Page 2 (4) Great care has been taken in the preparation of this user’s manual; however, should you notice any questionable points, errors or omissions, please contact us. (5) Notwithstanding article (3), SANYO will not be responsible for any claims on loss of profit or other matters deemed to result from using the Projector.
Page 3: To The Owner
This symbol and recycle system are applied only to EU countries and not applied to the countries in the other area of the world. Your SANYO product is designed and manu- factured with high quality materials and components which can be recycled and reused.
Page 4: Safety Instructions
Safety Instructions All the safety and operating instructions should be read before the product is operated. Read all of the instructions given here and retain them for later use. Unplug this projector from AC power supply before cleaning. Do not use liquid or aerosol cleaners. Use a damp cloth for cleaning.
Page 5: Important Information
Important Information Air Circulation Openings in the cabinet are provided for ventilation. To ensure reliable operation of the product and to protect it from overheating, these openings must not be blocked or covered. CAUTION Hot air is from the exhaust vent. When using or installing the projector, the following precautions should be taken.
Page 6: Federal Communications Commission Notice
Model Number(s) : PDG-DXT10L Trade Name : Sanyo Responsible party : SANYO FISHER COMPANY Address : 21605 Plummer Street, Chatsworth, California 91311 U.S.A. Telephone No. : (818)998-7322 AC Power Cord Requirement The AC Power Cord supplied with this projector meets the requirement for use in the country you purchased it.
Page 7: Table Of Contents
Table of Contents 1. INTRODUCTION ...1 ’ ? ...1 S IN THE NTRODUCTION TO THE ROJECTOR Features you’ll enjoy:...2 AMES OF THE ROJECTOR Front-right View ...3 Top view ...4 Carrying the Projector ...5 Bottom view ...6 ...7 EATURES Lens Controls...7 OSD Controls and Status LEDs...8 ...10 ERMINAL...
Page 8 4. CONVENIENT FEATURES ...43 URNING FF THE MAGE AND ...43 REEZING A ICTURE DJUSTING THE OCUS Adjusting by Using the OSD Control Panel...44 ...45 HANGING Changing Lamp Mode by Using the Projector's OSD Control Panel ...45 Changing Lamp Mode by Using the Remote Control ...46 ...47 ETTING NFORMATION...
Page 9 Table of Contents 7. APPENDIX ...102 ...102 ROUBLESHOOTING Indicator Messages...102 Common Problems and Solutions ...104 Tips for Troubleshooting ...104 ...105 MAGE ROBLEMS Lamp Problems ...105 Remote Control Problems ...106 Audio Problems ...106 AVING THE ROJECTOR ERVICED 8. SPECIFICATIONS ...107 ...107 ROJECTOR PECIFICATIONS Optical Specifications ...107...
Page 10: Introduction
1. Introduction What’s in the Box? Carefully unpack the projector and check that the following items are included: PDG-DXT10L Projector CD-ROM (This User’s manual) Contact your dealer immediately if any items are missing, appear damaged, or if the unit does not work. CAUTION Avoid using the projector in dusty environments.
Page 11: Introduction To The Projector
1. Introduction Introduction to the Projector Features you’ll enjoy: DLP projector with high resolution The combination of BrilliantColor™ and a six-segment color wheel (optional) offer a more true color reproduction. Installation Flexibility This projector has many useful functions such as powered lens shifting, ceiling and rear projection, variety of extensive op- tional powered lens with bayonet mount with release button, etc.
Page 12: Part Names Of The Projector
Part Names of the Projector Front-right view ABEL IR receiver Lamp cover Lens control panel OSD control panel I/O connector panel Intake vent Speakers Height adjuster Lens Lens release button Anti-Theft screw Intake vent and front filter Important: Grill openings on the projector allow for good air circulation, which keeps the projector lamp cool. Do not obstruct any of the grill openings.
Page 13: Top View
1. Introduction Top view ABEL Lens control panel Right-hand speaker Lamp cover Exhaust vent OSD control panel Rear intake vent Left intake vent Left-hand speaker ESCRIPTION See Lens Controls Right-hand speaker Remove cover to replace lamp or color wheel Exhaust vent – do not obstruct See OSD Controls and Status LEDS Rear cooling intake –...
Page 14: Carrying The Projector
Carrying the Projector Always carry your projector by the handle. Before moving or carrying the projector, disconnect the power cable and any other cables that may be attached to it. When moving the projector or when the projector is not in use, cover the lens with the lens cap. To extend the projector handle, refer to the following guide.
Page 15: Bottom View
1. Introduction Bottom view ABEL Height adjusters Intake vent Front filter Ceiling support holes Security chain opening Rear filter Side filter CAUTION With ceiling installation, use approved mounting hardware & M4 screws; maximum depth of screw: 12 mm; dis- tance from ceiling/ wall: 20 cm (0.7 feet) for proper ventilation; distance from feet) front and back of the projector ESCRIPTION Adjust projection height...
Page 16: Top Features
Top Features Lens Controls ABEL ZOOM UP CURSOR RIGHT CURSOR DOWN CURSOR LEFT CURSOR FOCUS ESCRIPTION Increase/decrease projected image size Move image left, right, up, or down Focus the projected image 1. Introduction EE PAGE...
Page 17: Osd Controls And Status Leds
1. Introduction OSD Controls and Status LEDs ABEL MENU UP/ DOWN/ LEFT/ RIGHT BUTTONS RIGHT CURSOR/ VOLUME INCREASE CANCEL INPUT ON/STAND-BY LAMP 2 (LED) ESCRIPTION Open / Close the OSD Navigate and change settings in the OSD Increase volume Exit the On-Screen Display (OSD) Change or select the input device Turn the projector on or off (main power switch must be turned on first).
Page 18 ABEL LAMP 1 (LED) WARNING (LED) POWER (LED) AUTO PC ADJ. SELECT LEFT CURSOR/VOLUME DECREASE ESCRIPTION Green See Indicator Messages Flashing Green See Indicator Messages Orange Flashing Green Orange See Indicator Messages Flashing Optimize image size, position, and resolution Select or change settings in the OSD Decrease volume 1.
Page 19: Terminal Panel Features
1. Introduction Terminal Panel Features ABEL COMPUTER 3 IN AUDIO IN (COMPUTER 3) AUDIO OUT MONITOR OUT R/C JACK AUDIO IN (COMPUTER 2) AUDIO IN [L(MONO)/R] (COMPONENT) SERIAL PORT IN REMOTE IN ESCRIPTION Connect the DVI-D cable (not supplied) from a computer Connect the audio cable (not supplied) from the input device Audio loop-thru Connect to a monitor...
Page 20 ABEL SCREEN TRIGGER S-VIDEO POWER SWITCH AC IN AUDIO IN [L(MONO)/R] (VIDEO) VIDEO IN COMPONENT IN (Y, Cb/Pb, Cr/Pr) COMPUTER 2 IN (R/Cr, G/Y, B/Cb, H, V) COMPUTER 1 IN AUDIO IN (COMPUTER 1) SERVICE Note: To use this feature, you must turn on the Screen Trigger function on the OSD. Screen controllers are supplied and supported by screen manufacturers.
Page 21: Part Names Of The Remote Control
1. Introduction Part Names of the Remote Control ABEL STAND-BY LIGHT Illuminate the remote panel. MENU Open or close the on-Screen menu. CANCEL VOLUME - SELECT Executes a selected menu item VOLUME + LENS SHIFT Shift the lens up, down, right and left.
Page 22 1. Introduction Important: Avoid using the projector with bright fluorescent lighting turned on. Certain high-frequency fluorescent lights can disrupt remote control operation. 1. Be sure nothing obstructs the path between the remote control and the projector. If the path between re- mote and projector is obstructed, you can bounce the remote signal off certain reflective surfaces such as projector screens.
Page 23: Battery Installation
1. Introduction Battery Installation The Remote Control unit included with the projector does not contain batteries, though batteries are supplied as part of the complete package. To insert (or replace) the batteries, refer to the following guide. Remove the battery compartment cover by squeezing the locking catch and slid- ing the cover in the direction of the arrow.
Page 24: Operating Range For Wireless Remote Control
Operating Range for Wireless Remote Control Point the remote control toward the projector (to Infrared Remote Re- ceivers) when pressing the buttons. Maximum operating range for the remote control is about 16.4 feet (5 m) and 60 degrees in front and rear of the projector.
Page 25: Using The Remote Control In Wired Operation
1. Introduction Using the Remote Control in Wired Operation Connect the supplied remote cable to the R/C jack on the projector (see other end to the remote jack on the remote control (see item 1, Note: Connecting the remote cable to the R/C jack on the terminal panel will make the wireless operation unavail- able.
Page 26: Installation And Connections
2. Installation and Connections Setting Up the Screen and the Projector This section briefly describes how to set up your projector and how to connect video and audio sources. Your projector is simple to set up and use. But before you get started, you must first: Set up a screen and the projector.
Page 27: Selecting A Location
2. Installation and Connections Selecting a Location Locating the projector correctly ensures optimum performance and a longer parts life. Take note of the following when setting up the projector: The projector table or stand should be level and sturdy. Position the projector so that it is perpendicular to the screen. Ensure cables do not cause a trip hazard.
Page 28: Installing Or Removing The Optional Lens
Installing or Removing the Optional Lens Do not shake or place excessive pressure on the projector or the lens components as the projector and lens components contain precision parts. When shipping the projector with the optional lens, remove the optional lens before shipping the projec- tor.
Page 29: Installing The New Lens
2. Installation and Connections Pull out the existing lens slowly. CAUTION When Installing the lens into the projector, be sure to remove the lens cap from the back of the optional lens before installing the optional lens into the projector. Failure to do so will cause damage to the projec- tor.
Page 30: Installing The New Lens Using The Anti-Theft Screw
2. Installation and Connections Installing the New Lens Using the anti-theft screw Using the anti-theft screw to prevent theft of the lens. Tighten the supplied anti-theft screw on the front bottom.
Page 31: Throw Distance And Screen Size
2. Installation and Connections Throw Distance and Screen Size Example of LNS-S40: The further your projector is from the screen or wall, the larger the image. The minimum size the image can be is approxi- mately 40 inches (1 m) measured diagonally when the projector is roughly 65 inches (1.7 m) from the wall or screen. The largest the image can be is 500 inches (12.7 m) when the projector is about 843 inches (21.4 m) from the wall or screen.
Page 32 9.14 12.70 10.16 Ceiling installation must be done by a qualified professional. Contact your SANYO dealer for more information. It is not recommended you install the projector yourself. Only use the projector on a solid, level surface. Serious injury and damage can occur if the projector is dropped.
Page 33: Installing The Optional Color Wheel
2. Installation and Connections Installing the Optional Color Wheel The PDG-DXT10L projector comes with a four-segment color wheel installed. An additional six-segment color wheel is op- tional. To replace the color wheel (located under the lamp cover adjacent to lamp 1) refer to the following guide. Note: Wait until the lamp house and the color wheel cool off.
Page 34 Lift the color wheel in the direction shown Insert the six-segment color wheel Secure the retaining screws as shown. 2. Installation and Connections...
Page 35: Making Connections
2. Installation and Connections Align the lamp cover (A) with the arrow mark on the cabinet and slide it into place. Secure the captive screw (B). Storing Unused Color Wheel: Keep the unused color wheel in the zipper bag in which the 6-segment color wheel (not supplied) was packaged. This bag prevents dust from falling or collecting on the color wheel.
Page 36 2. Turn on the projector and select the chosen method of connection from the source menu before turning on the PC (see Selecting an Input Source on page 34). 3. Turn on the PC. Note: Failure to follow the above steps may not activate the digital output of the graphics card resulting in no pic- ture being displayed.
Page 37: Connecting An External Monitor
2. Installation and Connections Connecting an External Monitor Connect an external monitor to the projector through RGB out connections as shown below (see item 4, Terminal Panel Features on page 10)
Page 38: Connecting Your Dvd Player With Component Output
Connecting Your DVD Player with Component Output To connect a DVD Player to the projector, refer to the following guide. 1. Connect the DVD Player to the projector as shown below before turning on the Player or the projector. 2. Turn on the projector and select Component from the source menu before turning on the DVD Player (see Selecting an Input Source on page 34).
Page 39: Connecting Your Vcr Or Laser Disc Player
2. Installation and Connections Connecting Your VCR or Laser Disc Player To connect your VCR or Laser Disc Player, refer to the following diagram. Note: Refer to your VCR or laser disc player user’s manual for more information about your device’s requirements. Images may not be displayed correctly when using an S-Video or Video connection to fast-forward or fast- rewind scanning.
Page 40: Connecting The Supplied Power Cable
Connecting the Supplied Power Cable This projector uses nominal input voltages of 100–120V or 200–240V AC and it automatically selects the correct input volt- age. It is designed to work with single-phase power systems having a grounded neutral conductor. To reduce the risk of electrical shock, do not plug into any other type of power system.
Page 41: Projecting An Image (Basic Operation)
3. Projecting an Image (Basic Operation) Turning on the Projector Once the projector is correctly located and the power cable and other connections are in place, it is important that the pro- jector is powered on correctly in order to avoid damage to components and unnecessary wear and tear. Refer to the following guide to power on the projector.
Page 42: Note On Startup Screen (Menu Language Select Screen)
Note on Startup Screen (Menu Language Select screen) In the first instance of powering on the projector, the language menu is displayed to select the default language. Select the required default language using the press Select. Note: The language select screen only appears on the first instance of power on. All subsequent operations as- sume the selected default language.
Page 43: Selecting An Input Source
3. Projecting an Image (Basic Operation) Selecting an Input Source The Input Source can be selected from the projector's control panel or from the remote control unit. Refer to the following guide to select the Input Source. Press Menu on the OSD control panel or on the remote control unit to display the Main Menu.
Page 44: Adjusting The Picture Position And Picture Size
Adjusting the Picture Position and Picture Size The Picture Position and Picture Size can be adjusted manually from the lens control panel or from the remote control unit. Refer to the following guides to adjust Picture Position manually. Adjusting Picture Position Manually Press the Select keypad in any direction to bring up the Lens Shift window.
Page 45: Lens Shift Adjustable Range
3. Projecting an Image (Basic Operation) The Screen window is displayed. Select the desired picture size using press Select. When finished, press Cancel to return to the projected image. Lens Shift Adjustable Range The adjustable range for lens shift is tabulated below and subject to the conditions listed. Note: The drawings below apply to the standard lens (LNS-S40) only.
Page 46: From The Remote Control Unit
From the Remote Control Unit Press the Lens Shift button to bring up the Lens Shift window. Press the directional keys as required to shift the image. Releasing the directional arrow will re-center the cursor. To alter the picture size, press the Screen button to display the Screen window.
Page 47: Adjusting The Projector Level
3. Projecting an Image (Basic Operation) Adjusting the Projector Level To raise the level of the projector, twist the adjust- ers clockwise. To lower the level of the projector, lift the projector and twist the adjusters counter clockwise.
Page 48: Optimizing An Rgb Image Automatically
3. Projecting an Image (Basic Operation) Optimizing an RGB Image Automatically Adjusting the Image Using AUTO PC ADJ. To optimize an RGB image automatically refer to the following guide. Press the AUTO PC button on the remote control (see item 17, Part Names of the Remote Control on page 12) or the AUTO PC ADJ.
Page 49: Adjusting Volume Up And Down
3. Projecting an Image (Basic Operation) Adjusting Volume Up and Down The volume can be adjusted from the OSD Control Panel or with the Remote Control unit. Refer to the following as a guide. Press the Volume +/- buttons on the remote control or the buttons on the OSD con- trol panel.
Page 50: Turning Off The Projector
Turning off the Projector Once the projector is no longer required, it is important to shut it down correctly to avoid damage or unnecessary wear and tear to the projector. Do not unplug the power cable from the wall outlet or projector when the projector is powered on. Doing so can cause damage to the AC IN connector of the projector and (or) the prong plug of the CAUTION power cable.
Page 51: About Direct Power Off
3. Projecting an Image (Basic Operation) About Direct Power Off The projector has a feature called "Direct Power Off". This feature allows the projector to be turned off (even when projecting an image) using a power strip equipped with a switch and a breaker. Note: Before using Direct Power Off, be sure to allow at least 20 minutes immediately after turning on the projector and starting to display an image.
Page 52: Convenient Features
4. Convenient Features Turning Off the Image and Sound The projected image and sound can be turned off for short periods of time with the remote control. This feature is useful for breaking up presentations or for other brief interruptions in projections. To turn off the picture and image, refer to the following guide 1.
Page 53: Adjusting The Focus/Zoom Manually
4. Convenient Features Adjusting the Focus/Zoom Manually The focus and zoom can be adjusted manually from the projector focus/zoom panel or from the remote control unit. Refer to the following guides to adjust the focus and zoom manually. Adjusting by Using the OSD Control Panel Press the Focus or Zoom button on the projector panel to display the appropriate window.
Page 54: Changing Lamp Mode
Changing Lamp Mode The projector has two lamp modes available, Normal and Eco. The Normal mode is used for everyday standard projec- tion, whereas the Eco mode is used for saving power and lamp life. To change the Lamp Mode, refer to the following guides.
Page 55: Changing Lamp Mode By Using The Remote Control
4. Convenient Features Changing Lamp Mode by Using the Remote Control Press the Lamp control button on the remote control to ac- cess the Lamp control menu. From the Lamp control window, select Normal or Eco us- or . Move the cursor to OK and press Select. Note: When the projector is in Eco mode, brightness may be affected.
Page 56: Getting Information
Getting Information The Information screen provides details on the life of consumable items within the projector as well as other information such as software version. To access the Information screen, refer to the following guide. Press Menu on the projector's OSD control panel or remote control to display the Main Menu.
Page 57: Adjusting Position/Total Dots/Fine Sync
4. Convenient Features Adjusting Position/Total Dots/Fine Sync The Position/Total dots/Fine sync and Keystone Correction can be adjusted manually from the projector's control panel or from the remote control unit. Refer to the following guides to adjust the Keystone Distortion manually. Adjusting Position/Total Dots/Fine Sync by using the OSD Control Panel Press the Menu button to display the Main menu.
Page 58: Correcting Keystone By Using The Remote Control
Correcting Keystone by Using the Remote Control IMPORTANT: When adjusting the keystone, place the projector in the following position. Horizontal: set to the lens center Vertical: set to the maximum top Press the Keystone but- ton to display the Keystone window. Adjust the Horizontal and Vertical sliding bars using the select...
Page 59 4. Convenient Features Note: Holding down the Keystone button for 2 seconds resets the default keystone values. DJUSTMENT Keystone The following are conditions under which the maximum angle is achieved: When the standard lens (LNS-S40) is used When the lens shift is set to H for center and V for 0.5 shift. When the lens shift is used and yet you do not get the above-mentioned condition (H for center and V for 0.5 shift), you cannot adjust the lens shift correctly.
Page 60: Preventing The Unauthorized Use Of The Projector
Preventing the Unauthorized Use of the Projector The projector has an built-in security feature to lock the OSD control panels and deny remote control operation. The secu- rity feature has no default keyword; in the first instance of enabling the security feature, the user must define a keyword. Locking the Projector To setup the security keyword, refer to the following guide.
Page 61 4. Convenient Features The PIN code window is displayed. Enter a PIN code between 4 and 10 characters using . The PIN code characters change to “ * ”. Press Select. Once a successful PIN code is entered, a confirmation screen is displayed. Enter the same password as the previous step and write it down for later reference.
Page 62: Unlocking The Projector
Unlocking the Projector To unlock the projector, refer to the following guide. When the projector is locked, either by re- quest during operation or at start up, the locked message is displayed. To unlock the projector, press Menu on the control panel or remote control.
Page 63: Using The Physical Lock
4. Convenient Features Using the Physical Lock For security and authorized usage, the projector comes with two types of security features, the Kensington Lock and the Security Chain Lock. Using the Kensington Lock If you are concerned about security, attach the projector to a permanent object with the Kensington slot and a security cable.
Page 64: Using On-Screen Display
5. Using On-Screen Display Using the Menus The projector has an On-Screen Display (OSD) that lets you make image adjustments and change various settings. Navigating the OSD You can use the remote control or the buttons on the top of the projector to navigate and make changes to the OSD. The following illustration shows the corresponding buttons on the remote control and on the projector.
Page 65 5. Using On-Screen Display Press the cursor move through secondary menus. Press to select menu items and to change values for settings. Press Select to confirm the new setting. Press Cancel to close the OSD or leave a submenu. button to...
Page 66: Menu Tree
Menu Tree The gray shaded areas indicate factory default settings. Input Computer 1, Computer 2, Computer 3, Component, Video, S-Video Test pattern Adjust Image Image select Detail setting Contrast Brightness Sharpness Color Tint Reset Image Screen options Overscan PC Adj. Horizontal Vertical Total dots...
Page 67 5. Using On-Screen Display Installation Ceiling & Rear Communication speed Menu color select Display time Background PIN code lock Key lock Dynamic black RC sensor Network setting Standby mode PC control Option On start Power management Screen trigger Fan control Default input select Color system Video...
Page 68: Menu Elements
Menu Elements Some menus and windows contain large amounts of information in a small area. Refer to the following guide to navigate through options more easily. Menu windows or dialog windows typically contain the following elements: ABEL Title Highlight Menu type Radio button Slide bar Exit...
Page 69: Source Menu Descriptions And Functions
5. Using On-Screen Display Source Menu Descriptions and Functions The Source menu displays all supported image sources. Select the required source from the menu using Select the source connected to the Computer 1 input Computer 1 (see Connecting Your PC or Macintosh Computer on page 26). Select the source connected to the Computer 2 input Computer 2 (see Connecting Your PC or Macintosh Computer on page 26).
Page 70: Adjust Menu Descriptions And Functions
Adjust Menu Descriptions and Functions The Adjust menu contains overall projector settings for image output such as sharpness, overscan and color matrix. Three tabs are accessible through the Adjust menu, Picture, Image Options and Video. Image menu The image menu is used to alter picture settings and can be accessed from the Adjust menu. The following table lists all functions with a description and the default setting.
Page 71: Image Options Menu
5. Using On-Screen Display Image options menu The Image Options menu is used to configure image options such as screen positioning and aspect ratio. Access the im- age options menu in the Adjust menu. The following table lists all functions with a description and the default setting. Screen Select Screen using Overscan...
Page 72 Screen The screen option allows for the adjustment of the aspect ratio to alter the appearance or ratio of the projected image. 4:3 – Standard TV screen (4:3), proportionally four units wide for every three units high, no matter the size of the screen. 16:9 –...
Page 73: Video Menu
5. Using On-Screen Display Video menu The Video menu is used to configure image options such as film. Access the Video menu in the Adjust menu. The following table lists all functions with a description and the default setting. A detailed description follows the table. Noise reduction Select Noise reduction mode (see page 65).
Page 74 Noise reduction Select the level of noise reduction required. Range: Off, Low, Mid, High. 3D Y/C separation 3D Y/C Separation separates composite signal to Y (brightness) signal and C (color) signal, and can help to produce clearer and sharper images without overlapping colors (rainbow effect). Set 3D Y/C Separation On or Off.
Page 75 5. Using On-Screen Display Color matrix Color Matrices define the amount of the three-color components R (red), G (green), and B (blue) in a single point in color space. Select from the following: Auto – Auto selects the color matrix. RGB –...
Page 76: Detail Settings Menu Descriptions And Functions
Detail Settings Menu Descriptions and Functions The Detail settings menu contains basic and advanced color adjustment options such as gamma correction, color contrast and color correction. Basic The Basic tab contains general Detail Settings such as gamma correction and color temperature. Access to the General tab is through the Detail Settings menu.
Page 77 5. Using On-Screen Display Reference The Reference mode allows the projector to differentiate between source materials for example movies, PC images or video stills. Select from the following: High-bright – Select for use in a brightly lit room. Presentation – Select if the projector is to be used for presentation purposes. Video –...
Page 78: White Balance
White balance White Balance allows the projector to compensate for different colors of light being emitted by different light sources. The following table lists all functions with a brief description. Set the value to compensate for red light sources. Green Set the value to compensate for green light sources.
Page 79: Color Correction
5. Using On-Screen Display Color correction The Color correction tab enables the adjustment of color values in an image to remove unwanted effects, improve color, characteristics or add more of a particular color. The following table lists all functions with a brief description. Increase or decrease the amount of red in the projected output using Green Increase or decrease the amount of green in the projected output using...
Page 80: Setting Menu Descriptions And Functions
Setting Menu Descriptions and Functions The Setup menus contain the most often used settings during installation and options to customize the general output of the projector. Three tabs are accessible through the Setup menu, general, installation and option. Basic The Basic tab contains general setup options such as lamp mode and OSD language settings and can be accessed with the projector control panel or with the remote control unit.
Page 81 5. Using On-Screen Display Keystone The keystone trapezoid can be adjusted by selecting this option. Select Horizontal or Vertical using IMPORTANT: When adjusting the keystone, place the projector in the following position. Horizontal: set to the lens center Vertical: set to the maximum top Lamp control Select Normal or Eco from the lamp mode window.
Page 82 Lamp interval The period of time for regulating lamp usage when not in dual lamp mode. Select from the following: Off, 1 week, 4 weeks and 2000H Simple menu Select the Simple menu to display. Set Simple menu On or Off. 5.
Page 83 5. Using On-Screen Display Language Select the OSD language to be used. Select from the following: English German French Italian Spanish Swedish Japanese Simplified Chinese...
Page 84: Installation
Installation The Installation tab contains menu options for various setup conditions such as orientation and remote sensor mode and is accessed through the Setup menu. The following table lists all functions with a brief description. Ceiling & Rear Communication speed Menu color select Display time Background...
Page 85 5. Using On-Screen Display Key lock DynamicBlack Set RC sensor fields. RC sensor Range: Both, Front, Back Network setting Opens Network preferences tab (see Network setting on page 80). Select Standby mode. Standby mode Range: Normal and Power-saving PC control Ceiling &...
Page 86 Communication speed Select communication speed to set the baud rate of the connection. Note: Longer cable connections may require lower settings. Select from the following options: 4800bps 9600bps 19200bps 38400bps Note: In the Network mode, Communication Speed function is not available. Menu color select Select color mode to set the menu color.
Page 87 5. Using On-Screen Display Monochrome Display time Sets the amount of time a menu is displayed. Select from the following: Manual – Menus stay on screen until the Menu button is pressed again. Auto 5 secs—Menu is displayed for 5 seconds. Auto 15 secs –...
Page 88 PIN Code Lock Preventing the Unauthorized Use of the Projector on page Key lock Turn On/Off the Key Lock function for cabinet buttons. Note: This Control Panel Lock does not affect the remote control functions. When the control panel is locked, pressing and holding the Cancel button on the projector cabinet for about 10 seconds.
Page 89 5. Using On-Screen Display Network Setting See Network setting on page 82. Standby mode There are two standby modes available: Normal and Power-saving. Power-saving mode allows you to put the projector in the standby condition to consume less power than Normal. Note: Be sure to connect the projector and computer while the projector is in standby mode and before turning on the computer.
Page 90 PC control This function enables you to select the path for PC control (see on page 115). Note: In the Network mode, Communication Speed function is not available. Select from the following: PC control Network 5. Using On-Screen Display PC Control Codes and Cable Connections...
Page 91: Network Setting
5. Using On-Screen Display Network setting The Network setting tab is accessed by using the Setup/Installation tab and contains the general LAN settings. The following table lists all functions with a description and the default setting. DHCP Select either a static IP or DHCP IP setting by selecting the appropriate radio button. IP address Displays the IP address.
Page 92: Option
Option The Option tab contains miscellaneous setup menu settings such as Power Management and Default Input Select and can be accessed by using the Setting Menu. The following table lists all functions with a description and the default setting. Set this item on to enable the projector to power up when AC plug in. On start Range: On or Off Select the amount of time the projector remains idle before powering down.
Page 93 5. Using On-Screen Display This option switches remote control codes. Remote control Range: Code 1, Code 2, Code 3, Code 4, Code 5, Code 6, Code 7, Code 8 This option turns on or off messages. Message Range: Off or On Set this item to on to have the projector display a message when the air filter needs servicing.
Page 94 Select from the following: 5 minutes 10 minutes 20 minutes 30 minutes Screen trigger Set Screen trigger to On to enable the projector to automatically lower the projection screen when powering on. When powering off, Screen trigger stops sending a low voltage trigger to the screen controller and the screen goes up. Fan control Fan control is used to set the speed of the internal cooling fan.
Page 95 5. Using On-Screen Display Default input select The Default input is the image source that the projector will search for automatically on startup. Last – Uses the most recently used image source. Auto – Auto detects the default image source. Computer1/2/3 –...
Page 96 Remote control This projector has eight different remote control codes; the factory set normal mode (Code 1) and the other seven codes (Code 2 to Code 8). This switching function prevents remote control operation mixture (jam) when operating several projec- tors or video equipment together.
Page 97 5. Using On-Screen Display Filter warning Set Filter warning to have the projector display a message when the air filter needs servicing. The message below shows when this function is activated. Search mode This feature sets the Auto Adjust mode so that the RGB image can be automatically or manually adjusted for noise and stability.
Page 98: Information Menu Descriptions And Functions
Information Menu Descriptions and Functions The information menu provides only screens for the quick access of menus. The Information menu contains four distinct tabs. Usage time The Usage Time tab displays information about lamp usage and remaining lamp life. The following table lists all items with a description. Lamp1 Life remaining Displays the Lamp1 life remaining as a percentage.
Page 99: Input
5. Using On-Screen Display Input The Input tab displays various source and frequency values at a glance. The following table lists all items with a description. Displays the Input Terminal that is presently being used Input name (see Default input select on page 86). Displays the Source name of the signal presently being used Signal (see Option on page 83).
Page 100: Network
5. Using On-Screen Display Network The Network tab displays LAN settings as previously defined (see Network setting on page 82).
Page 101: Version
5. Using On-Screen Display Version The Version tab displays all the version and product details of the projector and associated software (for display only). The following table lists all items with a description. Model name Displays Product ID. Serial number Displays projector Serial number.
Page 102: Reset Menu Descriptions And Functions
Reset Menu Descriptions and Functions Occasionally, circumstances may require that factory defaults be reset, for demonstration purposes for example, or when components are replaced. The Reset menu contains options for returning settings to the factory default and is accessed by using the Main menu. The following table lists all items with a description.
Page 103: Maintenance
6. Maintenance Cleaning the projector Cleaning the Cabinet Refer to the following guide to clean the projector cabinet. Wipe off dust with a clean dampened cloth. Moisten the cloth with warm water and mild detergent and wipe the cabinet. Rinse all detergent from the cloth and wipe the projector again. CAUTION To prevent discoloration or fading of the case, do not use abrasive alcohol-based cleaners.
Page 104: Cleaning The Filters
Cleaning the Filters The projector uses three filters to keep the fans free of dust and other particles, and should be cleaned every 500 hours of operation. In dusty environments, it is recommended to clean the filters more frequently. If the filter is dirty or clogged, your projector may overheat.
Page 105 6. Maintenance The rear filter can be accessed as shown. Once the filters are cleaned, please reset the filter hours by using the Clear filter time option in the Reset Menu Descriptions and Functions on page 93. Note: Using the projector without the air filter fitted inside, dirt and dust are sucked into the projector, causing fail- ure.
Page 106: Replacing Consumable Parts
Replacing Consumable Parts During the course of normal usage, consumable parts become worn out resulting in reduced performance. The following guides detail how to replace the various consumable parts within the projector quickly and safely. Before replacing any of the parts, please take note of the following: Ensure that the projector is turned off and disconnected from the power supply.
Page 107 6. Maintenance Insert replacement foam and press down firmly. Replace the filter covers by pushing gently in the direction shown. Once the filters are replaced, please reset the filter hours by using the Clear filter time option in the Reset Menu Descriptions and Functions on page 93.
Page 108: Replacing The Lamps
Replacing the Lamps When a lamp reaches the end of it’s usable life, the following message is displayed. Replace the lamp. The projection lamps should be replaced when they burn out. They should only be replaced with a certified replacement part, contact your local dealer if unsure.
Page 109 6. Maintenance Check the lamp number to be replaced by using Information Menu. Turn off the projector and disconnect the AC plug. Allow the projector to cool for at least 60 minutes. Loosen the screw on the lamp cover (A), and remove the lamp cover as shown (B).
Page 110: Resetting The Lamp Time Counter
Lamp hours to zero. Ordering a Replacement Lamp Replacement lamp can be ordered through your dealer. When ordering, give the following information to the dealer. Model No. of your projector: PDG-DXT10L, PDG-DXT10KL Replacement Lamp Type No: POA-LMP117 (Service Parts No. 610 335 8406) button to move to 6.
Page 111: Appendix
7. Appendix Troubleshooting Indicator Messages Several indicator messages are used by the projector to alert users of problems with setup or internal parts. The LEDs on the top surface of the projector show the status of the WARNING and lamp 1/2 as well as the general working order of the projector through the WARNING LED (see OSD Controls and Status LEDS on page describe the various states of the 4 LEDs.
Page 112 The LAMP LEDs LED C ROJECTOR TATUS Lamp off End of the lamp life Red blink Red 1 time blink (re- No lamp peatedly) Red 6 times blink ( Lamp ERROR peatedly) Cooling lamp Orange blink Re-light up sequence Green blink Lamp life over Red on Eco mode...
Page 113: Common Problems And Solutions
7. Appendix Common Problems and Solutions These guidelines provide tips to deal with problems you may encounter while using the projector. If the problem remains unsolved, contact your dealer for assistance. Often the problem is something as simple as a loose connection. Check the following before proceeding to the problem- specific solutions.
Page 114: Image Problems
Image Problems Problem: No image appears on the screen 1. Verify the settings on your notebook or desktop PC. 2. Turn off all equipment and power up again in the correct order. Problem: The image is blurred 1. Adjust the Focus on the projector. 2.
Page 115: Remote Control Problems
7. Appendix Remote Control Problems Problem: The projector does not respond to the remote control 1. Direct the remote control towards remote sensor on the projector. 2. Ensure the path between remote and sensor is not obstructed. 3. Turn off any fluorescent lights in the room. 4.
Page 116: Specifications
8. Specifications Projector Specifications This section provides technical information about the projector's performance. Optical Specifications Projection system Resolution Lamp Image size (diagonal) Lens options Lens shift *Effective pixels are more than 99.99% ® Single DLP chip, 4 segment color wheel 1024 x 768 pixels* (up to UXGA @ 60 Hz, up to SXGA+ @ 60 Hz on DVI-D) 260 W AC (230 W in Eco mode), Dual lamp system 50"...
Page 117: Electrical Specifications
8. Specifications Electrical Specifications 1 Analog RGB (Mini D-Sub 15P), 1 Analog RGB R/Cr, G/Y, B/Cb, H, V (BNC x 5), 1 Digital RGB (DVI-D 24P), 1 Component Y, Cb/Pb, Cr/Pr Inputs (RCA x 3), 1 Component (Mini D-Sub 15P) shared with COMPUTER 1 IN, 1 S-Video (Mini DIN 4P), 1 Video, 3 Stereo Mini Audio, 2 (L/R) RCA Audio, 1 Remote Control (Stereo Mini) Outputs...
Page 118: Mechanical Specifications
655W in Dual Lamp Normal mode / 580W in Dual Lamp Eco mode 350W in Single Lamp Normal mode / 315W in Single Lamp Eco mode Power Consumption < 30W in Standby mode Normal < 5W in Standby mode Power saving Mechanical Specifications 19.9"...
Page 119: Optional Parts
8. Specifications Optional Parts The parts listed below are optionally available. When ordering those parts, specify the item name and Model No. to the sales dealer. Standard Zoom Lens Long Zoom Lens Ultra Long Zoom Lens Short Zoom Lens Fixed Short Zoom Lens Six-segment Color Wheel Wired Remote Cable (30m) : LNS-S40...
Page 120: Cabinet Dimensions
8. Specifications Cabinet Dimensions...
Page 121: Pin Assignments Of Mini D-Sub 15 Pin Input Connector
8. Specifications Pin Assignments of Mini D-Sub 15 Pin Input Connector Signal Levels Video signal: 0.7Vp-p (Analog) Sync signal: TTL level RGB S UMBER IGNAL Green or Sync on Green Blue Ground Ground Red Ground Green Ground Blue Ground No Connection Sync Signal Ground No Connection Bi-directional DATA (SDA)
Page 122: Compatible Input Signal List
Compatible Input Signal List The following table shows compatible signal types, their resolution and frequency refresh rates. Horizontal: 15kHz, 31kHz to 90 kHz Vertical: 50 Hz to 85 Hz IGNAL NTSC – – PAL60 – SECAM – VESA VESA VESA VESA VESA VESA...
Page 123 8. Specifications IGNAL VESA VESA VESA HDTV (1080i)(1125i) – HDTV (1080i)(1125i) – HDTV (720p)(750p) – HDTV (720p) – SDTV(576p)(625p) – SDTV (480p)(525p) – DVD YCbCr – DVD YCbCr – Note: Images above flagged with "D" are supported by digital signal. An image with higher or lower resolution than the projector’s native resolution (1024 x 768) will be com- pressed.
Page 124: Pc Control Codes And Cable Connections
PC Control Codes and Cable Connections This projector provides a function to control and monitor the projector's operations by using the RS-232C serial port. Connect a RS-232C serial cross cable to SERIAL PORT IN on the projector and serial port on the PC. Launch a communication software provided with PC and setup the communication condi- tion as follows:...
Page 125: Status Read Command Table
8. Specifications Status Read Command Table OMMAND Status Read Temperature Read PC Control Connector (DIN-9P) Note: 1. Pin 1, 4, 6 and 9 are not used. 2. Jumper “Request to Send” and “Clear to Send” together on both ends of the cable to simplify the cable connection.
Page 126: Screen Trigger
Screen Trigger When the projector is powered ON the screen trigger output sends a low voltage trigger to the screen controller and the screen will go down. When the projector is powered OFF the screen trigger stops sending a low voltage trigger to the screen controller and the screen will go up.
Page 127: Operation Using Http Browser
8. Specifications Operation Using HTTP Browser Overview The use of HTTP server functions will allow control of the projector from a web browser without the installation of special software. Please be sure to use “Microsoft Internet Explorer 4.x” or a higher version for the web browser. (This device uses “JavaScript”...
Page 128: Configuring Network Settings
Configuring Network Settings The Network Settings screen is displayed as follows: http:// <the projector's IP address> /lanconf.html Domain Host Name: Type in a hostname. Up to 60 alphanumeric characters can be used. Domain Name: Type in domain name of the network connected to the projector. Up to 60 alphanumeric characters can be used. Apply: Click to reflect the entries.
Page 129 8. Specifications Test Mail Send a test mail to check if your settings are correct. Click to “Execute” to enable this feature. Test Mail Status Button: Click to display the test result. Sample of a message sent from the projector: Projector Name: X X X X Lamp 1 or 2 Hours Used: xxxx [H] The lamp is at the end of its usable life.
Page 130: Structure Of The Http Server
Structure of the HTTP Server Once the projector is connected to a network and configured correctly, the following screen is displayed through the web browser. http:// <the projector's IP address> /index.html UNCTION Power Panel Volume Panel – Increases the volume adjustment value –...
Page 131 8. Specifications UNCTION Input Select Panel Computer1 – Switches to the COMPUTER 1 IN connector Computer2 – Switches to the COMPUTER 2 IN connector Computer3 – Switches to the COMPUTER 3 IN connector Component – Switches to the COMPONENT IN connectors Video –...
Page 132: 15 Pin Gpio Control
15 Pin GPIO Control Type: 15Pin D-SUB black female type 4, 8, 12, 11 Note: The term “SHORT” is defined as having a connection to pin 15. HORT SHORT OPEN SHORT OPEN SHORT OPEN SHORT OPEN OPEN OPEN OPEN OPEN OPEN OPEN OPEN...
Page 133: Troubleshooting Check List
9. Troubleshooting Check List Before contacting your dealer or service personnel, check the following list to be sure repairs are needed also by referring to the Troubleshooting section on page more efficiently. Frequency of Occurrence always Power No power (POWER indicator does not light green) See also “Status Indica- tor (WARNING)”.
Page 134 Sync on Green WARNING Indicator: Steady light Orange Green Flashing light [ ] cycles Remote control model number: Signal cable SANYO standard or other manufacturer’s cable? Model number: Length: Distribution amplifier Model number: Switcher Model number: Adapter Model number: Installation environment...
Page 135 KT3AL SANYO Electric Co., Ltd.

This manual is also suitable for:

Pdg-dxt10l

Sanyo PDG-DXT10KL User Manual

1 Introduction

2 Installation and Connections

3 Projecting an Image (Basic Operation)

4 Convenient Features

5 Using On-Screen Display

6 Maintenance

7 Appendix

8 Specifications

9 Troubleshooting Check List

Quick Links

Troubleshooting

Related Manuals for Sanyo PDG-DXT10KL

Summary of Contents for Sanyo PDG-DXT10KL

This manual is also suitable for:

Table of Contents