)
1
Advertisement
Table of Contents
Related Manuals for Aruba 303P Series
Summary of Contents for Aruba 303P Series
-
Page 1: Installation Guide
The Aruba 303P Series campus access points support IEEE802.11ac Wave 2, delivering high performance with the MU-MIMO (Multi-User Multiple-Input, Multiple-Output) technology, while also supporting 802.11a/b/g /n wireless services. The 303P Series access points can be deployed in either a controller-based (ArubaOS) or controller-less (InstantOS) deployment mode. - Page 2 The 303P Series access points have two LEDs that indicate the system and radio status of the device. These two LEDs can be configured via ArubaOS or Aruba Instant software into three separate modes: Normal mode (by default): See Table 1 ...
-
Page 3: Ethernet Ports
E1 port by Ethernet cable. If the 303P Series access point is connected to both DC and PoE sources simultaneously, the device will draw power from the DC source, while continuing to draw a minimal current from the PoE source. In the event that the DC power source fails, the access point will switch to the PoE source. -
Page 4: Console Port
The table below indicates the E1 port’s PSE output when the 303P Series access point is connected to DC or PoE power supply. Table 2 AP-303P Power Supply Matrix Power Input on DC Jack or E0 PD Power Output on E1 PSE Port... -
Page 5: Before You Begin
For a complete list of approved channels in your country, refer to the Aruba Downloadable Regulatory Table at www.arubanetworks.com. Verifying Pre-Installation Connectivity The instructions in this section are applicable to the 303P Series access points running ArubaOS only. | Installation Guide Aruba 303P Series Campus Access Points... -
Page 6: Identifying Specific Installation Locations
Refer to the ArubaOS Quick Start Guide for instructions on locating and connecting to the controller. Identifying Specific Installation Locations Use the access point placement map generated by Aruba’s RF Plan software application to determine the proper installation location(s). Each location should be as close as possible to the center of the intended coverage area and should be free from obstructions or obvious sources of interference. - Page 7 4). Make sure that any cable slack is above the ceiling tile. 4. Pushing toward the ceiling tile, rotate the access point clockwise until the device clicks into place on the ceiling tile rail. | Installation Guide Aruba 303P Series Campus Access Points...
-
Page 8: Verifying Post-Installation Connectivity
Electrical and Environmental Specifications For additional specifications on this product, please refer to the product data sheet at www.arubanetworks.com. Electrical Ethernet: 2 x 100/1000 Base-T auto-sensing Ethernet interface (RJ-45) Aruba 303P Series Campus Access Points | Installation Guide... -
Page 9: Regulatory Information
If a power adapter other than the Aruba-approved adapter is used in the US or Canada, it should be NRTL listed, with an output rated 48Vdc, minimum 1A, marked “LPS” and “Class 2”, and suitable for plugging into a standard power receptacle in the US and Canada. -
Page 10: Federal Communication Commission
Luxembourg (LU), Malta (MT), Netherlands (NL), Norway (NO), Poland (PL), Portugal (PT), Romania (RO), Slovakia (SK), Slovenia (SL), Spain (ES), Sweden (SE), Switzerland (CH), Turkey (TR), United Kingdom (UK) Frequency Range MHz Max EIRP 2402-2480 9 dbm Aruba 303P Series Campus Access Points | Installation Guide... - Page 11 If such use is necessary, this equipment and the other equipment should be observed to verify that they are operating normally. Compliance is based on the use of Aruba approved accessories. Refer to the ordering guide for this access point at http://www.arubanetworks.com/assets/og/OG_AP-510Series.pdf.
-
Page 12: Нормативные Требования Евразийского Экономического Союза
1, Телефон/факс: +375 17 392 28 20 ЖШС «Хьюлетт-Паккард (К)», Қазақстан Республикасы, 050040, Алматы к., Бостандык ауданы, Әл-Фараби даңғ ылы, 77/7, Телефон/факс: +7 (727) 355 35 50 Taiwan 第十二條 經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅自變更頻率、加大功率或變更原設計 之特性及功能。 第十四條 低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有干擾現象時，應立即停用，並改善至無干擾時 方得繼續使用。 前項合法通信，指依電信法規定作業之無線電通信。 低功率射頻電機須忍受合法通信或工業、科學及醫療用電波輻射性電 機設備之干擾。 Aruba 303P Series Campus Access Points | Installation Guide... -
Page 13: Contacting Support
Enterprise Company. To obtain such source code, send a check or money order in the amount of US $10.00 to: Hewlett Packard Enterprise Company Attn: General Counsel 3000 Hanover Street Palo Alto, CA 94304 Warranty This hardware product is protected by an Aruba warranty. For more details visit www.hpe.com/us/en/ support.html | Installation Guide Aruba 303P Series Campus Access Points...
Need help?
Do you have a question about the 303P Series and is the answer not in the manual?
Questions and answers