Advertisement
This product should only be fitted by a qualified plumber to NVQ (National Vocational
Qualification) or SNVQ (Scottish National Vocational Qualification) Level 3. Should
the installation be completed by a non-qualified person then the guarantee may be
considered invalid.
For a claim made under our warranty written certification of your installers credentials
can be required. For further information or to find a qualified installer in your area
please visit the Institute of Plumbers website - www.iphe.org.uk
THE QUALIFICATIONS
At present, to be a plumber you need to follow the National Vocational Qualification
(NVQ) route (Scottish National Vocational Qualification - SNVQ - in Scotland). These
qualifications are made up of theory and practical work in the classroom/purpose built
training facility and work based experience with a working plumber. Colleges should
help students find a work placement, although many students organise it themselves.
The S/NVQ qualification works in levels. All recently qualified plumbers should hold
S/NVQ Level 2 as basic with Level 3 as the preferred level. Level 2 will give you the
foundation you need for a career in plumbing and teach you domestic plumbing to a
satisfactory level. Level 3 is more comprehensive and deals with domestic,
commercial and industrial plumbing along with aspects such as gas - if you want to one
day set up your own business, this is the level to reach. The Institute of Plumbing and
Heating Engineering, and the industry as a whole recommends that all plumbers reach
a minimum of Level 3.
Reaching Level 3 has other advantages. The Institute runs a Master Plumber
Certificate, which only those attaining Level 3 or equivalent can reach as long as they
have the relevant experience as well. Those with S/NVQ Level 3 can (once in
membership with the Institute for five years as a Member MIPHE) gain Engineering
Technician EngTech status with the Engineering Council (UK).
P5-208560F8-PR-E A/0
For any further information please contact
Crosswater on: 0845 873 8840
Or visit our web-site at www.crosswater.co.uk
The manufacturer reserves the right to make technical
modifications without prior notice.
BASIN 2 HOLE SET NO WASTE DECK MOUNTED
PRO125DNJ/C/V
INSTALLATION INSTRUCTIONS
Advertisement
Table of Contents
Related Manuals for Crosswater PRO125DNJ
Summary of Contents for Crosswater PRO125DNJ
- Page 1 Technician EngTech status with the Engineering Council (UK). INSTALLATION INSTRUCTIONS For any further information please contact Crosswater on: 0845 873 8840 Or visit our web-site at www.crosswater.co.uk The manufacturer reserves the right to make technical modifications without prior notice. P5-208560F8-PR-E A/0...
- Page 2 PRO125DNJ/C/V INTRODUCTION DIMENSIONS Please read these instructions carefully and keep in a safe place for future reference. General Installation Requirements. The installation must comply with regulations of the Local Water Authority as contained in their bylaws. All of the taps in this range are single flow (the hot and cold water mix in the body) and should therefore be supplied with hot and cold water at balanced pressures, both from the tank or both from the mains (via a combination boiler for example).
- Page 3 PRO125DNJ/C/V INSTALLATION INSTALLATION First shut off your water heating system then, with your mains stop cock closed, open the lowest hot and cold taps in the house and allow to run until the cold storage tank and pipes are empty (the hot water storage cylinder always remains full).
- Page 4 PRO125DNJ/C/V CLEANING MAINTENANCE The chrome and gold plate we use on our taps is very durable, nevertheless care should be taken when cleaning them. They should be cleaned only with warm soapy water followed by rinsing with clean water and drying with a soft cloth. All finishes are vulnerable...
Need help?
Do you have a question about the PRO125DNJ and is the answer not in the manual?
Questions and answers
Is it possible to get replacement internal filter units for the nozzle on my basin tap - PRO125DNJ/C/V
@Rosamond Conway