Table of Contents
Advertisement
Quick Links
TS4000/DA Series
Overhead Door Closer
Installation Instructions
Components Checklist:
1 x Closer body and cover
1 x Arm assembly
1 x M6 Allen bolt
4 x M5 x 20mm Pan head screws
1 x Plastic spindle cover
User Information for Door Closers
This information must be observed. Non compliance will
absolve the manufacture from any liability. The door closer
must only be used in accordance with its intended use; i.e.
closing of side hung doors following manual opening.
Incorrect use may cause injury
Obstruction of closing process (e.g. dragging doors,
sticking weather strips/sealing rubbers, rough-running
locks)
Incorrect installation and adjustment (e.g. slamming
doors)
Danger of finger trap between frame and door leaf.
Wrong size door closer.
Closer used for other purpose than to close side hung
doors.
Maintenance:
NOTE:
Maintenance to be carried out by a specialist only.
Check assembly for tolerance and undue wear.
Tighten any screws that may have become loose.
At least once a year:
Grease moveable parts.
Check operation of doors and adjust if necessary.
For door closers subject to release by Electro
Mechanical and Electro Hydraulic means ensure that
local regulation are adhered to.
Installation and adjustment by specialist only
Where necessary, an additional doorstop or buffer must be
fitted to limit the maximum opening of the door. This is of
particular relevance for slide rail closers where the opening
angle may be limited by frame. For further explanations
see catalogue preface and product information.
Door handing - DIN left / right
Stand facing the door on the hinge / pull side. If the hinge
or pivot is to your right hand side the door is considered to
be DIN right. If the hinge or pivot is to your left-hand side
the door is considered to be DIN left.
IMPORTANT WARNING:
HIGH INTERNAL PRESSURES, UNDER NO CIRCUMSTANCES
ATTEMPT TO DISMANTLE THE CLOSER.
4 x 5 x 55mm Self-tapping countersunk screws
4 x M5 x 55mm Countersunk screws
1 x Adjustment screw (fitted to arm)
WARNING: DOOR CLOSERS WITH A POWER RATING
LOWER THAN 3 OR WITH MECHANICAL HOLD OPEN
DEVICES ARE NOT SUITABLE FOR USE WITH FIRE
DOORS.
Tools Required For Installation:
Flat head screwdriver
Posidrive screwdriver
Power drill
4.2mm drill bit
Template (supplied)
Pencil
10mm Spanner
5mm Allen key (supplied)
M5 Tap and Tap wrench
(steel door mounting)
Advertisement
Table of Contents
Related Manuals for GEZE TS4000
Summary of Contents for GEZE TS4000
- Page 1 TS4000/DA Series WARNING: DOOR CLOSERS WITH A POWER RATING Overhead Door Closer LOWER THAN 3 OR WITH MECHANICAL HOLD OPEN DEVICES ARE NOT SUITABLE FOR USE WITH FIRE Installation Instructions DOORS. Components Checklist: Tools Required For Installation: 1 x Closer body and cover...
- Page 2 (see figure 1 and 2 above.) Secure closer body with screws provided, making sure that the spindle is positioned towards the hinge side. (See figure 1 and 2 above.) The power size (closing force) of the TS4000 is fig. 3 adjusted by turning the Allen key screw situated above and to the right of the clear glass indicator tube containing a small ball bearing.
- Page 3 (see figure 1 and 2 above.) Secure closer body with screws provided, making sure that the spindle is positioned towards the hinge side. (See figure 1 and 2 above.) The power size (closing force) of the TS4000 is adjusted ap prox. 8 0°...
- Page 4 6 TS4000 only. If no latch action is required. Fit closer as described above. Separate the primary and secondary arms. Turn closing speed valve, located on the front of the body of the closer fully clockwise. This will decrease the closing speed to almost zero.
Need help?
Do you have a question about the TS4000 and is the answer not in the manual?
Questions and answers