Suzuki IGNIS Series 2016 Owner's Manual

Table of Contents

Quick Links

Download this manual

ENGLISH

SERVICE STATION INFORMATION

Fuel Recommendation:

See page 1-1

Engine oil recommendation:

(K12C engine models)

Classification: ACEA A1/B1, A3/B3, A3/B4, A5/B5

API SL, SM or SN

ILSAC GF-3, GF-4 or GF-5

Viscosity: SAE 0W-16, 0W-20, 5W-30, 10W-30, 10W-40

(K12M engine models)

Classification: API SG, SH, SJ, SL, SM or SN

Viscosity: SAE 0W-20, 5W-30, 10W-30, 10W-40,

15W-40, 20W-40

For further details, see "Engine oil and filter" in the

"INSPECTION AND MAINTENANCE" section.

Part No. 99011-75RM0-01E August, 2016

Suzuki Red: Magenta 100%, Yellow 100%

Suzuki Blue: Cyan 100%, Magenta 70%

Takumi Blue: Cyan 100%, Black 85%

Black

20.5 mm

Brake Fluid:

DOT3 or SAE J1703

CVT fluid:

SUZUKI CVT FLUID GREEN-2

Tire cold pressure:

See the Tire Information Label located on the

driver's door lock pillar.

Printed in Japan

OWNER'S MANUAL

Keep With Vehicle At All Times.

Contains Important Information

On Safety, Operation & Maintenance.

Table of Contents

Need help?

Do you have a question about the IGNIS Series 2016 and is the answer not in the manual?

Questions and answers

Summary of Contents for Suzuki IGNIS Series 2016

Page 1 Keep With Vehicle At All Times. Contains Important Information On Safety, Operation & Maintenance. Part No. 99011-75RM0-01E August, 2016 Printed in Japan Suzuki Red: Magenta 100%, Yellow 100% Suzuki Blue: Cyan 100%, Magenta 70% Takumi Blue: Cyan 100%, Black 85% Black...
Page 2 NOTE: The illustrated model is one of the IGNIS series. Copyright © 2016 All Rights Reserved No part of this document may be reproduced or transmitted in any form or by any means, electronic or mechanical, for any purpose, without the express written permission of Suzuki Motor Corporation. 75RM0-01E...
Page 3: Before Driving
Please read this manual carefully NOTE: tion in this manual and your vehicle. before operating your new SUZUKI vehicle (For Hong Kong models) SUZUKI MOTOR CORPORATION and review the manual from time to time.
Page 4 Consult your SUZUKI dealer or qualified service NOTICE technician for advice. Indicates a potential hazard that could result in vehicle damage. NOTE: Indicates special information to make maintenance easier or instructions clearer.
Page 5: Operating Your Vehicle
INTRODUCTION Thank you for choosing SUZUKI and welcome to our growing family. Your choice was a wise one; SUZUKI products have great value that will give you driving pleasure for years. This owner’s manual was prepared to give you a safe, enjoyable, and trouble-free experience with your SUZUKI vehicle. In this manual, you will learn about the vehicle’s operation, its safety features and maintenance requirements.
Page 6 A wide variety of non-genuine replacement parts and accessories for SUZUKI vehicles are currently available in the market. Using these parts and accessories can affect the vehicle performance and shorten its useful life. Therefore, installation of non-genuine SUZUKI parts and accessories is not covered under warranty.
Page 7 SERVICE STATION GUIDE 1. Fuel (see section 1) 2. Engine hood (see section 5) 3. Tire changing tools (see section 8) 4. Engine oil dipstick <Yellow> (see section 7) 5. CVT fluid dipstick <Orange> (RHD) (see section 7) 6. Engine coolant (see section 7) 7.
Page 8 MEMO 75RM0-01E...
Page 9: Table Of Contents
TABLE OF CONTENTS FUEL RECOMMENDATION BEFORE DRIVING OPERATING YOUR VEHICLE DRIVING TIPS OTHER CONTROLS AND EQUIPMENT VEHICLE LOADING AND TOWING INSPECTION AND MAINTENANCE EMERGENCY SERVICE APPEARANCE CARE GENERAL INFORMATION SPECIFICATIONS SUPPLEMENT INDEX 75RM0-01E...
Page 10 ILLUSTRATED TABLE OF CONTENTS EXTERIOR, FRONT EXAMPLE 1. Engine hood (P.5-2) 2. Windshield wiper (P.2-124) 3. Roof rails (if equipped) (P.5-11) 4. Outside rearview mirror (P.2-24) 5. Frame hook (P.5-12) 6. Front fog light (if equipped) (P.2-118, 7-51)/ Daytime running light (if equipped) (P.2-117, 7-51) 7.
Page 11 ILLUSTRATED TABLE OF CONTENTS EXTERIOR, REAR EXAMPLE 1. Rear combination light (P.7-53) 2. Radio antenna (P.5-32) 3. Reversing light (P.7-53) 4. Tailgate (P.2-5) 5. Rear window wiper (P.2-126) 6. Fuel filler cap (P.5-1) 7. Rear fog light (if equipped) (P.2-118, 7-54) 8.
Page 12 ILLUSTRATED TABLE OF CONTENTS INTERIOR, FRONT EXAMPLE 1. Electric window controls (if equipped) (P.2-21)/ Electric mirror control switch (if equipped) (P.2-24)/ Outside rearview mirror folding switch (if equipped) (P.2-25) 2. Front passenger’s front air bag (P.2-56) 3. Glove box (P.5-7) 4.
Page 13 ILLUSTRATED TABLE OF CONTENTS 1. Sun visor (P.5-4) VIEW A EXAMPLE 2. Front interior light (P.5-5, 7-49) 3. Stereo camera (if equipped) (P.3-63) 4. Inside rearview mirror (P.2-24) 5. Hands-free microphone (if equipped) (P.5-65) 75RM344 75RM0-01E...
Page 14 ILLUSTRATED TABLE OF CONTENTS 1. Brightness control switch VIEW B EXAMPLE (if equipped) (P.2-69)/ Information switch (if equipped) (P.2-72)/ Trip meter switch (if equipped) (P.2-72) 2. Lighting control lever (P.2-115)/ Turn signal control lever (P.2-122)/ Front fog light switch (if equipped) (P.2-118)/ Rear fog light switch (if equipped) (P.2-118)
Page 15 ILLUSTRATED TABLE OF CONTENTS 1. Instrument cluster (P.2-67)/ VIEW C EXAMPLE Information display (P.2-71, P.2-92) 2. Windshield wiper and washer lever (P.2-124)/ Rear window wiper/washer switch (P.2-126) 3. Hazard warning switch (P.2-124) 4. Front passenger air bag deactivation system indicator (if equipped) (P.2-65)/ Theft deterrent alarm system (if equipped) (P.2-16)/...
Page 16 ILLUSTRATED TABLE OF CONTENTS INTERIOR, REAR EXAMPLE 1. Seat belts (P.2-33) 2. Assist grip (if equipped) (P.5-7) 3. Rear seats (P.2-30) 4. Side curtain air bags (if equipped) (P.2-60) 75RM203 75RM0-01E...
Page 17 ILLUSTRATED TABLE OF CONTENTS LUGGAGE EXAMPLE COMPARTMENT 1. Luggage compartment cover (if equipped) (P.5-11) 2. Accessory socket (if equipped) (P.5-6) 3. Luggage compartment light (if equipped) (P.5-5, 7-49) 4. Jack handle (P.8-1) 5. Wheel brace (P.8-1) 6. Towing hook (P.5-12) 7.
Page 18 ILLUSTRATED TABLE OF CONTENTS MEMO 75RM0-01E...
Page 19 FUEL RECOMMENDATION FUEL RECOMMENDATION Fuel recommendation ............1-1 65D394 75RM0-01E...
Page 20: Fuel Recommendation
Fuel system tive non-automatic system. damage or vehicle performance problems resulting from the use of such fuels are not the responsibility of SUZUKI and may not NOTICE be covered under the New Vehicle War- 75RM304 Be careful not to spill fuel containing ranty.
Page 21 BEFORE DRIVING BEFORE DRIVING Seat belts and child restraint systems ......2-33 Child restraint system for countries applied for UN Regulation No.16 ............2-44 Supplemental restraint system (air bags) ......2-55 Instrument cluster ............... 2-67 Speedometer ............... 2-68 Tachometer (if equipped) ........... 2-68 Fuel gauge ................
Page 22 Ask ignition mode to ON. If you need to make your SUZUKI dealer to have the system spare keys or remote controllers, see your inspected. SUZUKI dealer. The vehicle must be pro-...
Page 23: Door Locks
EXAMPLE • If you lose your immobilizer ignition key Ignition key reminder or remote controller, ask your SUZUKI dealer as soon as possible to deactivate A buzzer sounds intermittently to remind the lost one, and to make a new key or you to remove the ignition key if it is in the remote controller.
Page 24 BEFORE DRIVING To unlock a driver’s door from the outside insert the key in the driver’s door lock Central door locking system of the vehicle, insert the key and turn the and turn the top of the key toward the top of the key toward the rear of the vehi- rear of the vehicle twice.
Page 25 BEFORE DRIVING You can also lock or unlock all doors by NOTE: Dead lock system (if equipped) pressing the front or rear of the switch, • The dead lock system will not operate if respectively. one or more door(s) is (are) not closed This system is designed to help prevent and latched completely.
Page 26 BEFORE DRIVING To activate this system: Child-proof locks (rear door) Tailgate Insert the key in the driver’s door lock and turn the top of the key toward the front of the vehicle twice within 3 seconds. EXAMPLE EXAMPLE You cannot use the lock knobs to unlock the side doors when this system is acti- vated.
Page 27 (4) and lift the tailgate. the tailgate. If the tailgate cannot be unlocked, have the vehicle inspected by your SUZUKI dealer. 62R0366 2) Open the cover (2) in the lock mecha- nism of the tailgate.
Page 28 • If radio wave interference is a con- cern, have the function of the antenna(s) disabled your SUZUKI dealer. 64MS022 Your vehicle is equipped with either a key- less push start system remote controller (Type A) or a keyless entry system trans- mitter (Type B).
Page 29 • If you lose one of the remote controllers, doors are locked with the dead lock sys- dead lock system (if equipped) ask your SUZUKI dealer as soon as pos- tem. If you want to prevent tamper-unlocking of sible for replacement. Have your dealer With the remote controller inside the vehi- the door locks, use this method.
Page 30 BEFORE DRIVING Keyless unlocking/locking using the The turn signal lights will flash once and When the doors are unlocked: request switches the exterior buzzer will sound once when • The turn signal lights will flash twice and the doors are locked, and then the turn sig- the exterior buzzer will sound twice.
Page 31 (1) 80 cm (2 1/2 feet) • If you lose one of the remote controllers, The remote controller is a sensitive ask your SUZUKI dealer as soon as pos- When the remote controller is within electronic instrument. To avoid dam- sible for a replacement.
Page 32 BEFORE DRIVING Request switch warning buzzer Reminder function This exterior buzzer beeps for about 2 sec- EXAMPLE onds in the following conditions to warn you that the request switch is not working: • The request switch is pressed after all doors are closed with the ignition mode changed to ACC or ON by pressing the engine switch.
Page 33 BEFORE DRIVING If the remote controller is left in the vehicle Battery replacement 3) Replace the battery (1) so its + terminal and you lock the driver’s door or front pas- If the remote controller becomes unreli- faces the bottom of the case as shown senger’s door as described below, the door able, replace the battery.
Page 34 Keyless entry system transmitter Used batteries must be disposed of prop- battery, consult your SUZUKI dealer. (Type B) erly according to applicable rules or regu- lations and must not be disposed of with Type A ordinary household trash.
Page 35 • If you lose one of the transmitters, ask “Information display” in this section. your SUZUKI dealer as soon as possible The turn signal lights will flash once when for a replacement. Have your dealer pro-...
Page 36 BEFORE DRIVING Battery replacement WARNING If the transmitter becomes unreliable, replace the battery. Swallowing a lithium battery may cause serious internal injury. Do not To replace the battery of the transmitter: allow anyone to swallow a lithium battery. Keep lithium batteries away from children and pets.
Page 37: Theft Deterrent Alarm System
– The key materials will help to conserve natural – The lock knob on a door resources. For more detailed information – The power door locking switch about disposing of or recycling of the used battery, consult your SUZUKI dealer. 2-16 75RM0-01E...
Page 38 BEFORE DRIVING NOTE: How to arm the theft deterrent alarm NOTE: • The theft deterrent alarm system gener- system (when enabled) • To prevent the alarm from being acci- ates alarms when any of the predeter- Lock all doors (including the tailgate) using dentally triggered, avoid arming it while mined conditions is met.
Page 39 BEFORE DRIVING How to disarm the theft deterrent alarm • If you disconnect the lead-acid battery Enabling and disabling the theft deter- system while the theft deterrent alarm system is rent alarm system Simply unlock the doors using the keyless in the armed condition or the alarm is The theft deterrent alarm system can be push start system remote controller, the...
Page 40 BEFORE DRIVING How to switch the state of the theft 1) Close all the doors and turn the lock deterrent alarm system EXAMPLE knob (1) on the driver’s door in the (Except EU specification vehicle) unlocking direction (2) (rearward). Turn You can switch the theft deterrent alarm the knob on the lighting control lever to system from the enabled state to the dis-...
Page 41: Theft Deterrent Light
BEFORE DRIVING Every time you perform the series of the Theft deterrent light Windows above steps, the state of the theft deterrent alarm system changes from the currently (if equipped) selected one to the other. You can check whether the system is enabled or disabled Manual window control (if equipped) by the number of interior buzzer beeps at EXAMPLE...
Page 42 BEFORE DRIVING Driver’s side (Type B) Passenger’s door Electric window controls (if equipped) EXAMPLE EXAMPLE The electric windows can only be operated when the ignition switch is in “ON” position or the ignition mode is ON. Driver’s side (Type A) EXAMPLE 75RM160 75RM205...
Page 43 BEFORE DRIVING Lock switch (type A) operating any of the switches (2), (3), (4) or (5). To restore normal operation, release EXAMPLE CLOSE the lock switch by pushing it again. WARNING • You should always lock the pas- senger’s window operation when there are children in the vehicle.
Page 44 AUTO-DOWN feature will be tion function. Have your vehicle inspected deactivated, while the AUTO-UP feature by an authorized SUZUKI dealer. may remain activated. The pinching pre- vention function needs to be initialized. 2-23...
Page 45 BEFORE DRIVING When driving at night, you can move the Outside rearview mirrors Mirrors selector tab to the night position to reduce glare from the headlights of vehicles behind you. WARNING Inside rearview mirror Be careful when judging the size or WARNING distance of a vehicle or other object •...
Page 46 BEFORE DRIVING Type B Outside rearview mirror folding Remote folding mirrors (if equipped) switch (if equipped) EXAMPLE When the outside rearview mirrors folding switch is in the unfolded position, the out- side rearview mirrors are folded or EXAMPLE unfolded in conjunction with the door lock- ing or engine switch operation.
Page 47 BEFORE DRIVING NOTE: How to switch the remote folding mir- • If the doors are locked by using the key, rors function lock knob on a door or power door lock- When the ignition mode is LOCK (OFF), 4 times ing switch, the mirrors will not be folded you can switch the function from the automatically.
Page 48: Front Seats
BEFORE DRIVING Front seats System state Number of beeps EXAMPLE Disabled Once Seat adjustment Enabled 2 times WARNING Never attempt to adjust the driver’s • If you cannot complete the operations in seat or seatback while driving. The step 3) and 4) within 15 seconds cor- seat or seatback could move unex- rectly, the state of the remote folding mir- pectedly, causing loss of control.
Page 49 BEFORE DRIVING Head restraints WARNING EXAMPLE Do not place any object under the front passenger’s seat. If an object becomes caught under the front pas- senger’s seat, the following may occur. • The seat will not be latched. • The lithium-ion battery, located under the front passenger’s seat in a model equipped with ENG A- STOP system, will be damaged.
Page 50 BEFORE DRIVING NOTE: Front seat heater (if equipped) It may be necessary to recline the seat- back to provide enough overhead clear- ance to remove the head restraint. Front 86G064 WARNING 75RM005 (1) Left seat heater switch (if equipped) EXAMPLE Improperly using the seat heater can (2) Right seat heater switch (if equipped) be hazardous.
Page 51 BEFORE DRIVING Rear seats NOTICE To avoid damaging the heater ele- ment: Seat adjustment (if equipped) • Do not subject the front seats to heavy impacts, such as children jumping on them. WARNING • Do not cover the seat with any To avoid excessive seat belt slack, insulating materials such as blan- which reduces the effectiveness of...
Page 52 BEFORE DRIVING Rear Head restraints Folding rear seats Head restraints are designed to help The rear seats of your vehicle can be reduce the risk of neck injuries in the case folded forward to provide additional cargo of an accident. space.
Page 53 BEFORE DRIVING Type A NOTICE NOTICE After folding the rear seatback for- • When returning the rear seatback to ward, do not allow any foreign mate- the normal position, check that there rial to enter the lock opening. This is nothing around the striker. Any may cause damage to the inside of foreign materials prevent the seat- the lock and prevent the seatback...
Page 54 BEFORE DRIVING Type B Seat belts and child restraint NOTICE EXAMPLE systems • When returning the rear seatback to the normal position, do not allow any foreign material to enter the lock opening. This may prevent the seatback from being locked securely.
Page 55 BEFORE DRIVING as low as possible across the hips Above the pelvis Across the pelvis 65D606 65D201 65D199 WARNING WARNING WARNING • Never allow persons to ride in the (Continued) (Continued) cargo area of a vehicle. In the event • Seat belts should never be worn •...
Page 56 BEFORE DRIVING Lap-shoulder belt WARNING WARNING (Continued) (Continued) Emergency locking retractor (ELR) • Never use the same seat belt for • For children, if the shoulder belt The seat belt has an emergency locking more than one occupant and never irritates the neck or face, move the retractor (ELR), which is designed to lock attach a seat belt over an infant or...
Page 57 BEFORE DRIVING EXAMPLE Low on hips 60A040 60A036 80J2008 To reduce the risk of sliding under the belt To fasten the seat belt, sit up straight and NOTE: during a crash, position the lap portion of far back into the seat, pull the latch plate The word “CENTER”...
Page 58 BEFORE DRIVING 60A039 To unfasten the seat belt, push the red “PRESS” button on the buckle and retract the belt slowly while holding the belt or/and the latch plate. 2-37 75RM0-01E...
Page 59 BEFORE DRIVING Seat belt reminder With tachometer Without tachometer (1) Driver’s seat belt reminder light / front EXAMPLE EXAMPLE passenger’s seat belt reminder light (if equipped) (2) Rear passenger’s seat belt reminder light (rear left)* (if equipped) (3) Rear passenger’s seat belt reminder light (rear center)* (if equipped) (4) Rear passenger’s seat belt reminder...
Page 60 BEFORE DRIVING When the driver and/or passenger(s) Driver’s seat belt reminder Front passenger’s seat belt reminder do(does) not buckle his or her seat belt, If the driver’s seat belt remains unbuckled (if equipped) the seat belt reminder light will come on or when the ignition switch is turned to “ON”...
Page 61 BEFORE DRIVING • If a seat belt is unfastened when the Shoulder anchor height adjuster Rear outside seat belt guide vehicle speed is more than 15 km/h, the (if equipped) corresponding light will come on and a buzzer will sound. EXAMPLE The reminder will be automatically can- celed when the rear seat belt is buckled or...
Page 62 BEFORE DRIVING Seat belt inspection Child restraint systems WARNING Inspect all seat belt assemblies after EXAMPLE any crash. Any seat belt assembly which was in use during a crash (other than a very minor one) should be replaced, even if damage to the assembly is not obvious.
Page 63 80JC016 tion No.16) Booster seat When purchasing a child restraint and WARNING install it to your SUZUKI vehicle, refer to EXAMPLE (Vehicle without the front passenger the information about suitability for child air bag deactivation system) restraints shown in “Child restraint system...
Page 64 BEFORE DRIVING WARNING (Vehicle with the front passenger air bag deactivation system) When using a child restraint system on the front passenger’s seat, the front passenger’s air bag system must deactivated; otherwise deployment of the front passenger’s air bag could result in the death or serious injury of the child.
Page 65 BEFORE DRIVING Child restraint system for countries applied for UN Regulation No.16 CAUTION Adjust the height of the rear head restraint or remove it for fitting the child restraint, as necessary. However, if a booster cushion not equipped with the head restraint is fitted, the rear seat head restraint should not be removed. If the rear head restraint is removed for fitting the child restraint, you need to install it again after removing the child restraint.
Page 66 =Seat position not suitable for children in this mass group NOTE: 1) SUZUKI recommends “Britax Römer Baby Safe Plus” child seat. SUZUKI Genuine Accessory part number: 990E0-59J37-001 2) Child restraint system with support leg is prohibited in this seating position.
Page 67 BEFORE DRIVING Installation suitability of ISOFIX child restraint systems Vehicle ISOFIX positions Size Mass Group Fixture Front Rear Rear Intermediate Intermediate Others class Passenger Outboard Center Outboard Center sites ISO/L1 N.A. N.A. N.A. N.A. N.A. carrycot ISO/L2 N.A. N.A. N.A. N.A.
Page 68 =ISOFIX position not suitable for ISOFIX child restraint systems in this mass group and/or this size class. NOTE: 1) SUZUKI recommends “Britax Römer Duo Plus” child seat. SUZUKI Genuine Accessory part number: 990E0-59J56-000 2) SUZUKI recommends “Britax Römer KidFix XP” child seat.
Page 69 BEFORE DRIVING Installation suitability of i-Size child restraint systems Seating position Front Rear Rear Intermediate Intermediate Rear Intermediate Passenger Outboard Outboard Outboard Outboard Center Center Outboard Left Right Left Right i-Size Child N.A. N.A. N.A. N.A. N.A. Restraint Key of letters to be inserted in the above table i-U =Suitable for i-Size “universal”...
Page 70 If the child restraint is fitted improp- deactivation system) erly, a child sitting in it could be Whenever possible, SUZUKI recom- injured in a crash. mends that child restraint systems be installed on the rear seat. According to accident statistics, children are safer when...
Page 71 BEFORE DRIVING Install the ISOFIX type child restraint sys- Here is a general instruction: Installation with ISOFIX type tem according to the instructions provided anchorages CAUTION by the child restraint system manufacturer. After installation, try moving the child Adjust the height of the rear head restraint system in all directions especially EXAMPLE restraint or remove it for fitting the...
Page 72 BEFORE DRIVING 3) Push the child restraint toward the anchor- ages so that the connecting bar tips are EXAMPLE EXAMPLE partially hooked to the anchorages. Use your hands to confirm the position. EXAMPLE 78F114 68LM268 1) Place the child restraint in the rear seat, 2) Use your hands to carefully align the inserting the connecting bars to the connecting bar tips with the anchor-...
Page 73 BEFORE DRIVING 1) Remove the luggage compartment cover NOTICE (if equipped). EXAMPLE 2) Secure the child restraint on the rear When installing a child restraint sys- seat using the procedure described tem to the rear seat, adjust the front above for securing a restraint system seat position so that the front seat that does not require a top tether strap.
Page 74 The pretensioner is located in each front tensioner system serviced by an autho- seat belt retractor and both side of the rear rized SUZUKI dealer as soon as possible. seat belt retractor (if equipped). The pre- tensioner tightens the seat belt so the belt If AIR BAG light on the instrument cluster fits the occupant’s body more snugly in the...
Page 75 Have both systems inspected by an authorized SUZUKI dealer as soon as possible. Service on or around the pretensioner sys- tem components or wiring must be per- formed only by an authorized SUZUKI dealer who is specially trained.
Page 76 Supplemental restraint EXAMPLE system (air bags) WARNING This section describes the protection provided by your SUZUKI vehicle’s supplemental restraint system (air bags). Read and follow all instruc- tions carefully to minimize your risk of severe injury or death in the event of a crash.
Page 77 Have the air bag system minor frontal crashes, since they would inspected by an authorized SUZUKI dealer offer no protection in those types of acci- as soon as possible. dents. Since an air bag deploys only one...
Page 78 BEFORE DRIVING Therefore, an air bag is not a substitute for Front passenger’s front air bag seat belts. To maximize your protection, EXAMPLE always fasten your seat belts. Be aware that no system can prevent all possible injuries that may occur in an accident. Driver’s front air bag EXAMPLE 58MS030...
Page 79 BEFORE DRIVING Conditions of front air bags deployment Conditions of front air bags may inflate WARNING (inflation) Receiving a strong impact to the lower body of your vehicle, the front air bags will (Vehicle with the front passenger air inflate in many cases. bag deactivation system) When using child restraint system on the front passenger’s seat, the front...
Page 80 BEFORE DRIVING Front air bags may not inflate The front air bags may not inflate when the impact is absorbed since the crash object moved, vehicle body deformed, or crash angle was greater than about 30 degrees from the front. 80J101 80J119 •...
Page 81 BEFORE DRIVING Side air bags and side curtain air bags (if equipped) EXAMPLE 80J104 80J106 • Crash with a utility pole or stumpage • Frontal crash with a fixed wall that does not move or deform in less than about 25 km/h (15 mph) 68KM090 Side air bags and side curtain air bags are...
Page 82 BEFORE DRIVING to restrain occupants from further move- Side curtain air bags (if equipped) Conditions of side air bags and side ments during the accident. curtain air bags deployment (inflation) EXAMPLE Therefore, an air bag is not a substitute for seat belts.
Page 83 BEFORE DRIVING Side air bags and side curtain air bags Side air bags and side curtain air bags may inflate in a strong impact may not inflate 80J123 • Crash from the side at an angle 80J102 80J121 • Crash from the front 80J124 80J122 •...
Page 84 BEFORE DRIVING Air bags must inflate quickly and forcefully in order to reduce the chance of serious or fatal injuries. However, an unavoidable consequence of the quick inflation is that the air bag may irritate bare skin, such as the facial area against a front air bag. Also, upon inflation, a loud noise will occur and some powder and smoke will be released.
Page 85 Remind anyone who ser- propelled by the air bag in the event vices your SUZUKI vehicle that it has air of a crash. Either of these condi- bags. tions may cause severe injury.
Page 86 After that, only “PASSENGER AIRBAG SUZUKI vehicle. Do not touch air bag sys- OFF” indicator (2) comes on. tem components or wires. The wires are When you activate or deactivate the front wrapped with yellow tape or yellow tubing, passenger’s air bag, check which indicator...
Page 87 Whenever possible, SUZUKI recom- 1) Check that the ignition switch is in mends that child restraint systems be “LOCK” position or the engine switch is installed on the rear seat.
Page 88: Instrument Cluster
BEFORE DRIVING To activate the front passenger’s air bag, Instrument cluster follow the instructions below before start- ing the engine. 1. Speedometer 1) Check that the ignition switch is in “LOCK” position or the engine switch is 2. Tachometer (if equipped) in LOCK (OFF) mode.
Page 89 BEFORE DRIVING Without tachometer Speedometer EXAMPLE The speedometer indicates vehicle speed. NOTE: For models of GCC countries, a buzzer will sound when the vehicle speed exceeds about 120 km/h. This buzzer does not indi- cate a vehicle malfunction. If you slow down to about 118 km/h, the buzzer will stop.
Page 90: Fuel Gauge
BEFORE DRIVING When the ignition switch is in “ON” position Fuel gauge Brightness control or the ignition mode is ON, this gauge gives an approximate indication of the With tachometer When the ignition switch is turned to “ON” amount of fuel in the fuel tank. “F” stands for full and “E”...
Page 91 BEFORE DRIVING With tachometer To increase the brightness of the instru- Without tachometer ment panel lights, push “+” side of the EXAMPLE brightness control switch (1). To change the brightness quickly, push and hold the switch. To reduce the brightness of the instrument panel lights, push “–”...
Page 92 BEFORE DRIVING NOTE: Information display (instrument If you select the maximum brightness level EXAMPLE when the position lights or headlights are cluster with tachometer) on, the following functions will be can- celed. The information display is shown when the • The function which automatically dims ignition switch is in “ON”...
Page 93 BEFORE DRIVING Display (D) Selector position (for CVT models) / EXAMPLE Gear position (for CVT models with man- ual mode or Auto Gear Shift models) / Gearshift indicator (if equipped) Display (E) Trip meter Display (F) Odometer Display (G) Fuel gauge 75RM183 81P31150 (2) Information switch...
Page 94 BEFORE DRIVING Clock Fuel consumption / Driving range / Average speed / Driving time / Total idling stop time (if equipped) / Total idling fuel saved (if equipped) / The display (A) shows the time. Energy flow indicator (if equipped) To set the clock, follow “Setting mode”...
Page 95 BEFORE DRIVING (a) Instantaneous fuel consumption Instantaneous fuel consumption Average fuel consumption (b) Average fuel consumption The display shows instantaneous fuel con- If you selected average fuel consumption (c) Driving range sumption with a bar graph only when the the last time you drove the vehicle, the dis- (d) Average speed vehicle is moving.
Page 96 BEFORE DRIVING To change when the value of average fuel NOTE: Driving time consumption is reset, refer to “Setting • If you refuel when the ignition switch is in The display shows the total amount of driv- mode” in this section. “ON”...
Page 97 BEFORE DRIVING Total idling fuel saved (if equipped) NOTE: Selector position / Gear position / The display shows the total amount (in mil- For Auto Gear Shift models, when the Gearshift indicator liliters) of fuel conservation by ENG A- gearshift lever position and the gear posi- STOP system since the indication was tion indication in the information display The display (D) shows some of the follow-...
Page 98 BEFORE DRIVING Drive mode indicator Trip meter Fuel gauge (for Auto Gear Shift models) When the gearshift lever is in “D”, the dis- The display (E) shows the trip meter. The display (G) shows the fuel gauge. play shows the drive mode indicator (9). Refer to “Fuel gauge”...
Page 99 BEFORE DRIVING NOTE: Eco-driving display Setting mode • You can change the setting so that the Eco-driving display will not be displayed. When you turn the ignition switch to When the ignition switch is in “ON” position For details on the setting mode, refer to “LOCK”...
Page 100 BEFORE DRIVING NOTE: Temperature (Temperature unit setting) Door lock (Door unlock setting) • If you push and hold the information You can change the units that temperature (if equipped) switch (2) to enter the setting mode is displayed in. You can choose either once or twice oper- when the display (C) shows average fuel ation(s) to unlock all doors (including the NOTE:...
Page 101 BEFORE DRIVING NOTE: TPMS Default (initialization setting) For the theft deterrent alarm system of (Tire pressure monitoring system set- If you select “YES” and push the informa- other than Israel and Germany models, ting) (if equipped) tion switch (2), all settings will be reinitial- refer to “Theft deterrent alarm system”...
Page 102 BEFORE DRIVING • When you push and hold the information Warning and indicator messages switch (2) for about 2 seconds while a message is displayed, the message will The display shows warning and indicator disappear temporarily. If the problem messages to let you know about certain that caused the message is not cor- vehicle problems.
Page 103 BEFORE DRIVING Warning and indicator messages All model Warning and indicator Master warning Sound Cause and remedy message indicator light Blinks Beep (one time from interior A door or tailgate is not properly closed. If in (only while vehicle buzzer; only while vehicle is driving, stop the vehicle in a safe place and is in motion) in motion)
Page 104 BEFORE DRIVING Warning and indicator Master warning Sound Cause and remedy message indicator light Beep (one time from interior Fuel is low. Refill it immediately. (#1) buzzer) 75RM213 The road may be icy. Drive very carefully. (#1) 75RM210 (#1) This message will disappear for a while even if the problem that caused the message to appear is not corrected. 2-83 75RM0-01E...
Page 105 There is a problem with the steering lock sys- buzzer) tem. Have your vehicle inspected by an authorized SUZUKI dealer. 61MM0A168 (#1) This message will disappear for a while even if the problem that caused the message to appear is not corrected. 2-84...
Page 106 Beep (one time from interior There is a problem with the keyless push start buzzer) system. Have your vehicle inspected by an authorized SUZUKI dealer. 75RM215 Blinks By certain conditions, some The remote controller may be outside the vehi- kind of sound you will hear cle or its battery may have become discharged.
Page 107 BEFORE DRIVING Warning and indicator Master warning Sound Cause and remedy message indicator light Blinks Beep (one time from interior The steering lock is not disengaged. While buzzer) lightly turning the steering wheel in both direc- tions, press the engine switch again. 75RM219 The remote controller battery is about to become flat.
Page 108 BEFORE DRIVING Warning and indicator Master warning Sound Cause and remedy message indicator light Auto Gear Shift The engine switch is pressed with the gearshift lever in a position other than “N” and depress- ing the brake pedal. Try again as instructed by message.
Page 109 BEFORE DRIVING CVT model Warning and indicator Master warning Sound Cause and remedy message indicator light Blinks Beep (one time from interior The CVT fluid temperature becomes too high. buzzer) Stop the vehicle in a safe place and let the fluid cool down.
Page 110 Beep (one time from interior There may be a problem with ESP system. buzzer) Have your vehicle inspected by an authorized SUZUKI dealer. 75RM223 Hill Hold Control System Blinks Beep (one time from interior There may be a problem with hill hold control buzzer) system.
Page 111 BEFORE DRIVING Vehicle with ENG A-STOP system Warning and indicator Master warning Sound Cause and remedy message indicator light The engine does not stop automatically by the ENG A-STOP system, because any of the auto stop conditions is not met. Refer to “ENG A-STOP system (engine auto stop start system)”...
Page 112 BEFORE DRIVING Warning and indicator Master warning Sound Cause and remedy message indicator light By certain conditions, some The engine restarts automatically, because the kind of sound you will hear brake booster vacuum pressure is low, the from interior of the vehicle. driver’s door is opened, the driver’s seat belt is unfastened or other reason.
Page 113 BEFORE DRIVING When the ignition switch is in “ON” posi- Selector position / Gearshift indicator Information display (instrument tion, the information display shows the fol- lowing information. cluster without tachometer) The display (B) shows some of the follow- ing indications. Display (A) Fuel gauge EXAMPLE...
Page 114 BEFORE DRIVING (a) Trip meter A Trip meter / Odometer / (b) Trip meter B EXAMPLE Fuel consumption / Driving range / (c) Odometer Oil indicator (d) Instantaneous fuel consumption (e) Average fuel consumption The display (C) shows one of the following (f) Driving range indications, trip meter A, trip meter B, odometer, instantaneous fuel consump-...
Page 115 BEFORE DRIVING Trip meter Instantaneous fuel consumption Average fuel consumption The trip meter can be used to measure the The display shows the value of instanta- If you selected average fuel consumption distance traveled on short trips or between neous fuel consumption only when the the last time you drove the vehicle, the dis- fuel stops.
Page 116: Inspection And Maintenance
AND MAINTENANCE” section or consult value of driving range will be shown after reinitialized. Change the unit again to your SUZUKI dealer for advice on appro- driving for a while. your preference. priate procedure of engine oil and oil filter maintenance.
Page 117 The thermometer indicates the outside For the resetting procedure, it is recom- oil indicator will go out and then the dis- temperature. mended to consult your SUZUKI dealer. If play indicates odometer. you reset it by yourself, follow the proce- EXAMPLE...
Page 118 BEFORE DRIVING When the display (C) shows the driving NOTE: Clock range, you can change the unit of tem- When you reconnect the negative (–) ter- perature. minal to the lead-acid battery, the clock The display (E) shows the time. To change the unit of temperature, while indication will be reinitialized.
Page 119 BEFORE DRIVING Setting mode In the setting mode, you can set up the following functions. Indication Functions Time indication of clock “ ” Central door locking system “ ” Additional flashes of the turn signal “ ” Oil change request light reset setting “ ”...
Page 120 BEFORE DRIVING Time indication of clock “ ” Initialization setting “ ” • : 12-hour format (default set- • Initialize all settings Turn the indicator selector knob ting) (2). • : 24-hour format EXAMPLE Central door locking system “ ” Push the indicator selector •...
Page 121: Warning And Indicator Lights
TPMS malfunction. driving, have your vehicle inspected When the system detects a malfunction, by an authorized SUZUKI dealer. this light will blink for about 75 seconds Even if the light turns off after blink- and then remain continuously illuminated.
Page 122: Emergency Service
BEFORE DRIVING WARNING WARNING WARNING The load-carrying capacity of your Continuing to drive with the low tire (Continued) tires is reduced at lower inflation pressure warning light on can lead to • If your vehicle is equipped with a pressures. If your tires are even mod- an accident, resulting in severe injury flat tire repair kit instead of a spare erately under-inflated, the load on the...
Page 123: Specifications
If any of the following conditions the vehicle’s brake system. occur, you should immediately ask If this happens: your SUZUKI dealer to inspect the 1) Pull off the road and stop carefully. brake system. • If the brake system warning light...
Page 124 If one of the above occurs, have the sys- light is working. If the light stays on or tem inspected by your SUZUKI dealer. comes on when driving, there may be If the ABS becomes inoperative, the brake ®...
Page 125 If the hill If there is enough oil, the lubrication sys- descent control indicator blinks, the hill ® tem should be inspected by your SUZUKI For details of the ESP systems, refer to descent control will not be activated.
Page 126 SUZUKI dealer. WARNING If AIR BAG light does not blink or come on briefly when the ignition switch is turned to “ON”...
Page 127 Stop tem. the vehicle in a safe place and let the sys- Bring the vehicle to your SUZUKI dealer to tem cool down. have the damage fixed. If the CVT fluid temperature becomes too (For EU specification vehicle) high, this light will blink.
Page 128 If this happens, press the engine switch, turning the steering wheel to the NOTE: right or left. If this light still stays on, ask your SUZUKI dealer to have the system The activation point of this light varies inspected. depending on road conditions (for exam- ple, slope or curve) and driving conditions because of fuel moving in the tank.
Page 129 Avoid driving conditions that may lead to erly. Have the system inspected by your actual overheating. If the light stays on SUZUKI dealer. without blinking, then the engine is over- heating. Follow the instructions in “Engine NOTE: trouble: Overheating”...
Page 130 Bring For details, refer to “Dual camera brake sup- the dual camera brake support. Bring the the vehicle to your SUZUKI dealer to have port” in the “OPERATING YOUR VEHICLE” vehicle to your SUZUKI dealer to have the the problem corrected.
Page 131 Bring the vehicle to your SUZUKI dealer to have the problem corrected. For details, refer to “Dual camera brake sup- port”...
Page 132 If this light comes on, there is a problem with the LED headlight. Park the vehicle in a safe place and consult your SUZUKI dealer to have the problem corrected. 64J045 This indicator light comes on while the position lights, tail light and/or the head- lights are on.
Page 133 MAINTENANCE” section. filter change according to the maintenance Have your vehicle inspected by your schedule. SUZUKI dealer. This light comes on for several seconds when the ignition switch is turned to “ON” position or the engine switch is pressed to change the ignition mode to ON so you can check that light is working.
Page 134 (engine auto stop start system)” in the You should have the system inspected by “OPERATING YOUR VEHICLE” section. an authorized SUZUKI dealer. For details, refer to “ENG A-STOP system (engine auto stop start system)” in the “OPERATING YOUR VEHICLE” section.
Page 135 BEFORE DRIVING Depress brake pedal indicator Cruise indicator light (if equipped) Master warning indicator light (if equipped) (if equipped) 81P40090 76MH0A047 80P0382 When the cruise control system is on, this light will be on. Refer to “Auto Gear Shift” in the “OPERAT- When the ignition switch is turned to “ON”...
Page 136: Lighting Control Lever
BEFORE DRIVING Dual camera brake support warning Lighting operation Lighting control lever light (if equipped) EXAMPLE 80P0382 When the ignition switch is turned to “ON” position, this light comes on briefly so you can check that the light is working. If the function of the stereo camera stops temporarily or failure, this light will blink 75RM149...
Page 137 BEFORE DRIVING This system is operated by the signal from Auto-on headlight system the light sensor (1) on the passenger’s EXAMPLE (if equipped) side of the instrument panel. Do not cover the sensor (1). If you do, the system will not work correctly.
Page 138 BEFORE DRIVING NOTE: Light reminder buzzer Guide me light (if equipped) • When the “To home” is functioning, the front fog lights, rear fog lights and the The interior buzzer continuously beeps if To home function headlights (high beam) are not turned you open the driver’s door without turning This function turns on the front position off the headlights and position lights.
Page 139 BEFORE DRIVING NOTE: Front fog light switch (if equipped) Rear fog light switch (if equipped) • When the “To car” is functioning, the front fog lights, rear fog lights and the headlights (high beam) are not turned EXAMPLE EXAMPLE • Lighting time of the “To car” function can be changed on the information display.
Page 140 BEFORE DRIVING The headlight pattern must be adjusted to Left hand drive vehicle Adjusting headlight pattern avoid dazzling oncoming motorists and To readjust the light pattern by masking the can be set for right or left hand traffic. headlight lens; Headlight pattern, left hand traffic 1) Copy the A and B templates as shown LED headlights (if equipped)
Page 141 BEFORE DRIVING Right hand (A) Right hand drive vehicle Right hand (A) To readjust the light pattern by masking the headlight lens; 1) Copy the A and B templates as shown in the below illustrations. 2) Transfer the template to a self-adhesive waterproof material and cut it out.
Page 142 BEFORE DRIVING Templates for halogen headlights 75RM323 2-121 75RM0-01E...
Page 143: Headlight Leveling Switch
BEFORE DRIVING Headlight leveling switch Turn signal control lever Switch Position (if equipped) Vehicle Load Condition Driver only Driver + 1 passenger (in front seat) Driver + 3 or 4 passengers, no cargo Driver + 57L21128 3 or 4 passengers, 75RM008 cargo added WARNING...
Page 144 With the ignition switch in “ON” position or its indicator (1 to 4 times). Please ask an the ignition mode ON, move the lever authorized SUZUKI dealer for the customi- upward or downward to activate the right zation. or left turn signals.
Page 145: Hazard Warning Switch
If you cannot use the wipers after a while, ard when you park your vehicle in case of there may be another problem. Ask your emergency. SUZUKI dealer to have the wipers inspected. 2-124 75RM0-01E...
Page 146 BEFORE DRIVING Windshield wipers Windshield washer EXAMPLE EXAMPLE EXAMPLE 68PM00238 If the lever is equipped with “INT TIME” control, turn the control forward or back- 68PM00237 68PM00239 ward to adjust the intermittent wiper opera- To turn the windshield wipers on, move the To spray windshield washer fluid, pull the tion to the desired interval.
Page 147 BEFORE DRIVING Rear window wiper/washer switch NOTICE NOTICE To help prevent damage to the wind- Clear ice or snow from the rear win- EXAMPLE shield wiper and washer system dow and rear wiper blade before components, you should take the fol- using the rear wiper.
Page 148: Tilt Steering Lock Lever
BEFORE DRIVING Tilt steering lock lever Horn WARNING Never attempt to adjust the steering wheel while the vehicle is moving or EXAMPLE EXAMPLE you could lose control of the vehicle. 75RM044 75RM045 (1) LOCK Press the horn button of the steering wheel (2) UNLOCK to sound the horn.
Page 149 BEFORE DRIVING Type 2 If the outside rearview mirror has the mark Heated rear window switch / (2), it is also equipped with the heated out- EXAMPLE side rearview mirrors. When you push the heated outside rearview switch (1), both the heated outside rear- mirror switch (if equipped) view mirrors and the heated rear window will operate simultaneously.
Page 150 BEFORE DRIVING MEMO 2-129 75RM0-01E...
Page 151 OPERATING YOUR VEHICLE OPERATING YOUR VEHICLE Exhaust gas warning ............3-1 Daily inspection checklist ..........3-1 Engine oil consumption ............. 3-2 Ignition switch (vehicle without keyless push start system) ....3-3 Engine switch (vehicle with keyless push start system) ......3-5 Keyless push start system (if equipped) ......
Page 152: Exhaust Gas Warning
OPERATING YOUR VEHICLE Exhaust gas warning Daily inspection checklist WARNING (Continued) • Do not park with the engine run- Before driving ning for a long period of time, even in an open area. If it is necessary to sit for a short time in a parked vehi- cle with the engine running, check that the air intake selector is set to FRESH AIR and the blower is at...
Page 153: Engine Oil Consumption
OPERATING YOUR VEHICLE NOTE: the hood all the way without releasing Engine oil consumption It is normal for water to drip from the air the secondary latch. Close the hood conditioning system after use. securely after checking for proper latch It is normal for the engine to consume operation.
Page 154 OPERATING YOUR VEHICLE making it appear that the oil level has not Ignition switch (vehicle without changed. EXAMPLE You should also be aware that the diluting keyless push start system) ingredients evaporate out when the vehicle is subsequently driven at high speeds, such as on an expressway, making it appear that oil is excessively consumed after high-speed driving.
Page 155 OPERATING YOUR VEHICLE Manual transaxle/Auto Gear Shift Accessories such as the radio can oper- Turn to “LOCK” ate, but the engine is off. This is the normal operating position. All electrical systems are on. Push START This is the position for starting the engine using the starter motor.
Page 156 SUZUKI dealer. Auto Gear Shift – Provided you have the Press the engine switch to select this igni- • Do not leave the ignition switch in keyless push start system remote control- tion mode to use such electric equipment “ON”...
Page 157: Keyless Push Start System
OPERATING YOUR VEHICLE CVT – Provided you have the keyless Unreleased steering lock warning Keyless push start system push start system remote controller with you, the engine automatically starts when If the steering lock remains engaged when (if equipped) you press the engine switch to select this you press the engine switch to change the ignition mode after placing the gearshift ignition mode to ON, the information dis-...
Page 158 OPERATING YOUR VEHICLE Every time you press the engine switch, Engine switch illumination Selection of ignition modes the ignition mode changes as follows. The engine switch is illuminated (lit) in the Press the engine switch to select ACC or Manual transaxle or Auto Gear Shift following situations: ON mode as follows when you use an •...
Page 159 Contact in “P” position the ignition mode cannot an authorized SUZUKI dealer for an be returned to LOCK (OFF). inspection of the system. • When selecting the ignition modes, the •...
Page 160 OPERATING YOUR VEHICLE by pressing the engine switch and then REMOTE CONTROLLER OUTSIDE perform the engine starting operation. warning Refer to “Starting engine (vehicle with key- less push start system)” in this section. When either of the conditions described • Always keep the remote controller with below is met, the system issues a you as the driver.
Page 161: Parking Brake Lever
TROLLER OUTSIDE warning may not the seats. To set the parking brake, hold rized SUZUKI dealer. be given at that time. the brake pedal down and pull the parking – The remote controller is outside the brake lever all the way up.
Page 162 OPERATING YOUR VEHICLE Parking brake reminder buzzer WARNING WARNING A buzzer sounds intermittently to remind Always set the parking brake fully When parking vehicle you to release the parking brake if you before leaving your vehicle or it may extremely cold weather, the following start the vehicle without releasing the park- move, causing injury or damage.
Page 163 Depressing the accelerator pedal increases power output and speed. Brake pedal (2) 80J2121 Your SUZUKI vehicle is equipped with front Auto Gear Shift or CVT disc brakes and rear drum brakes. Depressing a brake pedal applies both EXAMPLE sets of brakes.
Page 164: Start System
OPERATING YOUR VEHICLE 1) Check that the parking brake is set fully. Starting a cold and warm engine Starting engine 2) Manual transaxle – Shift into “N” (Neu- tral) and depress the clutch pedal all (vehicle without keyless push With your foot taken off the accelerator the way to the floor.
Page 165 OPERATING YOUR VEHICLE 1) Check that the parking brake is set fully. Starting engine WARNING 2) Manual transaxle – Shift to “N” (Neutral) and fully depress the clutch pedal. Hold (vehicle with keyless push Check that the parking brake is set the clutch and brake pedals fully fully and the transaxle is in Neutral start system)
Page 166 If you are unable to start the engine using raced before stopping, a clicking sound this procedure, consult your SUZUKI may be heard from around the engine dealer. when it is restarted. This is not a mal- function.
Page 167 Contact your SUZUKI dealer for inspection. • The immobilizer/keyless push start sys- tem warning light will come on for about 5 seconds while the master warning indi- cator light is blinking.
Page 168 LOCK (OFF) using the engine switch and this happens, have the vehicle inspected then lock the doors. Without returning the EXAMPLE by an authorized SUZUKI dealer after ignition mode to LOCK (OFF), you cannot doing the following: use a request switch or keyless push start 75RM254 •...
Page 169 OPERATING YOUR VEHICLE Shifting NOTICE NOTICE All forward gears are synchronized and provide quiet and easy shifting. Always Do not downshift to a lower gear at • To help avoid clutch damage, do depress the clutch pedal all the way to the the speed faster than the maximum not use the clutch pedal as a foot- floor before shifting gears.
Page 170 OPERATING YOUR VEHICLE Models with switch of S-mode The gearshift lever has a lock mechanism Continuously variable transaxle to help prevent accidental shifting. To shift (CVT) EXAMPLE the gearshift lever: Gearshift lever Models with manual mode Models with manual mode EXAMPLE EXAMPLE 75RM049...
Page 171 OPERATING YOUR VEHICLE Models with switch of S-mode NOTE: NOTICE • Always shift the gearshift lever without EXAMPLE pushing in the knob button (1) except Do not shift the gearshift lever into when you shift from “P” to “R”, from “D” “R”...
Page 172 OPERATING YOUR VEHICLE L (Low) (models with switch of S-mode) Switch of S-mode (models with switch Switch of S-mode is OFF Use this position to provide maximum of S-mode) This mode is suitable for normal driving. power when climbing steep hills or driving •...
Page 173 OPERATING YOUR VEHICLE Manual mode (models with manual The information display shows the manual NOTE: mode) mode indicator (1) and the current gear When you change gear, sometimes the The CVT can shift gears automatically. position (2). transaxle may not shift to the desired gear When using the manual mode, you can but a buzzer sounds instead.
Page 174 OPERATING YOUR VEHICLE Temporary manual mode If you cannot shift CVT gearshift Pull the shift paddle toward you when driv- lever out of “P” (PARK) ing with the gearshift lever in the “D” posi- tion. The information display shows the Left Hand Drive Vehicle manual mode indicator (1) and the current gear position (2).
Page 175 OPERATING YOUR VEHICLE 1) Be sure the parking brake is firmly Right Hand Drive Vehicle 1) Be sure the parking brake is firmly applied. applied. 2) If the engine is running, stop the 2) If the engine is running, stop the engine.
Page 176 OPERATING YOUR VEHICLE The features are as follows: Depress brake pedal indicator Auto Gear Shift Auto Gear Shift is a 5-speed forward/ reverse transaxle. Auto Gear Shift has the basic features of conventional manual transaxle, but clutch operation and transaxle gear shifting are controlled electronically.
Page 177 OPERATING YOUR VEHICLE Starting the engine Creeping function Drive (D) mode When starting the engine, always place the This vehicle has a creeping function that When the Drive (D) mode is activated, the gearshift lever in the “N” position and helps the vehicle to start smoothly by most appropriate gear position is automati- depress the brake pedal firmly.
Page 178 “N” position automatically when the vehicle speed becomes less than 10 km/h (6 mph), there may be a sys- tematic malfunction. In this case, ask your SUZUKI dealer to inspect the Auto Gear Shift system as soon as possible. 3-27...
Page 179 OPERATING YOUR VEHICLE Downhill Manual (M) mode Downshifting 1) Depress the brake pedal and shift the The gears are not shifted automatically. To gearshift lever to the “D” position. Make shift the transaxle, the driver must operate sure that the gear is in 1st by checking the gearshift lever to the “+”...
Page 180 In this case, ask your by checking the gear position indicator, upshifting, downshifting or braking SUZUKI dealer to inspect the Auto then depress the accelerator pedal. on a slippery surface. Sudden Gear Shift system as soon as pos-...
Page 181 OPERATING YOUR VEHICLE 3) Release the parking brake and brake Starting off on an uphill/downhill slope: Backing up pedal. Depress the accelerator pedal After the vehicle has stopped completely, Uphill slowly for smooth starting. depress the brake pedal and shift the gear- 1) Apply the parking brake firmly so that shift lever to the “R”...
Page 182 OPERATING YOUR VEHICLE • The system will not allow shifting to the Stopping WARNING “R” position if the vehicle speed is over The vehicle can be stopped by depressing about 3 km/h (2 mph). If the gearshift the brake pedal regardless of the gear (Continued) lever is operated under this condition, position.
Page 183 3) Stop the engine. side of the road and stop the engine, • On a downhill slope, the gear and then ask your SUZUKI dealer to NOTE: should be put in reverse, and in 1st inspect your vehicle. Otherwise, the •...
Page 184 OPERATING YOUR VEHICLE “N” indicator blinking Manual transaxle vehicle Gearshift indicator (if equipped) When the gear indicator lamp blinks “N”, If UP/DOWN arrow is indicated on the dis- you should depress the brake pedal and play while driving, we recommend you to shift the gearshift lever to “N”...
Page 185 OPERATING YOUR VEHICLE NOTE: Example of the gearshift indicator • For manual transaxle vehicle, the gear- Manual transaxle shift indicator is not indicated when the gear position is in “N” (Neutral). Indication Description • For manual transaxle vehicle, if you depress the clutch pedal while UP/ Lower gear position is selected for the vehicle speed and/ DOWN arrow is indicated, the indication...
Page 186 OPERATING YOUR VEHICLE NOTE: ENG A-STOP system CAUTION If your vehicle is equipped with the auto- matic heating and air conditioning system, (engine auto stop start system) • Do not get out of the vehicle when you can change the automatic engine stop the engine has been stopped auto- (if equipped) condition via the information display.
Page 187 OPERATING YOUR VEHICLE ating conditions of ENG A-STOP sys- Automatically stopping/restarting NOTICE tem”. of the engine • During the automatic engine stop, the Since models equipped with this sys- engine may shut down, accompanied tem use a lead-acid battery specifi- Manual transaxle vehicles by an interior buzzer or restarted, to cally for the high-efficiency ENG A-...
Page 188 OPERATING YOUR VEHICLE • The audio and other electrical compo- While engine auto stopping, CVT vehicles nent can be used during the automatic depressing the clutch pedal will restart the 1) While driving, the ENG A-STOP indica- engine stop, but the air conditioner will engine consuming fuel.
Page 189 OPERATING YOUR VEHICLE 2) Depress the brake pedal to decelerate NOTE: while the gearshift lever is in the “D” • The engine is not stopped automatically position will automatically stop the when decelerating without depressing engine before the vehicle is stopped the brake pedal, for example, by using (approximately 13 km/h or less).
Page 190 OPERATING YOUR VEHICLE Precautions of when the engine is stopped automatically WARNING Do not perform any of the following operations while the engine has been stopped automatically. This may result in an acci- dent. Operation/Vehicle Condition Solution Engine hood opened To restart the engine, follow the procedure below.
Page 191 OPERATING YOUR VEHICLE NOTE: The following indicator lights in the instrument cluster do not come on when the engine is stopped automatically. • Malfunction indicator light, electric power steering light, oil pressure light, charging light 3-40 75RM0-01E...
Page 192 OPERATING YOUR VEHICLE Operating conditions of ENG A-STOP system Standby conditions If all of the following conditions are met while driving, the automatic engine stop will be permitted. • For CVT, the ENG A-STOP indicator light (green) will come on. When the engine is started •...
Page 193 OPERATING YOUR VEHICLE Conditions to stop the engine automatically If all of the following conditions are met while the standby conditions are met, the engine is stopped automatically when the vehicle is decelerating before stopping or when the vehicle is stopped. ®...
Page 194 OPERATING YOUR VEHICLE Conditions to restart the engine automatically If any of the following vehicle conditions occur or operations are performed while the engine is stopped automatically, the engine is restarted automatically and the ENG A-STOP indicator light (green) goes off. •...
Page 195 OPERATING YOUR VEHICLE #1: After the ENG A-STOP indicator light (green) blinks, it goes off. Also, the interior buzzer may sound at the same time. #2: Depending on the situations of malfunction, it is a normal restart or the restart as #1. #3: The engine may be restarted automatically when the brake pedal is depressed lightly.
Page 196 If it blinks, have • Each time the engine is stopped manu- the vehicle serviced by an authorized ally, the system is activated, and the SUZUKI dealer. ENG A-STOP OFF indicator light goes – If the system is operating normally off.
Page 197 Stored power is being used by electrical The SHVS (Smart Hybrid Vehicle by the ISG is functioning. components, such as the audio system, Suzuki) of this vehicle is a system that without the batteries being charged. uses generators with motor function (ISG) • Normal driving conditions: to operate the following functions accord- The ISG is not functioning.
Page 198 OPERATING YOUR VEHICLE • The motor assistance function is func- • The lithium-ion battery is charged more Deceleration energy regenerating indi- tioning during moderate accelerating: than a certain amount, and the tempera- cator light The ISG assists the engine. ture inside the battery is within the speci- fied range.
Page 199 OPERATING YOUR VEHICLE Eco-Cool (if equipped) I/S AC Settings (if equipped) Cruise control (if equipped) When driving while using the air condi- • When using the automatic heating and The cruise control system allows you to tioner, cold air is stored in the cooling stor- air conditioning system (if equipped), maintain a steady speed without keeping age medium of the air conditioner unit.
Page 200 OPERATING YOUR VEHICLE Instrument cluster with tachometer Setting cruising speed 1) Turn on the cruise control system by pushing cruise switch (1). When the cruise indicator (4) (for instrument clus- ter with tachometer) or cruise indicator light (6) (for instrument cluster without tachometer) comes on, you can set 75RM115 cruising speed.
Page 201 OPERATING YOUR VEHICLE Be careful of the following when operat- Changing speed temporarily Changing cruising speed ing with the cruise control Even if your vehicle is equipped with the When the cruising speed is maintained, Using the accelerator pedal dual camera brake support, it cannot auto- you can temporarily accelerate or deceler- To reset at a faster cruising speed, accel- matically adjust to the speed of the vehicle...
Page 202 OPERATING YOUR VEHICLE NOTE: To turn off the cruise control system, push Speed limiter (if equipped) You can adjust the set speed by approxi- cruise switch (1) and check that the cruise mately 1.5 km/h (0.9 mph) by pushing indicator (4) or cruise indicator light (6) is “RES +/SET –”...
Page 203 OPERATING YOUR VEHICLE Setting maximum speed Exceeding maximum speed Changing speed setting 1) Turn on the speed limiter system by You can exceed the maximum speed tem- Setting to the current speed pushing “LIMIT” switch (1). When the porarily by quickly depressing the acceler- 1) Push “CANCEL”...
Page 204 OPERATING YOUR VEHICLE NOTE: Canceling speed limiter Dual camera brake support • While the system is working, if a vehicle in front of you moves outside of the ste- • To cancel the speed limiter, push “CAN- (if equipped) reo camera’s detection field or the vehi- CEL”...
Page 205 OPERATING YOUR VEHICLE Frontal collision warning When there is a risk of a frontal crash, a warning will be given through the information dis- play and sound. EXAMPLE Information display without with tachometer buzzer tachometer 75RM282 Warning brake system If the driver cannot take or is insufficient to take evasive action such as brake operation and steering operation after frontal collision warning activates, the system applies brake lightly.
Page 206 OPERATING YOUR VEHICLE Brake assist system When there is high probability of a frontal crash, the brake assist system provides more powerful braking when you slam down on the brake pedal. Brake assist system might work at the same time as the warning brake system or automatic brake system. EXAMPLE Information display without...
Page 207 OPERATING YOUR VEHICLE Situations where the system does Situations where the vehicle may Situations where the system may not activate not decelerate properly activate by chance Under the following situations, the system Under the following situations, the vehicle Under the following situations, the stereo does not activate.
Page 208 OPERATING YOUR VEHICLE Frontal collision warning Warning brake system EXAMPLE When you are operating at a speed of When you are operating at speeds approximately 5 km/h (3 mph) or over and between approximately 5 km/h to 120 km/h there is a risk of a frontal crash, a warning (3 mph to 75 mph) and if the driver cannot will work.
Page 209 OPERATING YOUR VEHICLE NOTE: Brake assist system Automatic brake system The indication on the information display and the dual camera brake support indica- When you are operating at speeds When a frontal crash is judged to be tor light will go off after 3 seconds from between approximately 10 km/h to 120 km/ unavoidable at a speed of approximately being released the automatic brake sys-...
Page 210 OPERATING YOUR VEHICLE Situations where the system may not Lane departure warning WARNING activate properly Under the following situations, the system When you are operating at a speed of • The lane departure warning may may not activate. approximately 60 km/h (37 mph) or over not be suitable for every situation.
Page 211 OPERATING YOUR VEHICLE Situations where the system may acti- Vehicle swaying warning WARNING vate by chance Under the following situations, the system When you are operating at a speed of • The vehicle swaying warning may may activate. approximately 60 km/h (37 mph) or over not be suitable for every situation.
Page 212 OPERATING YOUR VEHICLE Situations where the system may not – When tires are not inflated to the rec- Dual camera brake support OFF activate properly ommended tire inflation pressure switch Under the following situations, the system – With worn tires equipped may not activate.
Page 213 OPERATING YOUR VEHICLE • When you want to turn off the system, Lane departure warning OFF switch WARNING push and hold the dual camera brake support OFF switch (1) until the interior You can turn off the lane departure warning If you attempt to press the lane buzzer beeps and the dual camera and the vehicle swaying warning.
Page 214 62R0114 occur. dual camera brake support, and (1) Stereo camera – Do not touch the lens of the ste- ask your SUZUKI dealer to have reo camera. them inspected. – Do not clean the lens of the ste- (Continued) reo camera by yourself.
Page 215 Observe the following instructions. If • Do not apply any accessories the lens of the stereo camera gets (other than SUZUKI genuine acces- dirty, it may need to be replaced. sories), films or stickers to the area • Do not touch the lens of the stereo listed below.
Page 216 OPERATING YOUR VEHICLE Temporary stop or failure of the stereo camera The following chart shows the temporary stop or failure of the stereo camera. Stereo camera (1) Dual camera brake support indicator light Temporary Stop Failure (2) Lane departure warning indicator light (3) Indication of information display (with tachometer) (4) Master warning indicator light...
Page 217 • If both of the indicators stay on after – When the automatic brake system has restarting the engine, there may be a been operating for long periods failure of the stereo camera. Ask your SUZUKI dealer to have the stereo cam- era inspected. 3-66 75RM0-01E...
Page 218 • While using the windshield washer be detected by the stereo camera. Also, the function of the stereo camera • When a wiper blade other than SUZUKI In the following situations, there may may stop temporarily. When the situations genuine parts, including short type wiper...
Page 219 OPERATING YOUR VEHICLE When the following types of vehicles or • There is another obstacle beside a vehi- obstacles are in front of you, or when the EXAMPLE following situations occur, the stereo cam- • A fence, wall or shutter which having no era may not detect obstacles in front of you patterns or uniform patterns such as or may need more time to detect obsta-...
Page 220 OPERATING YOUR VEHICLE • When the vehicle in front of you turns, accelerates or decelerates suddenly • An object outside of the irradiation range of the headlights • An object which jumps out in front of you • When change lane approach the preceding vehicle When the following types of partition lines...
Page 221 There may be a problem with the stereo buzzer) camera. If the message does not disappear after restarting the engine, have your vehicle inspected by an authorized SUZUKI dealer. 75RM239 Blinks Continuous beep (from inte- The vehicle swaying warning is working.
Page 222 OPERATING YOUR VEHICLE Emergency stop signal (ESS) (if equipped) WARNING Although the ESS is designed to ESS stands for Emergency Stop Signal. reduce number rear-end crashes that occur from sudden brak- ESS is a feature that gives a warning to a following vehicle by flashing all turn signal lights ing, by warning a following vehicle, it faster than usual if all the following conditions are met.
Page 223 OPERATING YOUR VEHICLE Rearview camera location Rearview camera (if equipped) NOTICE If you use the rearview camera for a When the gearshift lever is shifted to “R” long time when the ignition switch is position while the ignition switch is in “ON” in “ON”...
Page 224 OPERATING YOUR VEHICLE Display range of rearview camera How to use rearview camera NOTICE 1) Turn the ignition switch to “ON” position EXAMPLE If water enters the rearview camera, it or press the engine switch to change may cause a malfunction or catch the ignition mode to ON.
Page 225 OPERATING YOUR VEHICLE NOTE: Uphill incline behind the vehicle Downhill incline behind the vehicle • Images shown on the display from the rearview camera are reversed images EXAMPLE EXAMPLE (mirror images). • The colors of objects on the rearview camera may differ from the actual object colors.
Page 226 60 km/h (37 mph) will be can bring the vehicle to a complete stop by rized SUZUKI dealer as soon as possible. approximately 4 times greater than the pressing the brake pedal once and holding braking distance needed at 30 km/h (19 it down.
Page 227 OPERATING YOUR VEHICLE Anti-lock brake system (ABS) WARNING WARNING ABS will help you avoid skidding by elec- Even without reserve power in the • On some types of loose surfaces tronically controlling braking pressure. It brake system, you can still stop the (such as gravel, snow-covered will also help you maintain steering control vehicle by pressing the brake pedal...
Page 228 ABS system. skidding situation, computer will Ask your SUZUKI dealer to inspect change braking pressure several times the ABS system immediately. If the each second to prevent the wheels from ABS system becomes inoperative, locking. When you start your vehicle or...
Page 229: Electronic Stability Program
OPERATING YOUR VEHICLE ® The ESP has the following three sys- Anti-lock brake system (ABS) Electronic stability program tems: ® (ESP ) (if equipped) ABS will help you avoid skidding by elec- tronically controlling braking pressure. It Stability control system will also help you maintain steering control ®...
Page 230 ESP sys- begins to move. This means that the tems (other than ABS). You should above systems are in the self-check have the systems inspected by an mode. This sound does not indicate a authorized SUZUKI dealer. malfunction. 3-79 75RM0-01E...
Page 231 ® there may be a problem with the ESP WARNING system. Have your vehicle inspected by an Do not rely excessively on the hill authorized SUZUKI dealer. descent control system. The hill 75RM055 descent control system may not con- NOTE: ®...
Page 232 OPERATING YOUR VEHICLE Hill descent control switch When the vehicle speed exceeds about 7 WARNING km/h (4 mph) without depressing the accelerator pedal, the hill descent control (Continued) system applies the brakes automatically to • The hill descent control system maintain the vehicle speed at about 7 km/h may be activated when the gear- (4 mph).
Page 233 Have your vehicle tem. Have your vehicle inspected by an ing conditions are fulfilled, the hill descent inspected by an authorized SUZUKI authorized SUZUKI dealer. control indicator comes on. If the hill dealer. • The hill descent control indicator does...
Page 234 OPERATING YOUR VEHICLE Grip control switch Grip control system (if equipped) CAUTION When one side of the tires is slipping on (Continued) slippery road surfaces such as a snow-cov- – Do not modify the vehicle’s sus- ered road and it is difficult to start the vehi- pension or brake (Altering the cle, the grip control system controls the vehicle height, etc.).
Page 235 OPERATING YOUR VEHICLE How grip control system works Hill hold control system (if equipped) WARNING When the grip control switch is on and one side of the tires is slipping, the grip control The hill hold control system is designed to (Continued) system assists you in smooth starting by assist you in starting to move up hills.
Page 236: Tire Pressure Monitoring
SUZUKI dealer. Driving on a significantly under-inflated tire causes the tire to overheat and can lead to NOTE: tire failure. Under-inflation also reduces...
Page 237 Check and adjust your tire inflation tires can result in loss of control or by an authorized SUZUKI dealer. pressure at least once a month. Refer an accident. Even if the light turns off after blink- to “Tires”...
Page 238 SUZUKI dealer. braking. Be aware that driving on a tire. significantly under-inflated tire can •...
Page 239 OPERATING YOUR VEHICLE after driving, they are warm. Even if the TPMS malfunction indicator tire pressure seems to be good in this condition, it could fall below the specified Your vehicle has also been equipped with pressure when tires cool down. Also, if a TPMS malfunction indicator to indicate tires are inflated to the specified pres- when the system is not operating properly.
Page 240 TPMS sensors or tire chains SUZUKI dealer. are used. • When you use non-genuine SUZUKI wheels or tires. • When the pressure of any tire is too high. • When there is a problem with the receiver of the TPMS controller.
Page 241 OPERATING YOUR VEHICLE To check the current tire inflation pres- TPMS setting sure (instrument cluster with tachometer) EXAMPLE • For the instrument cluster with tachome- ter, you can check the current tire infla- EXAMPLE tion pressure on the information display. •...
Page 242 OPERATING YOUR VEHICLE NOTE: To set the initial value of tire pressure • If the low tire pressure warning light (instrument cluster with tachometer) EXAMPLE comes on, the information display will be NOTE: switched to “Tyre Press” display and the For the instrument cluster without tachom- corresponding tire pressure indication eter, refer to “Setting mode”...
Page 243 OPERATING YOUR VEHICLE EXAMPLE EXAMPLE EXAMPLE 75RM321 75RM332 75RM334 2) Push the brightness control switch (2) 3) Push the brightness control switch (2) 4) Push the brightness control switch (2) up or down to select “TPMS” and push up or down to select “TPMS Mode” and up or down to select the initial value the information switch (1).
Page 244 TPMS operation. WARNING Use of tires or wheels not recom- mended by SUZUKI can result in fail- ure of the TPMS. When replacing tires and wheels, use only tires and wheels recommended by SUZUKI as standard or optional equipment for your vehicle.
Page 245 DRIVING TIPS DRIVING TIPS Running-in ................4-1 Catalytic converter .............. 4-1 Improving fuel economy ............. 4-2 Highway driving ..............4-3 Driving on hills ..............4-3 Driving on slippery roads ........... 4-4 60G409 75RM0-01E...
Page 246: Catalytic Converter
DRIVING TIPS Running-in Catalytic converter NOTICE The future performance and reliabil- ity of the engine depends on the care 52D078S and restraint exercised during its early life. It is especially important to observe the following precautions WARNING during the first 960 km (600 miles) of •...
Page 247: Improving Fuel Economy
DRIVING TIPS heat damage to the catalytic converter and Improving fuel economy other vehicle components. NOTICE The following instructions will help you improve fuel economy. To minimize the possibility of cata- Avoid excessive idling lytic converter or other vehicle dam- If you are to wait for more than a minute age: while you are parked, stop the engine and...
Page 248: Highway Driving
DRIVING TIPS Keep the air cleaner clean Highway driving Driving on hills EXAMPLE When driving at highway speeds, pay Manual transaxle attention to the following: • Stopping distance progressively increases with vehicle speed. Apply the brakes far enough ahead of the stopping point to allow for the extra stopping dis- tance.
Page 249 DRIVING TIPS Driving on slippery roads NOTICE When descending a downhill, Never turn the ignition key to “LOCK” posi- tion or press the engine switch to change the ignition mode to LOCK (OFF). Emission control system and CVT (if equipped) damage may result. 75RM296 •...
Page 250 Tire chains Stuck vehicle minutes of rocking, we recommend you to consult your SUZUKI dealer or a road- Tire chains should only be used if they are If your vehicle gets stuck in snow, mud or side assistance service. If a towing ser-...
Page 251 DRIVING TIPS WARNING (Continued) • Do not use tires other than those specified by SUZUKI. Never use dif- ferent sizes or types of tires on the front and rear wheels. For informa- tion regarding the specified tires, refer to the tire information label located on the driver’s door lock...
Page 252 DRIVING TIPS MEMO 75RM0-01E...
Page 253 OTHER CONTROLS AND EQUIPMENT OTHER CONTROLS AND EQUIPMENT Fuel filler cap ............... 5-1 Engine hood ................ 5-2 Sun visor ................5-4 Interior light ................. 5-5 Accessory socket ..............5-6 AUX/USB socket (if equipped) ........... 5-7 Assist grips (if equipped) ........... 5-7 Glove box ................
Page 254: Fuel Filler Cap
OTHER CONTROLS AND EQUIPMENT A fuel filler cap is located on the left rear Fuel filler cap side of the vehicle. The fuel filler door can EXAMPLE be unlocked by pulling up the opener lever located on the outboard side of the driver’s seat and locked by simply closing the door.
Page 255: Engine Hood
WARNING If you need to replace the fuel cap, 75RM132 use a genuine SUZUKI cap. Use of an 2) Push the under-hood release lever improper cap can result in a malfunc- sideways with your finger, as shown in...
Page 256 OTHER CONTROLS AND EQUIPMENT To close the engine hood: CAUTION 1) Lift the hood up slightly and remove the EXAMPLE prop rod from the hole. Put the prop rod To avoid injury, check that no part of back into the holding clip. the occupant’s body such as hands or head is in the path of the hood EXAMPLE...
Page 257: Sun Visor
OTHER CONTROLS AND EQUIPMENT Card holder (if equipped) Vanity mirror (if equipped) Sun visor EXAMPLE EXAMPLE 80JM152 75RM134 (1) Mirror cover (3) Vanity mirror (2) Card holder 79J161 To use the vanity mirror (3) on the back of The sun visors can be pulled down to block You can put a card in the card holder (2) on the sun visor, pull up the mirror cover (1).
Page 258: Interior Light
OTHER CONTROLS AND EQUIPMENT DOOR (2) Luggage compartment (if equipped) Interior light • The light comes on while any of the doors (including the tailgate) is opened. For about 15 seconds after all doors are Front closed, the light will remain on and then fade out.
Page 259: Accessory Socket
OTHER CONTROLS AND EQUIPMENT The accessory socket will work when the Accessory socket NOTICE ignition switch is in “ACC” or “ON” position, or the ignition mode is ACC or ON. Do not leave the tailgate open with Center console Each socket can be used to provide luggage compartment light...
Page 260: Glove Box
OTHER CONTROLS AND EQUIPMENT AUX/USB socket (if equipped) Assist grips (if equipped) Glove box EXAMPLE 75RM170 54G249 75RM137 Connect your portable digital music player, Assist grips are provided for convenience. To open the glove box, pull the latch lever. etc. to this socket to enjoy music through To close it, push the lid until it latches the vehicle’s audio system.
Page 261 OTHER CONTROLS AND EQUIPMENT Cup holder and storage area EXAMPLE (2) (3) 75RM138 There is a recess in the glove box. WARNING Never drive with the glove box lid open. It could cause injury if an acci- dent occurs. 75RM297 (1) Center console tray (2) Front cup holders (3) Front bottle holder...
Page 262 OTHER CONTROLS AND EQUIPMENT Center console tray (1) Front cup holders (2) / Front bottle holder (3) / Rear cup holder (5) Rear bottle holder (6) WARNING Use the rear cup holder to put a cup with a You should only place a bottle with a cap in lid or a bottle with a cap.
Page 263: Floor Mats
When you replace the floor mats in your vehicle with a different type such as all- weather floor mats, we highly recommend to use genuine SUZUKI floor mats for proper fitting. 5-10 75RM0-01E...
Page 264: Luggage Compartment Cover
Luggage or other cargo placed in the lug- items such as wood panels and surf- SUZUKI dealer. If you use a roof rack, gage compartment is hidden from view by boards, to both the front and rear of the observe the instructions and precautions in a luggage compartment cover.
Page 265: Frame Hooks
OTHER CONTROLS AND EQUIPMENT Front Frame hooks WARNING • Abrupt maneuvers or failure to Your SUZUKI does not recommend you EXAMPLE properly secure cargo can allow use the frame hooks for towing another the cargo to fly off the vehicle and vehicle.
Page 266 OTHER CONTROLS AND EQUIPMENT To install the hook (1), follow the procedure below. EXAMPLE EXAMPLE EXAMPLE 75RM015 75RM016 2) Remove the cover (C) by using a jack 3) Install the towing hook (1) by hand. 75RM014 handle (A) covered with a soft cloth as 1) Pick up the towing hook (1), jack handle shown in the illustration.
Page 267 OTHER CONTROLS AND EQUIPMENT Rear Other holes EXAMPLE EXAMPLE EXAMPLE 75RM017 4) To tighten the towing hook (1), turn it clockwise by using a wheel brace (B) 75RM018 75RM140 until the hook (1) is securely installed. The frame hook (2) is provided on the rear The frame holes (3) are provided only for of the vehicle for use in emergency situa- transporting by a car carrier trailer.
Page 268 OTHER CONTROLS AND EQUIPMENT Air outlet Heating and air conditioning system There are three types of heating and air conditioning systems as follows: • Heating system • Manual heating and air conditioning sys- • Automatic heating and air conditioning system (climate control) EXAMPLE 75RM351 1.
Page 269 OTHER CONTROLS AND EQUIPMENT Side outlet Center outlet 66RH123 Move the knob (1) horizontally or the case (2) vertically to adjust the direction of air- flow as desired. 75RM019 CAUTION When open, air comes out regardless of Prolonged exposure to hot air from the air flow selector position.
Page 270 OTHER CONTROLS AND EQUIPMENT Air flow selector (3) Heating system Description of controls 75RM022 This is used to select one of the following functions. VENTILATION (a) 75RM312 75RM352 Temperature selector (1) Temperature-controlled air comes out of This is used to select the temperature by turning the selector. the center and side air outlets.
Page 271 OTHER CONTROLS AND EQUIPMENT BI-LEVEL (b) HEAT & DEFROST (d) Air intake selector (4) 75RM353 75RM355 75RM059 Temperature-controlled air comes out of Temperature-controlled air comes out of This selector is used to select the following the floor outlets and cooler air comes out the floor outlets, the windshield defroster modes.
Page 272 OTHER CONTROLS AND EQUIPMENT Head cooled/Feet warmed heating System operating instructions Select BI-LEVEL and FRESH AIR, the EXAMPLE temperature selector to the desired tem- Natural ventilation perature position, and the blower speed Select VENTILATION and FRESH AIR, the selector to the desired blower speed posi- temperature selector to the desired tem- tion.
Page 273 OTHER CONTROLS AND EQUIPMENT Models with ENG A-STOP System (if equipped) • If the heating performance can no longer perform at a sufficient level due to auto- matically stopping the engine, press the ENG A-STOP OFF switch to deactivate the ENG A-STOP system. (The engine will automatically restart and the heating performance will be restored.) •...
Page 274: Manual Heating And Air Conditioning System
OTHER CONTROLS AND EQUIPMENT Air flow selector (3) Manual heating and air conditioning system Description of controls 75RM022 This is used to select one of the following functions. VENTILATION (a) 75RM060 75RM352 Temperature selector (1) Temperature-controlled air comes out of This is used to select the temperature by turning the selector.
Page 275 OTHER CONTROLS AND EQUIPMENT BI-LEVEL (b) HEAT & DEFROST (d) Air intake selector (4) 75RM353 75RM355 75RM059 Temperature-controlled air comes out of Temperature-controlled air comes out of This selector is used to select the following the floor outlets and cooler air comes out the floor outlets, the windshield defroster modes.
Page 276 OTHER CONTROLS AND EQUIPMENT Air conditioning switch (5) Head cooled/Feet warmed heating System operating instructions To turn on the air conditioning system, set Select BI-LEVEL and FRESH AIR, the the blower speed selector to a position temperature selector to the desired tem- Natural ventilation other than off and push in “A/C”...
Page 277 OTHER CONTROLS AND EQUIPMENT NOTE: Models with ENG A-STOP System • If you select RECIRCULATED AIR for an (if equipped) EXAMPLE extended period of time, the air in the • If the heating performance can no longer vehicle become contaminated. perform at a sufficient level due to auto- Therefore, should...
Page 278 OTHER CONTROLS AND EQUIPMENT (Except for vehicles using “HFO-1234yf” Maintenance refrigerant) NOTE: If you do not use the air conditioner for a Your vehicle uses the air conditioning long period, such as during winter, it may refrigerant HFC-134a, commonly called not give the best performance when you R-134a.
Page 279 OTHER CONTROLS AND EQUIPMENT Temperature selector (1) Automatic heating and air conditioning system (climate control) Description of controls 75RM026 Push the temperature selector (1) up or down to adjust the temperature. NOTE: If you push the temperature selector (1) until “HI” or “LO” appears on the display, the climate control system will operate at maximum heating or cooling.
Page 280 OTHER CONTROLS AND EQUIPMENT Blower speed selector (2) Air intake selector (3) RECIRCULATED AIR (a) When this mode is selected, outside air is shut off and inside air is recirculated. This mode is suitable when driving through an area with polluted air such as a tunnel, or when attempting to quickly cool down the vehicle.
Page 281 OTHER CONTROLS AND EQUIPMENT Air flow selector (4) VENTILATION (c) HEAT (e) 75RM352 75RM354 Temperature-controlled air comes out of Temperature-controlled air comes out of the center, side and rear air outlets. the floor outlets and the side outlets, a small amount of air comes out of the wind- BI-LEVEL (d) shield defroster outlets and also comes slightly out of the side defroster outlets.
Page 282 OTHER CONTROLS AND EQUIPMENT Defrost switch (5) Air conditioning switch (6) System operating instructions Automatic operation 75RM030 75RM031 Push the defrost switch (5) to turn on the The air conditioning switch (6) is used to defroster. turn on and off the air conditioning system only when the blower is on.
Page 283 “AUTO” switch (8). conditioning system. You should have the system inspected authorized EXAMPLE SUZUKI dealer. (10) NOTE: • To find the temperature at which you are 75RM357 most comfortable, start with the 22°C (72°F) or 25°C (75°F) setting. (the tem-...
Page 284 “INSPECTION AND MAINTENANCE” sec- refrigerants are available, including recy- position to defog the windows. tion. Have this job done by your SUZUKI cled R-12, but only R-134a should be used dealer as the lower glove box must be low- in your vehicle.
Page 285: Radio Antenna
75RM301 ence with your vehicle’s ignition Type B system, resulting in vehicle perfor- EXAMPLE mance problems. Consult your SUZUKI dealer or qualified service technician for advice. 61MM0A113 5-32 75RM0-01E...
Page 286 OTHER CONTROLS AND EQUIPMENT Audio system (Type A / Type B / Type C) (if equipped) EXAMPLE Type A Type B Type C 75RM080 ® Type A: AM/FM/DAB CD player with Bluetooth function ® Type B: AM/FM CD player with Bluetooth function ®...
Page 287 • Set the sound volume to a level unit, or lubricate the rotating parts. that will allow you to continue to Bring the unit to an authorized SUZUKI be aware of road and traffic condi- tions while driving. dealer.
Page 288 OTHER CONTROLS AND EQUIPMENT Removing the disc Proper way to hold the compact disc 52D347 52D348 To remove fingermarks and dust, use a Never stick labels on the surface of the soft cloth, and wipe in a straight line from compact disc or write on the surface with a the center of the compact disc to the cir- pencil or pen.
Page 289 OTHER CONTROLS AND EQUIPMENT 52D350 52D351 Do not use compact discs that have large Do not expose compact discs to direct sun- scratches, are misshaped, or cracked, etc. light or any heat source. Use of such discs will cause damage or prevent the system from operating prop- NOTE: erly.
Page 290 OTHER CONTROLS AND EQUIPMENT WARNING ® The Bluetooth word mark and logo are Access to http://www.ptc.panasonic.eu/, This is a class I laser product. Use registered trademarks and are owned by enter the below of controls or adjustments or perfor- the Bluetooth SIG, Ink. Model No.
Page 291 OTHER CONTROLS AND EQUIPMENT Information on disposal for users of waste electrical & electronic equip- ment (private households) This symbol on the products and/or accompanying documents means that used electrical and electronic products should not be mixed with general household waste. For proper treatment, recovery and recycling, please take these products to designated collection points, where they will be accepted on a free of charge basis.
Page 292 OTHER CONTROLS AND EQUIPMENT Part 15 of the FCC Rules WARNING FCC ID: ACJ932AZ1601 ® The Bluetooth word mark and logo are This is a class I laser product. Use of NOTE: registered trademarks and are owned by controls or adjustments or perfor- Properly shielded and grounded cables the Bluetooth SIG, Ink.
Page 293 OTHER CONTROLS AND EQUIPMENT ® Stop using this unit and a Bluetooth NOTE: ready device whenever requested. These limits are designed to provide rea- This unit shares the communication fre- sonable protection against harmful interfer- quency with other private or public wireless ence in a residential installation.
Page 294 OTHER CONTROLS AND EQUIPMENT Turning on/off power Basic operations Press “VOL PUSH PWR” knob (1) to turn on the power. The unit starts to operate in the previous setting that the power was EXAMPLE Type A turned off. Adjusting the volume Turn “VOL PUSH PWR”...
Page 295 OTHER CONTROLS AND EQUIPMENT Adjusting bass/treble/balance/fader Adjusting the AVC (Auto volume con- Preset-EQ 1) Press “TUNE/FLD PUSH SOUND” trol) Preset-EQ calls up various sound types in knob (2). The Auto Volume Control (AVC) function accordance with the listening music type. Each time the knob is pressed, sound automatically adjusts...
Page 296 OTHER CONTROLS AND EQUIPMENT Listening to the radio (Type A) Display EXAMPLE 68LM561 (1) “RADIO” button (2) UP button (3) DOWN button (4) “TUNE/FLD PUSH SOUND” knob (5) PRESET buttons ([1] to [6]) (6) “AS” button (A) Band (B) Frequency 75RM082 5-43 75RM0-01E...
Page 297 OTHER CONTROLS AND EQUIPMENT Selecting the reception band Preset memory Auto store mode on/off Press the “RADIO” button (1). 1) Select the desired station. Press “AS” button (6). Each time the button is pressed, the recep- 2) Hold down a desired button ([1] to [6]) Each time the button is pressed, the mode tion band will change as follows: of PRESET buttons (5) to which you...
Page 298 OTHER CONTROLS AND EQUIPMENT Display Listening to the radio (Type B / Type C) EXAMPLE Type B (1) “FM” button (2) “AM” button (3) UP button (4) DOWN button (5) “TUNE/FLD PUSH SOUND” knob (6) PRESET buttons ([1] to [6]) (7) “AS”...
Page 299 OTHER CONTROLS AND EQUIPMENT Selecting the FM band Auto store Radio reception Press “FM” button (1). Hold down “AS” button (7) for 2 seconds or Radio reception can be affected by envi- Each time the button is pressed, the recep- longer.
Page 300 OTHER CONTROLS AND EQUIPMENT Using the RDS functions (Type A) Display EXAMPLE 68LM562 (1) “TA” button (2) “RDM/PTY” button (3) “RPT/AF” button (4) UP button (5) DOWN button (6) “DISP” button (A) Band (B) Channel number (C) Program service (PS) name (3) (2) 75RM084 5-47...
Page 301 OTHER CONTROLS AND EQUIPMENT TA (Traffic Announcement) on/off PTY (Program Type) search AF (Alternative Frequency) on/off Press “TA” button (1). 1) Press “RDM/PTY” button (2) to select Press “RPT/AF” button (3). Each time it is pressed, TA adjustment is PTY mode. Each time it is pressed, AF adjustment is changed as follows: 2) Press “RDM/PTY”...
Page 302 OTHER CONTROLS AND EQUIPMENT TA standby At the moment traffic information is received while the source is set to CD, ® USB, iPod AUX, DAB, Blue- ® tooth audio with TA activated, the source is automatically changed to radio. After reception of traffic information, the source, which was selected before being changed to radio, resumes.
Page 303 OTHER CONTROLS AND EQUIPMENT Display Listening to a CD EXAMPLE Type A (1) Insertion slot (2) EJECT button (3) “CD” button (4) UP button (5) DOWN button (6) “RPT” button (7) “RDM” button (8)(6)(7) (8) “DISP” button Type B Type C (A) Track number (B) Play time NOTE:...
Page 304 OTHER CONTROLS AND EQUIPMENT NOTICE NOTICE • Never insert your finger or hand If you forcefully try to push an into the CD insertion slot. Never ejected CD inside the unit before auto insert foreign objects. reloading, the disc surface might be •...
Page 305 OTHER CONTROLS AND EQUIPMENT Random playback Display change Press “RDM” button (7). Press “DISP” button (8). Each time the button is pressed, the mode Each time the button is pressed, display will change as follows: will change as follows: Play time TRACK RANDOM Disc title Track title...
Page 306 OTHER CONTROLS AND EQUIPMENT Display Listening to an MP3/WMA/AAC disc EXAMPLE Type A (1) “TUNE/FLD PUSH SOUND” knob (2) UP button (3) DOWN button (4) “RPT” button (5) “RDM” button (6) “DISP” button (6)(4)(5) (A) Folder number (B) Track number Type B Type C (C) Play time...
Page 307 OTHER CONTROLS AND EQUIPMENT Selecting a folder Random playback Repeat playback Turn “TUNE/FLD PUSH SOUND” knob (1) Press “RDM” button (5). Press “RPT” button (4). to select a folder. Each time the button is pressed, the mode Each time the button is pressed, the mode will change as follows: will change as follows: Selecting a track...
Page 308 OTHER CONTROLS AND EQUIPMENT Display change Points to remember when making MP3/ Notes on MP3/WMA/AAC Press “DISP” button (6). WMA/AAC files Each time the button is pressed, display Common What is MP3? will change as follows: • High bit rate and high sampling fre- •...
Page 309 OTHER CONTROLS AND EQUIPMENT Recording MP3/WMA/AAC files on a CD Compression formats media • It is recommended not to write both CD- • Bit rate: DA files and MP3/WMA/AAC files on a MPEG1 Audio Layer III: 32 k - 320 kbps disc.
Page 310 OTHER CONTROLS AND EQUIPMENT Display Listening to files stored in a USB device EXAMPLE Type A (1) “MEDIA” button (2) “TUNE/FLD PUSH SOUND” knob (3) UP button (4) DOWN button (5) “RPT” button (6) “RDM” button (7) “DISP” button (7)(5)(6) (A) Folder number Type B Type C...
Page 311 OTHER CONTROLS AND EQUIPMENT Selecting a USB device mode Random playback • FOLDER REPEAT Press “MEDIA” button (1). Press “RDM” button (6). The repeat indicator “F.RPT” will light. Each time the button is pressed, the mode Each time the button is pressed, the mode All the tracks in the folder currently will change as follows: will change as follows:...
Page 312 OTHER CONTROLS AND EQUIPMENT USB device connection Compression formats Notes on USB device • When connecting a USB device, check that the connector is pushed all the way • Bit rate: Compatible USB devices into the port. MPEG1 Audio Layer III: 32 k - 320 kbps •...
Page 313 OTHER CONTROLS AND EQUIPMENT Display ® Listening to an iPod (7)(5)(6) EXAMPLE Type A (1) “MEDIA” button (2) “TUNE/FLD PUSH SOUND” knob (3) UP button (4) DOWN button (5) “RPT” button (6) “RDM” button (7) “DISP” button (8) PRESET buttons ([1] to [6]) (7)(5)(6) (7)(5)(6) Type B...
Page 314 OTHER CONTROLS AND EQUIPMENT ® Selecting an iPod mode Random playback Display change Press “MEDIA” button (1). Press “RDM” button (6). Press “DISP” button (7). Each time the button is pressed, the mode Each time the button is pressed, the mode Each time the button is pressed, display will change as follows: will change as follows:...
Page 315 OTHER CONTROLS AND EQUIPMENT Playing mode selection * Some functions may not be available ® Notes on iPod ® 1) Press the button numbered [6] of PRE- depending on the model of iPod ® ® SET buttons (8) for 1 second or longer. * iPod is a trademark of Apple Inc., regis- Supported iPod...
Page 316 OTHER CONTROLS AND EQUIPMENT AUX connection AUX function To listen to auxiliary audio sources (sold separately) through the unit, follow the instruction below. EXAMPLE Type A 1) Connect the auxiliary audio source to AUX/USB socket (separately attached) with an AUX cable. 2) Press “MEDIA”...
Page 317 OTHER CONTROLS AND EQUIPMENT NOTE: • Please consult your place of purchase for details about whether a given auxil- iary audio source can be connected and the proper auxiliary cord to use. • The volume and tone controls of the auxiliary audio source can be adjusted on the unit.
Page 318 OTHER CONTROLS AND EQUIPMENT Steering switch ® Bluetooth hands-free (Type A / Type B) (if equipped) (10) EXAMPLE Type A 75RM061 Type B ® (6) Bluetooth setup button (on steering wheel) (7) OFF HOOK button (8) ON HOOK button (9) MUTE switch (10) “VOL”...
Page 319 OTHER CONTROLS AND EQUIPMENT Phone registration 6) When the pairing with the phone is Adjusting the listening volume established, automatic transfer of the • Turn “VOL PUSH PWR” knob (2) during To use the hands-free function with this phonebook call history a call.
Page 320 OTHER CONTROLS AND EQUIPMENT Adjusting the call or ringtone volume Dialing using missed/incoming/ • Pressing “Confirm” after selecting “Add Follow the instructions below to adjust the outgoing calls Speed Dial” can register the selected call or ringtone volume. Follow the instructions below to dial to the number in the speed dial.
Page 321 OTHER CONTROLS AND EQUIPMENT 7) Turn “TUNE/FLD PUSH SOUND” knob 5) Turn “TUNE/FLD PUSH SOUND” knob Transfer of call history (Call History) (1) to select “Delete?” or “Delete All?”, (1) to select “Overwrite All” or “Add One Follow the instructions below to transfer and press the knob (1) to determine the Contact”, and press the knob (1) to call history of the registered phone.
Page 322 OTHER CONTROLS AND EQUIPMENT Automatic transfer of phonebook/call Making a call by phonebook Deletion of registered data (Delete history Follow the instructions below to dial a num- Entry) You can select whether or not the device ber registered in phonebook. Follow the instructions below to delete a transfers the phonebook and the call his- 1) Press OFF HOOK button (7).
Page 323 OTHER CONTROLS AND EQUIPMENT NOTE: register in speed dial, and press the One-touch call (Speed dial) When selecting “Go Back” or pressing knob (1) to determine the selection. Follow the instructions below to dial the BACK button (4), the previous menu will 6) Turn “TUNE/FLD PUSH SOUND”...
Page 324 OTHER CONTROLS AND EQUIPMENT Deletion of speed dial (Del Speed Dial) Display of device data (Device Name) Reset to the factory defaults Follow the instructions below to delete the Follow the instructions below to display the Follow the instructions below to reset all ®...
Page 325 OTHER CONTROLS AND EQUIPMENT Selection of phone (Select Phone) List of phones (List Phones) 3) Turn “TUNE/FLD PUSH SOUND” knob Follow the instructions below to select a Follow the instructions below to display the (1) to select “Passkey”, and press the phone to be paired with from the registered names of the registered phones in knob (1) to determine the selection.
Page 326 OTHER CONTROLS AND EQUIPMENT Deletion of phone information (Delete BT function on/off (BT Power) Phone) Follow the instructions below to turn on/off ® Follow the instructions below to delete the the Bluetooth function. ® registered phone information. 1) Press the Bluetooth setup button (5) ®...
Page 327 OTHER CONTROLS AND EQUIPMENT Steering switch ® Bluetooth audio (Type A / Type B) (if equipped) EXAMPLE Type A 75RM062 Display Type B (1) “MEDIA” button (2) “TUNE/FLD PUSH SOUND” knob (3) UP button (4) DOWN button (5) “DISP” button (6) BACK button ®...
Page 328 OTHER CONTROLS AND EQUIPMENT Registration of audio devices NOTE: Fast forwarding/rewinding a track • When selecting “Go Back” or pressing • Hold down UP button (3) to fast forward ® BACK button (6), the previous menu will the track. To use Bluetooth ready audio devices be displayed.
Page 329 OTHER CONTROLS AND EQUIPMENT Selection of audio device (Select Audio) List of audio devices (List Audio) 3) Turn “TUNE/FLD PUSH SOUND” knob Follow the instructions below to select an Follow the instructions below to display the (2) to select “Passkey”, and press the audio device to be paired with from the names of the registered audio devices in knob (2) to determine the selection.
Page 330 OTHER CONTROLS AND EQUIPMENT Deletion of audio device information ® Disclaimer for Bluetooth function Remote audio controls (if equipped) (Delete Audio) Follow the instructions below to delete the • Depending on compatibility of mobile Controlling basic functions of the audio ®...
Page 331 OTHER CONTROLS AND EQUIPMENT Adjusting the volume Selecting the radio station (AM, FM1, • To increase the volume, press the “VOL” FM2, DAB1, DAB2 mode) switch (1) up. The volume will continue • To select the next preset station, press to increase until the switch is released.
Page 332 OTHER CONTROLS AND EQUIPMENT The anti-theft function is intended to dis- Anti-theft feature courage thefts. For example, when the audio system is installed in another vehi- EXAMPLE cle, it will become unable to operate. Type A This function works by entering a Personal Identification Number (PIN).
Page 333 OTHER CONTROLS AND EQUIPMENT Setting the anti-theft function Canceling the anti-theft feature Confirming the Personal Identification 1) Press “VOL PUSH PWR” knob (1) to To cancel the anti-theft function, delete the Number (PIN) power off. registered PIN. When the main power source is discon- 2) Hold down the buttons numbered [1] 1) Press “VOL PUSH PWR”...
Page 334 OTHER CONTROLS AND EQUIPMENT Troubleshooting When encountering a problem, check and follow the instructions below. If the described suggestions do not solve the problem, it is recommended to take the unit to your authorized SUZUKI dealer. Problem Possible cause Possible solution Common When “SECURITY”...
Page 335 OTHER CONTROLS AND EQUIPMENT Problem Possible cause Possible solution MP3/WMA/AAC The disc contains unsupported formatted No playback Check the file format. data. Sound skipping may occur when playing Sound skips or noise produced It is not recommended to play VBR files. VBR (Variable Bit Rate) files.
Page 336 OTHER CONTROLS AND EQUIPMENT Error display messages Display Possible cause Possible solution Insert the disc with its label side up. Check the disc if it is not warped or is free of flaws. “ERROR 1” The disc cannot be read. When “ERROR 1”...
Page 337 OTHER CONTROLS AND EQUIPMENT Display Possible cause Possible solution ® Bluetooth ® Disconnect the Bluetooth ready device and connect it The player developed an error of an again. “ERROR 1” unidentified cause. When “ERROR 1” does not disappear, contact your dealer.
Page 338 OTHER CONTROLS AND EQUIPMENT MEMO 5-85 75RM0-01E...
Page 339 VEHICLE LOADING AND TOWING VEHICLE LOADING AND TOWING Vehicle loading ..............6-1 Trailer towing ............... 6-1 54G215 75RM0-01E...
Page 340: Vehicle Loading
VEHICLE LOADING AND TOWING Vehicle loading Trailer towing WARNING Never overload your vehicle. The Your vehicle was designed for specific gross vehicle weight (sum of the weight capacities. The weight capacities of weights of the vehicle, all the occu- your vehicle are indicated by the Gross pants, accessories, cargo plus trailer Vehicle Weight Rating (GVWR) and the nose weight if towing a trailer) must...
Page 341 We recommend that you use a genuine all trailer lights before you start to tow. camera brake support OFF switch SUZUKI tow bar (available as option), or and turn off the dual camera brake WARNING equivalent.
Page 342 VEHICLE LOADING AND TOWING pler, with the trailer fully loaded and the Tires WARNING coupler at its normal towing height. This weight can be measured using a bathroom Never overload cargo on your trailer scale. WARNING or your vehicle. Gross trailer weight The weight of your loaded trailer (gross must never exceed towing capacity.
Page 343 VEHICLE LOADING AND TOWING Additional trailer towing warnings WARNING WARNING Your vehicle should be handled in a (Continued) WARNING different way when towing a trailer. • Allow adequate stopping distance. For the safety of yourself and others, Stopping distance is increased Connect trailer lights and hook up observe the following precautions: when you tow a trailer.
Page 344 VEHICLE LOADING AND TOWING WARNING WARNING (Continued) When parking your vehicle and con- • Be careful when overtaking other nected trailer, always use the follow- vehicles. Allow enough room for ing procedure: your trailer before changing lanes, 1) Apply the vehicle’s brakes firmly. and use turn signal lights properly 2) Have another person place wheel in advance.
Page 345 VEHICLE LOADING AND TOWING Trailer hitch installation points Maximum vertical load on trailer hitch point (EU) 2WD models 50 kg (110 lbs) Maximum permissible overhang “a” 623 mm (24.5 in.) “a” (1) 75RM364 4WD models “a” (1) 75RM365 (1) Side (2) Diagonal 75RM0-01E...
Page 346 VEHICLE LOADING AND TOWING MEMO 75RM0-01E...
Page 347 INSPECTION AND MAINTENANCE INSPECTION AND MAINTENANCE Maintenance schedule ............7-2 Periodic maintenance schedule (except for EU countries and Israel) ........7-3 Maintenance recommended under severe driving conditions (except for EU countries and Israel) ....7-8 Periodic maintenance schedule (for EU countries and Israel) ..........7-13 Maintenance recommended under severe driving conditions (for EU countries and Israel) ......
Page 348 • Be careful not to touch a hot ing any electrical service work on engine, exhaust manifold your SUZUKI vehicle. Do not touch pipes, muffler, radiator and water air bag system components, seat hoses. belt pretensioner system compo- • Do not allow smoking, sparks, or nents or wires.
Page 349: Maintenance Schedule
SUZUKI recommends that mainte- nance on items marked with an aster- performed your authorized SUZUKI dealer or a quali- fied service technician. If you are qualified, you may perform mainte- nance on the unmarked items by referring to the instructions in this section.
Page 350 INSPECTION AND MAINTENANCE Periodic maintenance schedule (except for EU countries and Israel) “R” : Replace or Change “I” : Inspect, clean, adjust, lubricate or replace as necessary NOTE: • Class 1: K12C engine • Class 2: K12M engine NOTE: This table shows the service schedule up to 180000 km (108000 miles). Beyond 180000 km (108000 miles), perform the same services at the same intervals shown in the chart.
Page 351 #2: Perform the engine coolant level check under the daily inspection in the “OPERATING YOUR VEHICLE” section. If you use the engine coolant other than “SUZUKI LLC: Super (Blue)” for replacement, follow the schedule of “SUZUKI LLC: Stan- dard (Green)”.
Page 352 #2: Perform the engine coolant level check under the daily inspection in the “OPERATING YOUR VEHICLE” section. If you use the engine coolant other than “SUZUKI LLC: Super (Blue)” for replacement, follow the schedule of “SUZUKI LLC: Stan- dard (Green)”.
Page 353 – – – *6-7. Manual transaxle oil Genuine “SUZUKI GEAR OIL 75W” Inspect every 30000 km (18000 miles) or 24 months. Other than “SUZUKI GEAR OIL 75W” (I: 1st 15000 km only) – – – 6-8. Continuously variable transaxle (CVT) Fluid level –...
Page 354 – – – *6-7. Manual transaxle oil Genuine “SUZUKI GEAR OIL 75W” Inspect every 30000 km (18000 miles) or 24 months. Other than “SUZUKI GEAR OIL 75W” (I: 1st 15000 km only) – – – – 6-8. Continuously variable transaxle (CVT) Fluid level –...
Page 355 INSPECTION AND MAINTENANCE Maintenance recommended under severe driving conditions (except for EU countries and Israel) Follow this schedule if your vehicle is mainly operated under one or more of the following conditions: • When most trips are less than 6 km (4 miles). •...
Page 356 #2: Perform the engine coolant level check under the daily inspection in the “OPERATING YOUR VEHICLE” section. If you use the engine coolant other than “SUZUKI LLC: Super (Blue)” for replacement, follow the schedule of “SUZUKI LLC: Stan- dard (Green)”.
Page 357 #2: Perform the engine coolant level check under the daily inspection in the “OPERATING YOUR VEHICLE” section. If you use the engine coolant other than “SUZUKI LLC: Super (Blue)” for replacement, follow the schedule of “SUZUKI LLC: Stan- dard (Green)”.
Page 358 – – *6-7. Manual transaxle oil Genuine “SUZUKI GEAR OIL 75W” Inspect every 30000 km (18000 miles) or 24 months. Replace every 60000 km (36000 miles) or 48 months. Other than “SUZUKI GEAR OIL 75W” – – – – –...
Page 359 – *6-7. Manual transaxle oil Genuine “SUZUKI GEAR OIL 75W” Inspect every 30000 km (18000 miles) or 24 months. Replace every 60000 km (36000 miles) or 48 months. Other than “SUZUKI GEAR OIL 75W” – – – – 6-8. Continuously variable transaxle (CVT) Fluid level –...
Page 360 INSPECTION AND MAINTENANCE Periodic maintenance schedule (for EU countries and Israel) “R” : Replace or Change “I” : Inspect, clean, adjust, lubricate or replace as necessary NOTE: This table shows the service schedule up to 240000 km (150000 miles). Beyond 240000 km (150000 miles), perform the same services at the same intervals shown in the chart.
Page 361 #2: Perform the engine coolant level check under the daily inspection in the “OPERATING YOUR VEHICLE” section. If you use the engine coolant other than “SUZUKI LLC: Super (Blue)” for replacement, follow the schedule of “SUZUKI LLC: Standard (Green)”. 7-14...
Page 362 #2: Perform the engine coolant level check under the daily inspection in the “OPERATING YOUR VEHICLE” section. If you use the engine coolant other than “SUZUKI LLC: Super (Blue)” for replacement, follow the schedule of “SUZUKI LLC: Standard (Green)”. 7-15...
Page 363 – – – *6-7. Manual transaxle oil Genuine “SUZUKI GEAR OIL 75W” Inspect every 40000 km (25000 miles) or 24 months. Other than “SUZUKI GEAR OIL 75W” – – – *6-8. Auto Gear Shift oil Genuine “SUZUKI GEAR OIL 75W”...
Page 364 – – – *6-7. Manual transaxle oil Genuine “SUZUKI GEAR OIL 75W” Inspect every 40000 km (25000 miles) or 24 months. Other than “SUZUKI GEAR OIL 75W” – – – *6-8. Auto Gear Shift oil Genuine “SUZUKI GEAR OIL 75W”...
Page 365 INSPECTION AND MAINTENANCE Maintenance recommended under severe driving conditions (for EU countries and Israel) Follow this schedule if your vehicle is mainly operated under one or more of the following conditions: • When most trips are less than 6 km (4 miles). •...
Page 366 #2: Perform the engine coolant level check under the daily inspection in the “OPERATING YOUR VEHICLE” section. If you use the engine coolant other than “SUZUKI LLC: Super (Blue)” for replacement, follow the schedule of “SUZUKI LLC: Standard (Green)”. 7-19...
Page 367 #2: Perform the engine coolant level check under the daily inspection in the “OPERATING YOUR VEHICLE” section. If you use the engine coolant other than “SUZUKI LLC: Super (Blue)” for replacement, follow the schedule of “SUZUKI LLC: Standard (Green)”. 7-20...
Page 368 *6-7. Manual transaxle oil Genuine “SUZUKI GEAR OIL 75W” Inspect every 20000 km (12500 miles) or 12 months. Replace every 80000 km (50000 miles) or 48 months. Other than “SUZUKI GEAR OIL 75W” – – – *6-8. Auto Gear Shift oil Genuine “SUZUKI GEAR OIL 75W”...
Page 369 *6-7. Manual transaxle oil Genuine “SUZUKI GEAR OIL 75W” Inspect every 20000 km (12500 miles) or 12 months. Replace every 80000 km (50000 miles) or 48 months. Other than “SUZUKI GEAR OIL 75W” – – – *6-8. Auto Gear Shift oil Genuine “SUZUKI GEAR OIL 75W”...
Page 370: Drive Belt
(1) Front If you need to replace or adjust the belt (2) Rear 68PM00733 have it done by your SUZUKI dealer. (3) Generator (1) Preferred (4) Water pump (5) Air conditioner compressor Check that the engine oil you use comes...
Page 371 SAE 0W-16 (1) is the best choice for good fuel economy and good starting in cold weather. NOTE: We recommend that you use SUZUKI gen- uine oil. To purchase it, see your SUZUKI 71LST0701 dealer. (1) Preferred 80G064 Be sure that the engine oil you use comes...
Page 372 INSPECTION AND MAINTENANCE It is important to keep the engine oil at the Refilling Changing engine oil and filter correct level for proper lubrication of your vehicle’s engine. Check the oil level with Drain the engine oil while the engine is still the vehicle on a level surface.
Page 373 Keep tor the next oil change timing properly. new and used oil and used oil filters To reset the light, consult your SUZUKI away from children and pets. dealer. If you reset it by yourself, refer to Repeated, prolonged contact with “Setting mode”...
Page 374 (2) 3/4 turn • When replacing the oil filter, it is recommended that you use a genu- NOTICE ine SUZUKI replacement filter. If To tighten the oil filter properly, it is you use an aftermarket filter, check important to accurately identify the...
Page 375: Engine Coolant
Failure to use the proper coolant can dam- Coolant level check Engine coolant age your cooling system. Your authorized SUZUKI dealer can help you select the Check the coolant level at the reservoir proper coolant. tank, not at the radiator. With the engine...
Page 376: Air Cleaner
Failure to follow this can result in coolant leak- age. Coolant replacement Since special procedures are required, ask your authorized SUZUKI dealer for this job. 7-29 75RM0-01E...
Page 377 INSPECTION AND MAINTENANCE (For K12M engine model) (2) (3) 81P60040 81P60050 75RM064 2) To disconnect the coupler (2), pull the 3) Unclamp the side clamps (4), then pull 1) Unclamp the side clamps and remove release lever (3) toward you and then the air cleaner case toward you.
Page 378: Spark Plugs
INSPECTION AND MAINTENANCE Spark plugs EXAMPLE Loosen Spark plug replacement and inspec- Correct Wrong tion Tighten (For K12C engine model) EXAMPLE 78K179 60G160 NOTICE NOTICE • When pulling out the ignition coils, • When installing the spark plugs, do not pull on the cable. Pulling on screw them in with your fingers to the cable can damage it.
Page 379 Specified fluid ing a trailer. Wait until the fluid cools down (about 30 minutes), or the fluid level indi- Use a CVT fluid SUZUKI CVT FLUID cation will not be correct. GREEN-2. 2) Park your vehicle on level ground.
Page 380 EXAMPLE Since special procedures, materials and tools are required to check the deteriora- tion of CVT oil or change, it is recom- mended that you trust this job to your authorized SUZUKI dealer. 75F086 75RM336 (1) FULL (2) LOW EXAMPLE...
Page 381: Gear Oil
INSPECTION AND MAINTENANCE We highly recommend you use “SUZUKI Gear oil level check Gear oil GEAR OIL 75W-85” for transfer oil (4WD) and rear differential oil (4WD). Manual transaxle / Auto Gear Shift Manual transaxle oil / Auto Gear Transfer oil (4WD)
Page 382 Since special procedures, materials and until the oil level reaches the bottom of tools are required, ask your authorized the filler hole, and then reinstall the SUZUKI dealer for this job. plug. Tightening torque for oil filler and level plug Manual transaxle (1): 21 Nm (2.1 kg-m, 15.5 lb-ft)
Page 383: Clutch Pedal
(the engine must be running with the parking brake fully disengaged). Should the light come on, immedi- ately ask your SUZUKI dealer to inspect the brake system. • A rapid fluid loss indicates leakage in the brake system which should be inspected by your SUZUKI dealer immediately.
Page 384 • Uneven braking (brakes not work- Since your vehicle’s brake system is self- by your SUZUKI dealer. If you doubt the ing uniformly on all wheels.) adjusting, there is no need for pedal brake pedal is at its normal height, check it •...
Page 385 SUZUKI dealer. SUZUKI dealer. 7-38 75RM0-01E...
Page 386 INSPECTION AND MAINTENANCE the tire pressure seems to be good in this Tire inspection Tires condition, it could fall below the specified pressure when tires cool down. Also, tires Inspect your vehicle’s tires at least once a that are inflated to the specified pressure month by performing the following checks: in a warm garage may have pressure 1) Measure the air pressure with a tire...
Page 387 For 4WD models, replacing a tire with one of a different size, or using differ- 52KM110 • Your SUZUKI vehicle is equipped ent brands among the four tires can (1) Tread wear indicator with tires which are all the same result in damage to the drive train.
Page 388 INSPECTION AND MAINTENANCE Note that two or more compact spare tires Tire rotation Compact spare tire (if equipped) should not be used on one vehicle simulta- neously. 4-tire rotation WARNING The compact spare tire and wheel are intended for temporary emergency use only.
Page 389 INSPECTION AND MAINTENANCE Carefully read the instructions in the fol- Lead-acid battery Battery lowing sections, “Lead-acid battery” and “Lithium-ion battery”, for the correct han- This vehicle is equipped with the following dling of each battery. WARNING batteries. • The lead-acid battery and lithium-ion •...
Page 390 INSPECTION AND MAINTENANCE Replacement of the battery NOTICE EXAMPLE (For vehicles without ENG A-STOP sys- If your vehicle is equipped with the tem) ENG A-STOP system, it uses a lead- EXAMPLE acid battery specifically for the high- efficiency A-STOP system, observe the following precautions.
Page 391 2) Tighten the bracket bolt and battery (Battery label) used battery, consult your SUZUKI dealer. cables securely. NOTE: When the battery is disconnected, some of the vehicle’s function will be initialized and/ or deactivated.
Page 392 These fuses are between the main fuse battery. and individual fuses, and are for electrical • When replacing or disposing of the lith- load groups. ium-ion battery, consult your authorized SUZUKI dealer. Individual fuses These fuses are for individual electrical cir- WARNING cuits. 74LHT0715...
Page 393 When replacing the (26) – Blank main fuse, a primary fuse or an individual 100 A fuse, use a genuine SUZUKI replacement. (27) 15 A Headlight high (Left) 50 A To remove a fuse, use the fuse puller pro-...
Page 394 PRIMARY FUSE If the main fuse or a primary fuse 30 A Power window blows, have your vehicle inspected 10 A Meter by an authorized SUZUKI dealer. Always genuine SUZUKI 15 A Ignition coil replacement. Never use a substitute Ignition-1 signal 2...
Page 395: Headlight Aiming
(21) 20 A Power window timer Headlight aiming (22) Since special procedures are required, ask (23) 15 A Horn your authorized SUZUKI dealer for this job. (24) Tail light (Left) (25) 10 A Tail light (26) 10 A Air bag...
Page 396: Bulb Replacement
To install it, simply push it back in. recommend you take your vehicle to your • Light bulbs can be hot enough to Front SUZUKI dealer for bulb replacement. burn your finger right after turning off lights. This is true especially for Halogen headlights (if equipped) halogen headlight bulbs.
Page 397 INSPECTION AND MAINTENANCE Side turn signal light (if equipped) 75RM068 75RM069 2) Push the retaining spring (3) forward NOTE: and unhook it. Then remove the bulb. You can see the position of retaining spring 64J195 Install a new bulb in the reverse order from the hole (4) of headlight.
Page 398 Then turn off the engine. SUZUKI dealer for bulb replacement. Models with halogen headlights 1) Start the engine. Turn the steering wheel to the opposite side of the fog light to be replaced the bulb easily.
Page 399 INSPECTION AND MAINTENANCE Bulb Other general lights EXAMPLE EXAMPLE Bulb holder EXAMPLE 75RM244 54G124 3) Open the end of the cover inside the (3) Removal fender. Disconnect the coupler by push- (4) Installation ing the lock release. Turn the bulb 54G123 holder counterclockwise and remove it.
Page 400 INSPECTION AND MAINTENANCE Front turn signal light (1) Rear combination light Reversing light Front position light (2) Models with halogen headlights 75RM070 62R0122 Remove the bolts (1) and pull the light 1) Open the tailgate and remove the trim housing (2) straight. (1) of the tailgate.
Page 401 INSPECTION AND MAINTENANCE License plate light 62R0378 75RM073 75RM071 2) Disconnect the coupler (2) by pushing 2) Open the end of the cover inside the Rear fog light (if equipped) the lock release. Turn the bulb holder of fender. the reversing light (3) counterclockwise and remove it.
Page 402: Wiper Blades
INSPECTION AND MAINTENANCE NOTE: Wiper blades Some wiper blades may be different from the ones described here depending on vehicle specifications. If so, consult your SUZUKI dealer for proper replacement method. For windshield wipers: EXAMPLE EXAMPLE 61MM0A210 2) Open the lock (1), slide the wiper frame...
Page 403 INSPECTION AND MAINTENANCE 3) Pull the locked end of the wiper blade firmly to unlock the blade and slide the EXAMPLE EXAMPLE blade out as shown. EXAMPLE 61MM0B098 61MM0A212 (A) Up (B) Down 71LMT0708 NOTE: (3) Retainer When you install the metal retainers (3), make sure the direction of metal retainers 4) If the new blade is provided without the as shown in the above illustrations.
Page 404 INSPECTION AND MAINTENANCE For rear wipers: EXAMPLE EXAMPLE EXAMPLE 61MM0A213 65D151 (4) Locked end NOTE: Do not flex the wiper blade frame end more 5) Install the new blade in the reverse than necessary. If you do, it can break off. order of removal, with the locked end (4) positioned toward the wiper arm.
Page 405: Windshield Washer Fluid
INSPECTION AND MAINTENANCE Windshield washer fluid Air conditioning system EXAMPLE If you do not use the air conditioner for a long period, such as during winter, it may EXAMPLE not give the best performance when you start using it again. To help maintain opti- mum performance and durability of your air conditioner, it needs to be run periodically.
Page 406 INSPECTION AND MAINTENANCE Air conditioner filter replacement (if equipped) Since special procedures are required, ask your authorized SUZUKI dealer for this job. EXAMPLE 75RM075 75RM074 2) Remove the cover (1) and pull out the 1) To approach the air conditioner filter, air conditioner filter (2).
Page 407 EMERGENCY SERVICE EMERGENCY SERVICE Tire changing tool ............... 8-1 Jacking instructions ............8-1 Flat tire repair kit (if equipped) .......... 8-5 Jump-starting instructions ..........8-10 Towing .................. 8-11 Engine trouble: Starter does not operate ......8-13 Engine trouble: Flooded engine ........8-13 Engine trouble: Overheating ..........
Page 408: Tire Changing Tool
EMERGENCY SERVICE Tire changing tool Jacking instructions WARNING After using the tire changing tools, stow them securely or they can EXAMPLE cause injury if an accident occurs. CAUTION The jack should be used only to change wheels. It is important to read the jacking instructions in this sec- tion before attempting to use the jack.
Page 409 EMERGENCY SERVICE 3) Turn on the hazard warning flasher if 6) Position the jack at an angle as shown your vehicle is near traffic. in the illustration and raise the jack by 4) Block the front and rear of the wheel turning the jack handle clockwise until diagonally opposite of the wheel being the jack-head groove fits around the...
Page 410 EMERGENCY SERVICE Raising vehicle with garage jack • Apply the garage jack to one of the points indicated below. • Always support the raised vehicle with jack stands (commercially available) at the points indicated below. 75RM360 (1) Front (4) Rear (7) Jacking point for garage jack (2) Jack stand (5) Rear (4WD)
Page 411 EMERGENCY SERVICE NOTE: 4) Remove the wheel nuts and wheel. For more details, contact an authorized SUZUKI dealer. Changing wheels To change a wheel, use the following pro- cedure: 1) Remove the jack (if equipped), tools and spare wheel from the vehicle.
Page 412 EMERGENCY SERVICE Full wheel cover (if equipped) Flat tire repair kit (if equipped) EXAMPLE The flat tire repair kit is stowed in the lug- EXAMPLE gage compartment. Refer to “LUGGAGE COMPARTMENT” in the “ILLUSTRATED TABLE OF CON- TENTS” section. WARNING Failure to follow the instructions in this section for using the flat tire repair kit can result in an increased...
Page 413 Flat tire repair kit contents WARNING The flat tire repair kit cannot be used in EXAMPLE the following cases. Consult a SUZUKI Flat tire repair kit sealant is harmful if dealer or a roadside assistance service. swallowed, or if it comes in contact •...
Page 414 EMERGENCY SERVICE Emergency repair 1) Place the vehicle on level, hard ground. Set the parking brake firmly and shift into “R” (Reverse) if your vehicle has a manual transaxle/Auto Gear Shift, or shift into “P” (Park) if your vehicle has a CVT.
Page 415 In this case, the flat tire repair kit cannot provide the necessary 81PN120 seal. Consult a SUZUKI dealer or a road- 7) Screw the air hose (10) of the compres- side assistance service. sor (1) to the tire valve (8). Fit the...
Page 416 (TPMS) sensor (if equipped) cannot provide the necessary seal. Do must be renewed. not use the tire and consult a SUZUKI Dispose of the sealant bottle at a dealer or a roadside assistance service. SUZUKI dealer or in accordance with your regional codes and practices.
Page 417 • If your lead-acid battery discharges repeatedly, for no apparent reason, have your vehicle inspected by an authorized SUZUKI dealer. • To avoid harm to yourself or dam- age to your vehicle or battery, fol- low the jump-starting instructions below.
Page 418 EMERGENCY SERVICE Towing WARNING Never connect the jump lead directly If you need to have your vehicle towed, to the negative (–) terminal of the dis- contact a professional service. Your dealer charged battery, or an explosion may can provide you with detailed towing occur.
Page 419 EMERGENCY SERVICE 2-wheel drive (2WD) CVT 2-wheel drive (2WD) manual tran- NOTICE saxle or Auto Gear Shift CVT vehicles may be towed using either of After shifting the Auto Gear Shift the following methods. Manual transaxle vehicles or Auto Gear gearshift lever to the “N”...
Page 420 Do not open the hood when inspected your authorized steam is present. When the steam SUZUKI dealer. NOTE: can no longer be seen or heard, open If the engine refuses to start, the starter the hood to see if the coolant is still motor automatically stops after a certain boiling.
Page 421 If engine overheats and you are not sure perature is high, because scalding what to do, contact your SUZUKI dealer. fluid and steam may be blown out under pressure. The cap should only be taken off when the coolant temperature has lowered.
Page 422 EMERGENCY SERVICE MEMO 8-15 75RM0-01E...
Page 423 APPEARANCE CARE APPEARANCE CARE Corrosion prevention ............9-1 Vehicle cleaning ..............9-2 60G412 75RM0-01E...
Page 424: Corrosion Prevention
APPEARANCE CARE 4) High temperatures will cause an accel- Remove foreign material deposits Corrosion prevention erated rate of corrosion to parts of the Foreign material such as salts, chemicals, vehicle which are not well-ventilated to road oil or tar, tree sap, bird droppings and It is important to take good care of your permit quick drying.
Page 425: Vehicle Cleaning
APPEARANCE CARE are spilled or leaked, clean and dry the Vehicle cleaning WARNING area immediately. On models equipped with the ENG A- Store your vehicle in a dry, well-venti- STOP system, there is a lithium-ion lated area battery under the front passenger’s Do not park your vehicle in a damp, poorly- seat.
Page 426 APPEARANCE CARE Leather upholstery Seat belts Cleaning interior Remove loose dirt with a vacuum cleaner. Clean seat belts with a mild soap and Using a mild soap or saddle soap solution, water. Do not use bleach or dye on the Vinyl upholstery wipe dirt off with a clean damp soft cloth.
Page 427 APPEARANCE CARE When washing the vehicle, park it in the Washing NOTICE place where direct sunlight does not fall on it and follow the instructions below: Do not use chemical products that 1) Flush the underside of body and wheel WARNING contain silicon to wipe electrical housings with pressurized water to...
Page 428 APPEARANCE CARE 3) Wash the entire exterior with a mild Washing by an automatic car wash Waxing detergent or car wash soap using a NOTICE sponge or soft cloth. The sponge or cloth should be frequently soaked in the If you use an automatic car wash, soap solution.
Page 429 GENERAL INFORMATION GENERAL INFORMATION Vehicle identification ............10-1 Fuel consumption ............... 10-2 84MM01001 75RM0-01E...
Page 430: Vehicle Identification
Whenever you have occasion tion. 75RM337 to consult your SUZUKI dealer, remember to identify your vehicle with this number. Should you find the number difficult to read, you will also find it on the identifica- tion plate.
Page 431: Fuel Consumption
GENERAL INFORMATION Fuel consumption For Europe Euro VI M/T: Manual transaxle 2WD: 2-wheel drive 4WD: 4-wheel drive K12C without ENG A-STOP K12C with ENG A-STOP 5.5/125 5.9/133 4.9/110 5.2/117 Urban (L/100km)/CO (g/km) Auto Gear Shift 5.5/125 – – – 4.1/92 4.5/103 4.0/90 4.4/100...
Page 432 GENERAL INFORMATION For Israel Euro VI M/T: Manual transaxle CVT: Continuously variable transaxle K12C 5.6/126 Urban (L/100km)/CO (g/km) 5.7/129 4.1/93 Extra-urban (L/100km)/CO (g/km) 4.3/98 4.6/105 Combined (L/100km)/CO (g/km) 4.8/109 NOTE: As these data are obtained under certain specific conditions, actual fuel consumption of your vehicle will be different from these data. 10-3 75RM0-01E...
Page 433 SPECIFICATIONS SPECIFICATIONS NOTE: Specifications are subject to change without notice. M/T: Manual transaxle 2WD: 2-wheel drive CVT: Continuously variable transaxle 4WD: 4-wheel drive ITEM: Dimensions UNIT: mm (in.) Overall length 3700 (145.7) Overall width without 1660 (65.4) wheel arch extensions with 1690 (66.5) wheel arch extensions...
Page 434 12V 20HR 45Ah CCA 295A 46B24 (JIS) Lead-acid battery 12V 20HR 55Ah CCA 450A LN1 (EN) with ENG A-STOP system Lithium-ion battery Maintenance free Fuses See “INSPECTION AND MAINTENANCE” section. *1 For about replacing or disposing of the lithium-ion battery, consult your SUZUKI dealer. 11-2 75RM0-01E...
Page 435 SPECIFICATIONS ITEM: Lights WATTAGE BULB No. Headlight Halogen headlight 12V 60/55W LED headlight – Front fog light (if equipped) 12V 19W Position light 12V 5W – Daytime running light (if equipped) 12V 13W P13W – Turn signal light Front 12V 21W WY21W Rear 12V 21W...
Page 436 • Check that they are tires of the same size, structure and load capacity as the originally installed tires. • Mount the snow tires on all four wheels. • Understand that the maximum permissible speed of snow tires is generally less than the originally installed tires. Consult your SUZUKI dealer or supplier for further information. 11-4 75RM0-01E...
Page 437 K12C 4.2 L (7.4 Imp pt) engine (including reservoir tank) models Auto Gear 4.0 L (7.0 Imp pt) “SUZUKI LLC: Super (Blue) Coolant” Shift (including reservoir tank) 3.8 L (6.7 Imp pt) K12M (including reservoir tank) engine 4.0 L (7.0 Imp pt)
Page 438 SPECIFICATIONS ITEM: Recommended fuel / lubricants and capacities (approx.) Manual transaxle oil/ “SUZUKI GEAR OIL 75W” 1.5 L (2.6 Imp pt) Auto Gear Shift oil CVT fluid SUZUKI CVTF GREEN-2 5.73 L (10.1 Imp pt) Transfer oil “SUZUKI GEAR OIL 75W-85”...
Page 439 SUPPLEMENT SUPPLEMENT For GCC countries .............. 12-1 For Chile and Panama ............12-3 75RM0-01E...
Page 440 SUPPLEMENT For GCC countries Technical data 1.2L Max power : 61kW/6000 rpm Max torque : 113Nm/4200 rpm Max speed : 170km/h (2WD M/T) 160km/h (2WD CVT) 12-1 75RM0-01E...
Page 441 SUPPLEMENT 12-2 75RM0-01E...
Page 442 Fuel system damage or vehicle performance problems resulting from the use of such fuels are not the NOTICE responsibility of SUZUKI and may not be 75RM172 Be careful not to spill fuel containing covered under the New Vehicle Warranty.
Page 443 INDEX INDEX Battery...................7-42 Symbols Battery replacement............2-12, 2-15 “SET” indicator light ............2-114 ® Bluetooth audio..............5-74 ® Bluetooth hands-free ............5-65 Accelerator pedal..............3-12 Brake assist system.............3-76 Accessory socket ..............5-6 Brake discs and brake drums ..........7-38 Adding coolant..............7-28 Brake fluid................7-36 Adjusting headlight pattern ..........
Page 444 INDEX Continuously variable transaxle (CVT) fluid ..... 7-32 Coolant level check ............. 7-28 Eco-Cool ................3-48 Coolant replacement ............7-29 Eco-driving display .............. 2-78 Corrosion prevention ............9-1 Electric mirrors..............2-24 Cruise control ..............3-48 Electric power steering light ..........2-108 Cruise indicator light............2-114 Electric window controls.............2-21 ®...
Page 445 INDEX Flat tire repair kit..............8-5 Gasoline engine ..............1-1 Floor mats ................5-10 Gasoline-ethanol blends ............1-1 Fluid level check ..............7-32 Gasoline-methanol blends ............ 1-1 Folding rear seats..............2-31 Gear oil..................7-34 Footrest ................5-10 Gear oil change ..............7-35 For Chile and Panama ............
Page 446 INDEX Hill hold control system ............3-84 Horn ..................2-127 Keyless entry system transmitter........2-7, 2-13 How ABS works ..............3-77 Keyless push start system............ 3-6 Keyless push start system remote controller ..... 2-7 I/S AC Settings ..............3-48 Keys..................2-1 Idling stop time ..............
Page 447 INDEX Periodic maintenance schedule (except for EU countries and Israel)........7-3 Main beam (high beam) indicator light ......2-111 Periodic maintenance schedule Maintenance recommended under severe driving (for EU countries and Israel) ..........7-13 conditions (except for EU countries and Israel) ....7-8 Pinching prevention function ..........
Page 448 Tire chains ................4-5 Shoulder anchor height adjuster ........2-40 Tire changing tool ..............8-1 SHVS (Smart Hybrid Vehicle by Suzuki)......3-46 Tire inspection..............7-39 Side air bags and side curtain air bags ......2-60 Tire pressure monitoring system (TPMS)......3-85 Side door locks ..............
Page 449 INDEX Using transaxle ..............3-17 Vehicle cleaning..............9-2 Vehicle identification............10-1 Vehicle loading ..............6-1 Warning and indicator lights ..........2-100 Warning and indicator messages ......2-81, 3-70 Washing.................. 9-4 Waxing ..................9-5 Windows ................2-20 Windshield washer ............2-125 Windshield washer fluid............
Page 450 INDEX MEMO 13-8 75RM0-01E...
Page 451 When you intend to use RF transmitting equipment in your vehicle, we strongly recommend that you select the equipment which con- forms to applicable rules or regulations in your country, and consult your SUZUKI dealer or qualified service technician for advice.
Page 452 75RM0-01E...
Page 453 75RM0-01E...
Page 454 75RM0-01E...
Page 455 75RM0-01E...
Page 456 Model:S180052024 Model:40398036 75RM0-01E...
Page 457 DECLARATION of CONFORMITY Approved by TRA 75RM0-01E...
Page 458 DECLARATION of CONFORMITY Approved by TRA S180052024 40398036 REGISTERED No : REGISTERED No : ER37742/15 ER38555/15 DEALER No : DEALER No : DA36975/14 DA36975/14 75RM0-01E...
Page 459 DECLARATION of CONFORMITY Approved by TRA REGISTERED No : ER45345/16 DEALER No : DA0052708/10 75RM0-01E...
Page 460 DECLARATION of CONFORMITY Approved by OMAN-TRA 75RM0-01E...
Page 461 DECLARATION of CONFORMITY Approved by OMAN-TRA 40398036 S180052024 OMAN-TRA OMAN-TRA R/1293/10 R/1445/10 D090258 D090258 75RM0-01E...
Page 462 DECLARATION of CONFORMITY Approved by OMAN-TRA OMAN-TRA R/3086/16 D090024 75RM0-01E...
Page 463 75RM0-01E...
Page 464 75RM0-01E...
Page 465 K68PB ‫דגם‬ ‫תנאים מיוחדים והערות משרד התקשורת‬ 433.92MHz ‫הכוללת מקלט בתדר‬ 125KHz ‫לרכב בתדר‬ IMMOBILIZER ‫מערכת‬ ‫אחרות הפועלות כדין‬ ‫לא מוגן מהפרעות וללא הפרעה למערכות‬ ‫השימוש במכשיר פטור מריון הפעלה אלחוטי‬ ‫. א‬ ‫מחייב רישיון מיוחד‬ ‫לצד ג‬ " ‫שרות בזק‬ "...
Page 466 " " " " " " 75RM0-01E...
Page 467 BATTERY LABEL SYMBOL MEANINGS No smoking, no naked flames, no sparks Battery acid Shield eyes Note operating instructions Keep away from children Explosive gas Prepared by August, 2016 Part No. 99011-75RM0-01E Printed in Japan TP464 75RM0-01E...

Suzuki IGNIS Series 2016 Owner's Manual

Quick Links

Need help?

Questions and answers

Related Manuals for Suzuki IGNIS Series 2016

Summary of Contents for Suzuki IGNIS Series 2016

Table of Contents