Essilor Mr Blue 2.0 User Manual
  1. Manuals
  2. Brands
  3. Essilor Manuals
  4. Lathe
  5. Mr Blue 2.0
  6. User manual

Essilor Mr Blue 2.0 User Manual

Tracer-centerer-blocker
Hide thumbs Also See for Mr Blue 2.0:
Table of Contents

Advertisement

Quick Links

Download this manual
User Manual

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Mr Blue 2.0 and is the answer not in the manual?

Questions and answers

Related Manuals for Essilor Mr Blue 2.0

Summary of Contents for Essilor Mr Blue 2.0

  • Page 1 User Manual...

  • Page 3: Table Of Contents

    USER MANUAL > CONTENTS CONTENTS INTRODUCTION I. FIRST STEPS WITH MR. BLUE 2.0 1. Descriptive diagrams 2. Instructions for use a. Turning on the tracer-centerer-blocker b. Turning off the tracer-centerer-blocker c. Using the touch screen and keypads d. Tracing screen II.
  • Page 4 USER MANUAL > CONTENTS a. Centering a mid-distance lens using re-marked micro-engravings b. Centering a mid-distance lens using manufacturer markings mode c. Centering a mid-distance lens in manual mode 7. Centering a lens for a high-base frame 8. Markings database a.
  • Page 5 USER MANUAL > CONTENTS 6. Maintain and clean the tracer-centerer-blocker a. Precautions required b. Cleaning the protective glass of the Hartmann plate c. Change the roll of pads IX. M’EYE SIGN AND M’EYE TOUCH 1. The “engraving” function on the tracer-centerer-blocker 2.
  • Page 6 USER MANUAL > CONTENTS...

  • Page 7: Introduction

    A new tracing mode for demo lenses is available for the “Nylor” frame If sphere and cylinder values are present in the job file, they are displayed on the screen in order to avoid the re-entering of the values. Mr Blue 2.0 > v4.0 -09.16...
  • Page 8 USER MANUAL > INTRODUCTION Mr Blue 2.0 > v4.0 -09.16...

  • Page 9: First Steps With Mr. Blue

    I. FIRST STEPS WITH MR. BLUE 2.0...
  • Page 10 USER MANUAL > FIRST STEPS WITH MR. BLUE 2.0 Mr Blue 2.0 > v4.0 -09.16...

  • Page 11: Descriptive Diagrams

    Operating accessory hatch Centering chamber Protective glass Tracing table Pad dispenser Posiblock dispensers (on both sides of the screen) Service accessory hatch Blocking arm Indexer Access to roll of pads Screen tilt buttons Manufacturer plate Connectors Mr Blue 2.0 > v4.0 -09.16...
  • Page 12 White felt tip marker Service accessory hatch Calibration posiblock Pattern gauge (metal) Frame gauge (black, numbered) CD-ROM of calibration gauge data Lower hatches Roll of 22 mm pads Roll of 18 x 14 mm pads Mr Blue 2.0 > v4.0 -09.16...

  • Page 13: Instructions For Use

    To ensure maximum precision and efficiency, the tracer needs 5 minutes to complete its initialisation after its switch-on. Press the two buttons located at the back of the screen to adjust the tilt angle if necessary. Mr Blue 2.0 > v4.0 -09.16...

  • Page 14: Turning Off The Tracer-Centerer-Blocker

    The numeric keypad is displayed for the input of values. Reset the fields Back Confirm Cancel and go back to the work screen The alphanumeric keypad is displayed to save or search for jobs. Mr Blue 2.0 > v4.0 -09.16...

  • Page 15: Tracing Screen

    Job ID Job reference (alphanumeric characters) (p.148) list jobs Collection list d. Tracing screen Work screen indicator Saved jobs list Job list Collection list Information on the job and working mode Settings Devices connected Mr Blue 2.0 > v4.0 -09.16...
  • Page 16 Set up the tracer-centerer-blocker>Customize the tracer>Work mode and display of measurements) (p.113) Job call on Essibox Actions available for the current screen Tracing cycle initialization Detailed functions For more information, consult the section Perform a trace > Tracing environment > Captioned screen. (p.19) Mr Blue 2.0 > v4.0 -09.16...

  • Page 17: Tracing

    II. TRACING...
  • Page 18 USER MANUAL > TRACING Mr Blue 2.0 > v4.0 -09.16...

  • Page 19: The Tracing Environment

    Displaying the tracing completed in binocular mode (p.21) a. Menu screen Dimensions display A: A-dimension B: B-dimension D: D-dimension E: Larger radius from the Boxing center P: Perimeter Function buttons Machine shutdown Tracing screen Centering screen Mr Blue 2.0 > v4.0 -09.16...
  • Page 20 You can configure the tracing for automatic detection. The frame material and type of optical tracing (pattern or demo lens) are detected automatically. To activate automatic detection on tracing, consult the section Configure the tracer-centerer-blocker > Customize the tracer > Action bar. (p.115) Mr Blue 2.0 > v4.0 -09.16...

  • Page 21: Jobs And Working Modes

    The tracing-centering mode (by default) The tracing-tracing mode The selected work mode is shown in the information bar, to the left of the Essilor logo. You can change it in the tracer settings. Working in the tracing - centering mode After tracing, the tracer automatically displays the centering screen.

  • Page 22: Shape Management And Storage

    Creating a job (p.24) Working in current job mode (job A) (p.25) a. Menu screen From the tracing screen or the centering screen, press on the menu then to access the shape storage screen. Mr Blue 2.0 > v4.0 -09.16...
  • Page 23 > The R goes into upper case: > The jobs starting with the letter R are displayed. Select several jobs Press to select several non-consecutive jobs in the list. Example: Press on the button then select jobs #1, #5, #7. Mr Blue 2.0 > v4.0 -09.16...

  • Page 24: Job List

    For further information on data input and use of the keypad, refer to the following section: First steps > First use of the tracer-centerer-blocker > Using the touch screen (p.14) Select the list in which you want to store the job: Mr Blue 2.0 > v4.0 -09.16...

  • Page 25: Working In Current Job Mode (Job A)

    Working in current job mode (job A) As soon as the tracer is initialised, you can work in current job mode: the letter A is displayed by default in the information bar. The job is not saved. Mr Blue 2.0 > v4.0 -09.16...

  • Page 26: Tracing A Rimmed Frame

    For correct tracing of the shape, the frame to be traced must not be deformed and its hinges must be closed. For a small frame, place the two wedges between the tracing table clamps: Mr Blue 2.0 > v4.0 -09.16...
  • Page 27 As part of the tracing of an asymmetrical groove frame (sport or safety frame): make sure to check the position of the groove in the frame. Groove located at the back of the frame Groove located on the front of the frame Mr Blue 2.0 > v4.0 -09.16...

  • Page 28: Tracing A High-Base Frame

    Press to select the first eye to be traced. Select the frame material. Select the type of groove insertion, medium, high or low. Press on to start the tracing cycle. Mr Blue 2.0 > v4.0 -09.16...
  • Page 29 If the frame doesn't stay straight, you can tilt the screen slightly by pressing the two side buttons at the back of the screen. Use the buttons to align the light blue lines with the nasal and temporal ends of the rims. Mr Blue 2.0 > v4.0 -09.16...

  • Page 30: Tracing A Pattern, A Demo Lens Or Recut Lens

    © Press to select the pattern, to select the demo or re-cut lens or to select the lens for a Nylor frame . Press on to start the tracing cycle. Mr Blue 2.0 > v4.0 -09.16...
  • Page 31 Input the curve angle and the frame base, for optimal centering precision Modifying the lens shape For more information, consult the chapter Modifying the lens shape (p.83) Add drilling points on the shape. For more information, consult the chapter Preparing a drilled job (p.91) Mr Blue 2.0 > v4.0 -09.16...

  • Page 32: Mechanical Tracing

    The feeling pressure on the lens being weak, it is pointless to excessively screw down the knurled button. Attaching a pattern to the pattern holder Unscrew the screw holding the pattern-holder tip. Fix the pattern on the pattern-holder tip: Mr Blue 2.0 > v4.0 -09.16...
  • Page 33 Check that the pattern holder does not move in the table. Tracing Press to start the mechanical tracing. To interrupt the tracing at any time, press > The tracer automatically detects the pattern holder. Mr Blue 2.0 > v4.0 -09.16...

  • Page 34: Inputting The Curve And The Frame Base After Monocular Tracing

    Place the frame on the screen: The vertical blue line must be in the center of the frame The plane which is tangent to the two lenses must coincide with the pink line at the bottom. Mr Blue 2.0 > v4.0 -09.16...
  • Page 35 The value is displayed in red. Use the buttons to modify the frame base value. You can also press for a few seconds on the value and change it using the numeric keypad. Press to confirm. Mr Blue 2.0 > v4.0 -09.16...
  • Page 36 USER MANUAL > TRACING Mr Blue 2.0 > v4.0 -09.16...

  • Page 37: Centering A Lens

    III. CENTERING A LENS...
  • Page 38 USER MANUAL > CENTERING A LENS Mr Blue 2.0 > v4.0 -09.16...

  • Page 39: Centering Environment

    > Cleaning the protective glass of the Hartmann plate (p.132) 1. Centering environment This section describes the centering screen and the various centering modes available: Description of the centering screen (p.39) Centering modes (p.41) a. Menu screen Centering screen indicator Mr Blue 2.0 > v4.0 -09.16...
  • Page 40 Provides access to the shape modification screen. For more information, consult the following chapter Modifying the lens shape (p.83) Drilling preparation Provides access to the drilling screen. For more information, consult the chapter Preparing a drilled job (p.91) Mr Blue 2.0 > v4.0 -09.16...

  • Page 41: Centering Modes

    Using the tripods Two accessories are available to ensure better stability of high-curve lenses and small lenses. In the centering chamber, you can thus place: (p.149) the high-base lens tripod (p.149) the recut lens tripod Mr Blue 2.0 > v4.0 -09.16...

  • Page 42: Centering A Single Vision Lens

    Place the stickers recommended by the manufacturer on hydrophobic lenses. This section describes the procedures for the centering of a single vision lens: Centering in automatic mode (p.43) Centering using three focimeter dots (p.45) Centering using re-marked micro-engravings (p.48) Mr Blue 2.0 > v4.0 -09.16...

  • Page 43: Centering A Single Vision Lens In Automatic Mode

    The target moves. Modify the distance between the PRP (point of reference prismatic) and centering cross, if necessary: This value is configured by default at 4 mm for Essilor mid-distance lenses (EyeZen). This value may vary, depending on lens manufacturers.
  • Page 44 Centering a lens > Centering a single vision lens > Lens fit function (p.50) Modify the PD and pupillary height. If modifying the PD and pupillary height results in too great an induced prism, we advise you to order a new lens in the proper diameter. Mr Blue 2.0 > v4.0 -09.16...

  • Page 45: Centering A Single Vision Lens Using Three Focimeter Dots

    Do not make any mark in the lower part of the lens. Press to select the type of single vision lens. Press to select the automatic centering mode using three focimeter dots. > The centering target is displayed: Mr Blue 2.0 > v4.0 -09.16...
  • Page 46 Display of the optical center of the lens (white cross) and boxing center of the shape (blue cross) Display of the sphere power Display of the cylinder power The cylinder angle is displayed: The lens base is displayed: > The lens is centered and ready to be blocked. Mr Blue 2.0 > v4.0 -09.16...
  • Page 47 If modifying the PD and pupillary height results in too great an induced prism, we advise you to order a new lens in the proper diameter. To carry out lens blocking, refer to the section Centering a lens > Blocking a lens (p.80) Mr Blue 2.0 > v4.0 -09.16...

  • Page 48: Centering A Single Vision Lens Using Re-Marked Micro-Engravings

    Enter the half-PD and pupillary height. If necessary, modify the distance between the PRP (prismatic reference point) and the centering cross This value is configured by default at 0 mm for the Essilor single vision lenses. This value may vary, depending on lens manufacturers.
  • Page 49 The lens analysis starts: the tracer searches for the optical characteristics of the lens. > The centered lens is displayed in the work area. > The lens is centered and ready to be blocked. Mr Blue 2.0 > v4.0 -09.16...

  • Page 50: Lens Fit" Function

    Using the "lens fit" function Press > The shape appears in the lens. > The induced prism power is displayed: In green if it allows adequate job results In red if does not allow adequate job results Mr Blue 2.0 > v4.0 -09.16...

  • Page 51: Centering A Single Vision Lens In Manual Mode

    Do not manually center the precalibrated lenses (thickness < 0.8 mm) directly on the window. The lenses would be liable to break during blocking. Take care not to damage the protective glass with glass lenses. Press to zoom. Mr Blue 2.0 > v4.0 -09.16...

  • Page 52: Centering A Progressive Lens

    (p.55) Centering in manual mode (p.57) (p.149) Do not center the precalibrated lenses (thickness < 0.8 mm) in manufacturer markings mode or in re-marked micro-engravings mode, you are likely to break them with blocking. Mr Blue 2.0 > v4.0 -09.16...

  • Page 53: Centering A Progressive Lens Using Re-Marked Micro-Engravings

    Essiclean to remove existing markings. Press to select the type of progressive lens. Press to select automatic centering using re-marked micro-engravings. Mr Blue 2.0 > v4.0 -09.16...
  • Page 54 Enter the half-PD and pupillary height. If necessary, modify the distance between the PRP (prismatic reference point) and the centering cross This value is configured to 4 mm by default for Essilor progressive lenses. This value may vary, depending on lens manufacturers.

  • Page 55: Centering A Progressive Lens Using Manufacturer Markings Mode

    The cross must contain at least three branches: If there is no cross on the lens, draw one using the white felt tip marker. The mark must be surmounted by a full or discontinuous circle. Mr Blue 2.0 > v4.0 -09.16...
  • Page 56 Once the lens is held by the clamps, it must not be handled. To stop centering at any time, press > The lens analysis starts: the tracer searches for the optical characteristics of the lens. Mr Blue 2.0 > v4.0 -09.16...

  • Page 57: Centering A Progressive Lens In Manual Mode

    Description of the centering target Centering cross (white cross) and boxing center of the shape (blue cross) Near vision mark Centering marks Mr Blue 2.0 > v4.0 -09.16...

  • Page 58: Centering Bifocal / Trifocal Lenses

    Place the stickers recommended by the manufacturer on hydrophobic lenses. This section describes the centering procedures for bifocal and trifocal lenses with a round segment or D-segment: Centering in automatic mode (p.59) Centering using three focimeter dots (p.61) Mr Blue 2.0 > v4.0 -09.16...

  • Page 59: Centering A Bifocal Lens In Automatic Mode

    (default value = 0°). Press if you want to modify this value. The numeric keypad is displayed. Enter the desired value, then press to confirm. > The angle value is displayed in the centering screen. Mr Blue 2.0 > v4.0 -09.16...
  • Page 60 You can modify the PD and pupillary height to get the shape to fit into the lens, but if the induced prism is too great, we advice you to order a new lens in the proper diameter. To carry out lens blocking, refer to the section Centering a lens > Blocking a lens (p.80) Mr Blue 2.0 > v4.0 -09.16...

  • Page 61: Centering A Bifocal Lens Using Three Focimeter Dots

    Position the lens in the middle of the centering chamber. Press to start lens tracing. > The clamps close on the lens to hold it in position until its blocking. Once the lens is held by the clamps, it must not be handled. Mr Blue 2.0 > v4.0 -09.16...

  • Page 62: Centering A Bifocal Lens In Manual Mode

    In this mode, the lens is centered in near vision. Prerequisite: The lens must be marked with the focimeter. The three focimeter dots must be: Lined up At the same distance from the central dot 0.5 to 1.5 mm in diameter Mr Blue 2.0 > v4.0 -09.16...
  • Page 63 Take care not to damage the protective glass with glass lenses. Press to zoom. Make sure that the segment is correctly lined up as shown below: Mr Blue 2.0 > v4.0 -09.16...

  • Page 64: Centering An Executive Lens

    (p.66) Centering in manual mode (p.68) (p.149) Do not center the lenses precalibrated (thickness < 0.8 mm) in automatic mode or in three focimeter dots mode, you are likely to break them with blocking. Mr Blue 2.0 > v4.0 -09.16...

  • Page 65: Centering An Executive Lens In Automatic Mode

    The angle value is displayed in the centering screen. Enter the half-PD and pupillary height (for far vision or near vision, depending on your selection). > The target moves. Position the lens in the centering chamber. Press to start centering. Mr Blue 2.0 > v4.0 -09.16...

  • Page 66: Centering An Executive Lens Using Three Focimeter Dots

    At the same distance from the central dot 0.5 to 1.5 mm in diameter Centering the lens Press to select the type of executive lens. Press to select the automatic centering mode using three focimeter dots. Mr Blue 2.0 > v4.0 -09.16...
  • Page 67 Once the lens is held by the clamps, it must not be handled. To stop centering at any time, press > The lens analysis starts: the tracer searches for the optical characteristics of the lens. Mr Blue 2.0 > v4.0 -09.16...

  • Page 68: Centering An Executive Lens In Manual Mode

    At the same distance from the central dot 0.5 to 1.5 mm in diameter Description of the centering target Optical center of the lens (white cross) and boxing center of the shape (blue cross) Centering mark Mr Blue 2.0 > v4.0 -09.16...

  • Page 69: Centering A Mid-Distance Lens

    Place the stickers recommended by the manufacturer on hydrophobic lenses. This section describes the procedures for the centering of a mid-distance lens: Centering using re-marked micro-engravings (p.71) Centering using manufacturer markings mode (p.72) Centering in manual mode (p.74) Mr Blue 2.0 > v4.0 -09.16...
  • Page 70 USER MANUAL > CENTERING A LENS (p.149) Do not center the precalibrated lenses (thickness < 0.8 mm) in manufacturer markings mode or in re-marked micro-engravings mode, you are likely to break them with blocking. Mr Blue 2.0 > v4.0 -09.16...

  • Page 71: Centering A Mid-Distance Lens Using Re-Marked Micro-Engravings

    > The centering target is displayed: Enter the half-PD and pupillary height for near vision. > The target moves. Position the lens in the middle of the centering chamber. Mr Blue 2.0 > v4.0 -09.16...

  • Page 72: Centering A Mid-Distance Lens Using Manufacturer Markings Mode

    To carry out lens blocking, refer to the section Centering a lens > Blocking a lens (p.80) b. Centering a mid-distance lens using manufacturer markings mode Prerequisite: The markings must be clear The lens must at least have the following markings: Mr Blue 2.0 > v4.0 -09.16...
  • Page 73 > The centering target is displayed: Enter the half-PD and pupillary height for near vision. > The target moves. Position the lens in the middle of the centering chamber. Mr Blue 2.0 > v4.0 -09.16...

  • Page 74: Centering A Mid-Distance Lens In Manual Mode

    To carry out lens blocking, refer to the section Centering a lens > Blocking a lens (p.80) c. Centering a mid-distance lens in manual mode Manual centering enables you to center the lenses which: Mr Blue 2.0 > v4.0 -09.16...
  • Page 75 Take care not to damage the protective glass with glass lenses. Press to zoom. Using the re-marked micro-engravings Using the manufacturer markings The cross present on the lens must be superimposed on the target centering cross. Mr Blue 2.0 > v4.0 -09.16...

  • Page 76: Centering A Lens For A High-Base Frame

    Centering a mid-distance lens (p.69) In automatic centering, centering using three focimeter dots, micro-engravings or manufacturer markings, two shapes appear in the work area: Initial shape (without 3D compensation) Corrected shape (with 3D compensation) Examples: Mr Blue 2.0 > v4.0 -09.16...

  • Page 77: Markings Database

    Active eye Select the eye to view the corresponding marking. Display the selected marking Add a new marking Delete a marking Edit a marking IDs 100 to 108 are pre-recorded and cannot be modified. Mr Blue 2.0 > v4.0 -09.16...

  • Page 78: Add A New Marking

    The lens marking is displayed, as well as a blue centering mark. > The far vision mark is selected: Position the blue cross on the point corresponding to far vision using the virtual mouse: Mr Blue 2.0 > v4.0 -09.16...
  • Page 79 Now, record the data for the second eye. Press once the right-eye and left-eye markings have been saved. > The marking has been saved: the next lens with the same marking will automatically be recognised on centering. Mr Blue 2.0 > v4.0 -09.16...

  • Page 80: Blocking A Lens

    The fins of the posiblock must remain visible. The tab of the pad must be lined up with the tab of the posiblock. Always use the pads supplied by Essilor: they are specially designed to ensure the performance of your machine for quality jobs.
  • Page 81 The centering screen for the second lens is displayed. The adjustments made to the PD, pupillary height, type of lens and centering mode are displayed by default for the second lens. Center and block the second lens. Mr Blue 2.0 > v4.0 -09.16...
  • Page 82 USER MANUAL > CENTERING A LENS Mr Blue 2.0 > v4.0 -09.16...

  • Page 83: Modifying The Lens Shape

    IV. MODIFYING THE LENS SHAPE...
  • Page 84 USER MANUAL > MODIFYING THE LENS SHAPE Mr Blue 2.0 > v4.0 -09.16...

  • Page 85: Menu Screen

    Modification of half A-dimensions (temporal / nasal) B-dimension modification Modification of half B-dimensions (upper / lower) Modification of the overall size of the shape Scaling in relation to boxing center Shape rotation around the boxing center Mr Blue 2.0 > v4.0 -09.16...

  • Page 86: Modifying A Shape

    Select the icon showing the part of the shape you wish to decrease or increase. > A red rectangle is displayed around the icon. Use the buttons to reduce or increase the corresponding value and view the modification in real time. Mr Blue 2.0 > v4.0 -09.16...
  • Page 87 Use the buttons to rotate the shape clockwise or anti-clockwise by 1° and view the modification in real time. > The shape swivels: the rotation is applied. > The original shape is displayed in light red. Mr Blue 2.0 > v4.0 -09.16...

  • Page 88: Free-Form Modification

    Move the line starting at the boxing center to orient the modification. Use the buttons to reduce or enlarge the shape. > The shape is modified. > The original shape is displayed in light red. Mr Blue 2.0 > v4.0 -09.16...

  • Page 89: Retouching A Shape

    The types of retouch available vary according to the size of the selected area. Retouch to create a straight line. Retouch to create a curve. Retouch to create an angle. > The selected area is retouched. > The original shape is displayed in light red. Mr Blue 2.0 > v4.0 -09.16...

  • Page 90: Archiving / Saving A Shape

    You can also give it a different ID. Enter a reference for the shape to be saved. Press to confirm. > The shape is archived in a new job with a new ID and is displayed in the shape modification screen. Mr Blue 2.0 > v4.0 -09.16...

  • Page 91: Preparing A Drilled Job

    V. PREPARING A DRILLED JOB...
  • Page 92 USER MANUAL > PREPARING A DRILLED JOB Mr Blue 2.0 > v4.0 -09.16...

  • Page 93: Legend Screen

    (blue) Reference drilling point (by default, the first one created on each side – nasal and temporal) A drilling point with a colour infill indicates non-through drilling Binocular view Active eye The selected eye has an orange frame around it. Type of drilling Hole Slot Notch Mr Blue 2.0 > v4.0 -09.16...

  • Page 94: Configuring A Drilling Point

    Deleting a drilling point (p.97) Dimensioning a drilling point (p.97) Adjusting the position of a drilling point (p.98) The positions of the various drilling points must be set before the centering of the lens. Mr Blue 2.0 > v4.0 -09.16...
  • Page 95 In monocular or symmetric binocular tracing, the drilling points are automatically positioned on both eyes, you can however manage the drilling points on the left side independently of the right side: press  : drilling points are no longer linked Mr Blue 2.0 > v4.0 -09.16...

  • Page 96: Creating A Drilling Point

    The photograph of the demo lens appears to be positioned correctly in the picture of the shape: If the image is badly centered, repeat the operation. Manually position the drill holes of the shape locating them using the photo. Mr Blue 2.0 > v4.0 -09.16...

  • Page 97: Delete One Drilling Point

    > The numeric keypad is displayed. You can also use the buttons to reduce or increase the selected value. Enter the new setting, then press to confirm. > The drilling point has been modified. Mr Blue 2.0 > v4.0 -09.16...

  • Page 98: Adjusting The Position Of A Drilling Point

    The drilling coordinates are those of its entrance drill-hole. For a drill-hole, it is the center. For a slot and a notch, the entrance point is always on the side which is furthest away from the edge of the lens: Mr Blue 2.0 > v4.0 -09.16...
  • Page 99 Y position of the drilling point. > The numeric keypad is displayed. Enter the new value, then press to confirm. > The drilling coordinates have been modified. Mr Blue 2.0 > v4.0 -09.16...
  • Page 100 You can position each drilling point in relation to the reference drilling point by modifying the values in the columns: X coordinates in relation to the reference drilling point  Y coordinates in relation to the reference drilling point To select another drilling point as the reference drilling point: Mr Blue 2.0 > v4.0 -09.16...

  • Page 101: Drilling Models

    The Y coordinates of each drilling point in relation to the boxing center of the model shape The distance between the reference drilling point and the edge of the lens > Two values are displayed under the work area The D-dimension (in mm) you have entered for the tracing Mr Blue 2.0 > v4.0 -09.16...

  • Page 102: Saving A Model

    The new job with the new ID is displayed on the drilling screen. Press to go back to the centering screen. You can go back to the previous job via the shape management screen if it has an ID. Mr Blue 2.0 > v4.0 -09.16...

  • Page 103: Preparing Lens Edging

    VI. PREPARING LENS EDGING...
  • Page 104 USER MANUAL > PREPARING LENS EDGING Mr Blue 2.0 > v4.0 -09.16...

  • Page 105: Menu Screen

    Trivex lens Glass lens Tribrid The configuration of the edging cycles depends on the type of material. An incorrect choice may result in material damage. Type of cycle Standard cycle For all types of material. Mr Blue 2.0 > v4.0 -09.16...

  • Page 106: Edging Settings

    The configuration of the edging cycles depends on the type of material. An incorrect choice may result in material damage. Press to select the type of cycle. Press to select the type of finish. Mr Blue 2.0 > v4.0 -09.16...
  • Page 107 > When you call the shape from the edger, its edging settings will be automatically recovered. Mr Blue 2.0 > v4.0 -09.16...
  • Page 108 USER MANUAL > PREPARING LENS EDGING Mr Blue 2.0 > v4.0 -09.16...

  • Page 109: Tracer-Centerer-Blocker Configuration

    VII. TRACER-CENTERER-BLOCKER CONFIGURATION...
  • Page 110 USER MANUAL > TRACER-CENTERER-BLOCKER CONFIGURATION Mr Blue 2.0 > v4.0 -09.16...

  • Page 111: Configure The Tracer-Centerer-Blocker

    Confirm Press to save the time. Once the settings has been adjusted, press to go back to the work screen. b. Connections The connections are configured from the tracer. Mr Blue 2.0 > v4.0 -09.16...
  • Page 112 They must be set up according to the connected software. Transmission speed Length of frame Parity Stop bit Flow control Test of Internet connectivity Restoration of factory settings. Once the modification is made, press to return to the work screen. Mr Blue 2.0 > v4.0 -09.16...

  • Page 113: Screensaver

    Working mode and measurement display This menu enables you to customize the working mode and display precision of the tracer. To access this menu from your work screen, select > > The following screen is displayed: Mr Blue 2.0 > v4.0 -09.16...
  • Page 114 Select the display or not for the menu “Preparation of the lens for edging” Working mode Select the Working mode by default (if the display of the menu “Preparation of the lens for edging” is selected): I center - I prepare edging Mr Blue 2.0 > v4.0 -09.16...

  • Page 115: Decentration Mode

    Option circled in orange: the option is displayed and selected by default in the action bar (press and hold). To access the customization menu of the action bar from your work screen, select > > The following screen is displayed: Mr Blue 2.0 > v4.0 -09.16...
  • Page 116  : Groove detection carried out systematically The menu is displayed and selected by fault in the action bar (not another possible choice on the work screen), groove detection will be carried out systematically and only on the metal frames. Mr Blue 2.0 > v4.0 -09.16...
  • Page 117 Type of lens Single vision lens Progressive lens Bifocal lens Executive lens Mid-distance lens (Interview) Press to go back to the first page Press to move to the next page Press The following screen is displayed: Mr Blue 2.0 > v4.0 -09.16...

  • Page 118: Restore The Factory Settings

    3. Restore the factory settings At the bottom right of certain settings screens, the button enables you to restore the page's factory settings. Press to cancel and go back to the settings screen. Press to confirm the reset. Mr Blue 2.0 > v4.0 -09.16...

  • Page 119: Maintenance & Servicing

    VIII. MAINTENANCE & SERVICING...
  • Page 120 USER MANUAL > MAINTENANCE & SERVICING Mr Blue 2.0 > v4.0 -09.16...

  • Page 121: Carrying Out The Autotests

    The equipment is operational. A malfunction has been detected; a description is displayed in the message box on the right. Centerer-blocker To test the operation of the centerer-blocker, select > > from your work screen. Mr Blue 2.0 > v4.0 -09.16...

  • Page 122: Checks And Calibration

    Check the centerer-blocker then calibrate it if required (p.124) Calibrate the touch screen (p.125). a. Checking and calibrating the tracing table If you encounter mounting problems, you can check the calibration of the tracing table. Mr Blue 2.0 > v4.0 -09.16...
  • Page 123 The pattern gauge is considered a left lens. For more information on fixing the gauge on the pattern holder, refer to the section Tracing > Tracing a pattern, a demo or re-cut lens > Mechanical tracing (p.32) Select to start the cycle. Wait: a timer is displayed for a few minutes. Mr Blue 2.0 > v4.0 -09.16...

  • Page 124: Checking And Calibrating The Centerer-Blocker

    The test has failed: run the calibration cycles for the height under the lens and the blocker Checking the posiblock release Select the test and press to start the cycle. > An information message is displayed. Mr Blue 2.0 > v4.0 -09.16...

  • Page 125: Calibrating The Touch Screen

    Calibrate the touch screen if your operations have become difficult due to lack of precision. Touch screen malfunction You can directly access the calibration screen without using the settings menu. To do this, press on the centering screen for 5 seconds. Calibrating the touch screen Mr Blue 2.0 > v4.0 -09.16...
  • Page 126 Point precisely on each cross as they are displayed, holding the stylus perpendicular to the screen so as not to alter the calibration. > The settings menu is displayed automatically once the calibration is finished. Press to go back to the work screen. Mr Blue 2.0 > v4.0 -09.16...

  • Page 127: Make A Backup Of The Jobs And The Display Configuration

    Once the backup is performed, a file is created on the backup key: Product number L14XXX - Product serial number XXXXXX- Optician- Date “XX/XX/XXXX”-Time "XXhXXmXXs" Example: It is advisable to backup your jobs regularly. Mr Blue 2.0 > v4.0 -09.16...

  • Page 128: Remote Control" Function

    The product restarts with the selected configuration. 4. “Remote control” Function As part of a maintenance operation, your technical correspondent can remotely control your machine. Check the tracer’s connection to the Internet Press > > > Mr Blue 2.0 > v4.0 -09.16...
  • Page 129 USER MANUAL > MAINTENANCE & SERVICING > The following screen will appear: Press > The following message appears: Press to confirm. If Internet connection is not correct, contact your customer support. Start a session of remote maintenance Press Mr Blue 2.0 > v4.0 -09.16...
  • Page 130 Note the number which is displayed in the center of the screen and communicate it to your technical correspondent. Once the connection is established, a red frame appears around the screen. Press to end the session. Mr Blue 2.0 > v4.0 -09.16...

  • Page 131: Statistics And Technical Log

    Centering operations Blocking operations Calibrations b. Technical history and errors In the work screen of your tracer or edger, select > > to access the list of error messages. The following screen is displayed: Mr Blue 2.0 > v4.0 -09.16...

  • Page 132: Maintain And Clean The Tracer-Centerer-Blocker

    Do not touch the lens on the optical block as this could affect the performance of the tracer. Never clean the tracer with chemical products (e.g. petrol, thinners, solvents). Never clean the machine elements (feeler, tracing table) with a wet rag. Mr Blue 2.0 > v4.0 -09.16...

  • Page 133: Cleaning The Protective Glass Of The Hartmann Plate

    The glass is now clean. c. Change the roll of pads To order new rolls of Essilor pads suited to your digital system, contact the technical department or the sales department. Open the accessory hatch. Press with your thumb on the grey dot, place your fingers under the groove and pull to open the roll compartment.
  • Page 134 USER MANUAL > MAINTENANCE & SERVICING Mr Blue 2.0 > v4.0 -09.16...

  • Page 135: M'eye Sign And M'eye Touch

    IX. M’EYE SIGN AND M’EYE TOUCH...
  • Page 136 USER MANUAL > M’EYE SIGN AND M’EYE TOUCH Mr Blue 2.0 > v4.0 -09.16...

  • Page 137: The "Engraving" Function On The Tracer-Centerer-Blocker

    Ref. manquante the M’EYE Touch function (creative distortion). Ref. manquante Necessary tools before using M’EYE Sign: 1. a Mr Blue 2.0 chain (V8.1 minimum and/or higher version), 2. Essibox: equipped with the 5.1 (minimum) memory version, with “Centered Essibox” setup.
  • Page 138 The following indicators are displayed to indicate that the shape scanned is a creative shape: Centering screen indicator for creative shapes Shape modification screen indicator for creative shapes Drilling screen indicator for creative shapes Mr Blue 2.0 > v4.0 -09.16...

  • Page 139: Technical Data

    TECHNICAL DATA...

  • Page 140: Tracer-Centerer-Blocker

    Cylinder power in diopters: 0.125 D or 0.250 D Cylinder angle: 1° or 5° Shape modification: Scaling, A-dimension, B-dimension, ½ A-dimension, ½ B-dimension, D-dimension modification in one point, rotation Creative modification via the touch screen Mr Blue 2.0 > v4.0 -09.16...

  • Page 141: Environment

    Tracers-centerers-blockers Edgers Essibox RS232C and RJ45 ports Memory update via USB key, external Essilor key or via the Essibox system Integrated auto-maintenance functions (self-calibration, autotests) Size of colour touch screen: 10 inches Dimensions: L 320, D 520, H 700 mm Weight: 25 kg Power supply: 230 V –...
  • Page 142 USER MANUAL > TECHNICAL DATA Mr Blue 2.0 > v4.0 -09.16...

  • Page 143: General Information

    GENERAL INFORMATION...

  • Page 144: Symbols

    The information contained in this document is non-contractual and provided as a guide. It is subject to change without prior notice. Errors or omissions may occur in this type of document, although the greatest care has been taken to ensure the accuracy of the information provided. Essilor cannot be held responsible for any malfunction or loss of data resulting from such errors or omissions.

  • Page 145: Safety Instructions

    Essilor. You acknowledge that the right of use which has been granted to you does not give you any claim to the intellectual property rights of the M’Eye Sign™ brand, which remain the exclusive property of Essilor. The use of the brand must comply with the graphic charter of the brand M’Eye Sign™...

  • Page 146: Limited Liability

    Termination This license is granted for an unlimited time. It may be terminated by you or Essilor with 3 months notice. Your rights rising from this license will be immediately terminated without further notice from Essilor if you do not comply with the conditions of the license. As soon as the license is terminated, you must stop using the Software and Essilor will be authorized to remotely erase the Software from any equipment in your possession, to which Essilor has access (via Essibox®).

  • Page 147: Glossary

    GLOSSARY...
  • Page 148 Example of lenses of this type: Telex lenses The (ID) identifier of job is composed of alphanumerics in the list of jobs and of numbers in the list of the collections. It is unique. Mr Blue 2.0 > v4.0 -09.16...
  • Page 149 Type of lens with distinct correction areas: the upper part of the lens is used for far vision. the lower part of the lens is used for the near vision. TRIPOD FOR HIGH-BASE LENSES Specific tripod to center high-base lenses Mr Blue 2.0 > v4.0 -09.16...
  • Page 150 USER MANUAL > GLOSSARY Mr Blue 2.0 > v4.0 -09.16...
  • Page 151 USER MANUAL > GLOSSARY Mr Blue 2.0 > v4.0 -09.16...
  • Page 152 Essilor Instruments USA 8600 W. Catalpa Avenue, Suite 703 Chicago, IL 60656 Phone: 855.393.4647 Email: info@essilorinstrumentsusa.com www.essilorinstrumentsusa.com...

Table of Contents

Save PDF