Led Indicators - TP-Link Archer VR900 Installation Manual

LED Indicators

LED Status Indication
On System initialization complete.
Flashing System initializing or firmware upgrading is in process.
Power
Do not disconnect or power off the modem router.
Off
Power is off.
On DSL synchronization established.
DSL Flashing DSL synchronization is in progress.
Off DSL synchronization failed.
White Internet connection is available.
Orange No Internet connection or the modem router is operating in
Internet
Bridge mode.
Off The DSL port is not connected or DSL synchronization failed.
Wireless On The 2.4GHz wireless radio band is enabled.
2.4GHz
Off The 2.4GHz wireless radio band is disabled.
Wireless On The 5GHz wireless radio band is enabled.
5GHz
Off The 5GHz wireless radio band is disabled.
On At least one LAN port is connected.
LAN
Off No LAN port is connected.
On The inserted USB device is identified and ready to use.
USB Flashing A new USB device is being identified.
Off No USB device is plugged into the USB port.
On/Off Turns On when a WPS synchronization is established and
automatically turns Off about five minutes later.
WPS
Slow Flashing A wireless device is trying to connect to the network via WPS.
This process may take up to 2 minutes.
Note: You can turn the LEDs on or off by pressing the LED On/Off button.
FAQ (Frequently Asked Questions)
Q1. What can I do if the login page does not appear?
A1. If the computer is set to a static or fixed IP address, change it to obtain an IP address
automatically from the modem router.
A2. Verify http://tplinkmodem.net or 192.168.1.1 is correctly entered in the web browser
and press Enter.
A3. Use another web browser and try again.
A4. Reboot your modem router and try again.
A5. Disable and enable the active network adapter.
Q2. What can I do if the DSL LED does not turn solid on?
A1. Check your cables and make sure they are all plugged in correctly, including the
telephone lines and power adapter.
A2. Restore your modem router to its factory default settings.
A3. Remove the DSL splitter, directly connect the modem router to the phone jack and
follow this Quick Installation to reconfigure the modem router.
A4. Contact your ISP to verify if the DSL line is in good status.
A5. If you have tried all the suggestions above and the problem still exists, contact our
Technical Support.
Button Legend
USB1 USB1 USB2 USB2
Wi-Fi On/O Press to turn both 2.4GHz and 5GHz Wi-Fi on or off.
Power On/O
Press to power on or off the modem router.
DSL LAN2 LAN3 LAN4/WAN
Reset
Press and hold down for at least 5 seconds to reset
the modem router to factory default settings.
WPS Press to start a WPS synchronization.
LED On/O Press to turn the LEDs on or off. LED button is on the
front panel, at the end of all LEDs.
Tether App
To manage your network conveniently on your mobile
device, scan the QR code to download the Tether App.
Q3. What can I do if I cannot access the Internet?
A1. Make sure the telephone and Ethernet cables are plugged in correctly.
A2. Try to log into the web management page of the modem router using the default address
at http://tplinkmodem.net or 192.168.1.1. If you can, try the following answers. If you
cannot, change your computer to obtain an IP address automatically from the modem
router.
A3. Consult your ISP and make sure all the VPI/VCI (or VLAN ID), Connection Type, account
username and password are correct. If they are not, please replace them with the correct
settings and try again.
A4. Restore the modem router to its factory default settings and reconfigure the modem router
by following the instructions in this Quick Installation Guide.
A5. Please contact our Technical Support if the problem still exists.
Q4. What can I do if I forget my password?
Web Management page password:
Restore the modem router to its factory default settings and then set a new password using
1-15 characters.
Wireless Network password:
Features
Ethernet WAN Connection
Connect an Ethernet cable (RJ45) from your fiber or cable modem to the
LAN4/WAN port of the modem router to use it as a wireless router. Refer to
the User Guide for wireless router configuration.
3G/4G Connectivity
Connect a 3G/4G USB mobile broadband modem to the router's USB port
to get wireless Internet access through 3G/4G mobile networks. The USB
dongle can be configured as the primary Internet connection, or as a
backup to enhance network reliability. Refer to the User Guide for
Power
instructions.
USB Features
USB ports can also be used to share a printer, files and media from USB
storage devices over your home network locally, or remotely through the
Internet using its built-in FTP server capability.
To learn more about the USB features, visit
http://tp-link.com/app/usb or scan the QR code.
Remote Access
via FTP Server
A1. The default Wireless Password/PIN is printed on the product label of the modem
router.
A2. If the default wireless password has been changed, log into the modem router's web
management page and go to
Q5. How do I restore the modem router to its factory default settings?
A1. With the modem router powered on, press and
hold down the
of the modem router for at least 5 seconds until
all LEDs turn off momentarily, then release the
button.
A2. Log in to the web management page of the modem router, and go to
System Tools > Backup & Restore, click Factory Restore
process is complete.
USB1 USB1 USB2 USB2
USB 3.0 Ports
Media Local Storage
Sharing Sharing
Basic > Wireless
to retrieve or reset your password.
Reset
button on the back panel
DSL
Reset Button Press & Hold for 5 seconds
Advanced >
and wait until the reset
Printer
Sharing