Summary of Contents for Delta Childrens Products 7595
Page 1
114 West 26th Street New York, NY 10001 Tele.212-645-9033 STYLE No: 7595 COLOR THIS PRODUCT IS NOT INTENDED FOR INSTITUTIONAL OR COMMERCIAL USE. If you have any questions or missing parts, contact us. DO NOT return product parts to the store from where it was purchased before contacting Delta Children’s Products Customer Service.
WARNING CHANGING TABLE Fall hazard - to prevent death or serious injury, always keep child within arm’s reach. Read all instructions before use of the changing table. KEEP THESE INSTRUCTIONS IN A SAFE PLACE FOR FUTURE USE. Inspect the changing table periodically. Do not use the changing table if it is damaged or broken. Contact Delta Children’s Products with any questions.
Page 3
PARTS: MAKE SURE THAT ALL PRE-ASSEMBLED PARTS ARE TIGHT. C. BACK TOP RAIL x 1 PART # 21682 D. BACK MIDDLE RAIL x 1 PART # 21683 E. FRONT TOP RAIL x 1 PART # 21684 B. RIGHT END FRAME x 1 A.
Page 4
SECTION 1: CHANGING TABLE ASSEMBLY STEP 1 PARTS AND TOOLS REQUIRED TO COMPLETE STEP D. BACK MIDDLE RAIL x 1 K. M6 x35 mm BOLT x 6 F. LOWER RAIL x 4 M4 ALLEN WRENCH SUPPLIED E. FRONT TOP RAIL x 1 A.
Page 5
SECTION 1: CHANGING TABLE ASSEMBLY STEP 2 PARTS AND TOOLS REQUIRED TO COMPLETE STEP G. TOP SHELF x 1 H. LOWER SHELF x 2 FROM STEP 1 ROTATE THE TOP SHELF SUPPORT 90 DEGREES. LAY THE LEFT END FRAME ON THE FLOOR, RAILS UP. SLIDE THE TOP SHELF (PART G) IN THE GROOVES ON THE BACK MIDDLE RAIL AND FRONT TOP RAIL, INTO THE GROOVE ON THE LEFT END FRAME, INSERT THE PINS ON THE TOP SHELF INTO THE HOLES IN THE RAILS.
Page 6
SECTION 1: CHANGING TABLE ASSEMBLY STEP 3 PARTS AND TOOLS REQUIRED TO COMPLETE STEP FROM STEP 2 K. M6 x35 mm BOLT x 6 M4 ALLEN WRENCH B. RIGHT END FRAME x 1 SUPPLIED ATTACH (1) RIGHT END FRAME (PART B) TO THE ASSEMBLY FROM STEP 2 WITH (6) M6x35 mm BOLTS (PART K) USING THE M4 ALLEN WRENCH AS SHOWN.
Page 7
SECTION 1: CHANGING TABLE ASSEMBLY STEP 4 PARTS AND TOOLS REQUIRED TO COMPLETE STEP FROM STEP 3 K. M6 x35 mm BOLT x 2 C. BACK TOP RAIL x 1 M4 ALLEN WRENCH SUPPLIED INSERT THE TENON OF THE BACK TOP RAIL (PART C) INTO THE SLOT ON THE TOP OF THE BACK MIDDLE RAIL (PART D), THEN INSERT (2) M6x35 mm BOLTS (PART K), THROUGH THE REAR LEGS INTO THE THREADED INSERTS ONTO THE BACK MIDDLE RAIL (PART D).
SECTION 1: CHANGING TABLE ASSEMBLY STEP 5 PARTS AND TOOLS REQUIRED TO COMPLETE STEP M4 ALLEN WRENCH SUPPLIED J. FOAM PAD x 1 FROM STEP 4 1. CHECK THAT THE BOLT SECURING THE STRAP IS TIGHT USING THE M4 ALLEN WRENCH. 2.
SECTION 1: CHANGING TABLE ASSEMBLY FINAL RESTRAINT HARNESS SYSTEM USE: . PLACE THE INFANT ON THE CHANGING TABLE FOAM PAD. . POSITION THE RESTRAINT HARNESS OVER THE MIDDLE OF THE INFANT’S TORSO AND INSERT THE BUCKLED ENDS INTO EACH OTHER UNTIL THE LOCK SHUT WITH A CLICK.
Consumer Care: www.deltachildrensproducts.com Delta Children’s Products 114 West 26th Street New York, NY 10001 Tele.212-645-9033 Warranty: This Delta Product is warranted to be free from defects for a period of 90 days from the date of purchase under normal use. This warranty extends only to the original retail purchaser and is valid only when supplied with proof of purchase, or if received as a gift, when the registration is on file with Delta.
Need help?
Do you have a question about the 7595 and is the answer not in the manual?
Questions and answers