Simplex 4100ES Operating Instructions Manual

UL, ULC, CSFM Listed; FM Approved;
MEA (NYC) Acceptance*
Features
Remote Annunciator Panels provide fire alarm
control panel status information at locations
distant from the fire alarm control panel
Typical functions include:
 Remote status LED indicators and dedicated switch
input controls located on LED/switch modules
 Remote status LED indicator modules with 8 red or
16 (8 red/8 yellow) LEDs that are pluggable to allow
color selection (yellow, green, or red LEDs are
ordered separately)
 Remote microphone and operator interface for access
to the emergency voice/alarm communications system
 Remote master telephone for communicating to the
firefighter telephone system
 Also available with InfoAlarm Command Center
expanded content user interface (refer to page 5 and to
data sheet S4100-0045 for additional information)
Additional optional modules include:
 Remote Command Center module for LCD status
readout and keyswitch controlled functions
 24 Point I/O module
 RS-232 ports for remote printer or terminal
connections
 Power supplies with battery charger for annunciator
 Panel mounted printer for system status recording
Wiring requirements:
 RUI or RUI+ (remote unit interface) supervised
communications from the host fire alarm control
panel provide Style 4 or Style 7 SLC (signaling line
circuit) connections
 Microphone and telephone circuits require their own
dedicated wiring
Listed to:
 UL Std. 864, Fire Detection and Control (UOJZ), and
Smoke Control Service (UUKL)
 UL Std. 2017, Process Management Equipment
(QVAX)
 UL Std. 1076, Proprietary Alarm Units-Burglar
(APOU)
 UL Std. 1730, Smoke Detector Monitor (UULH)
 ULC Std. S527-99
* See page 4 for additional listing details. This product has been approved by the California
State Fire Marshal (CSFM) pursuant to Section 13144.1 of the California Health and
Safety Code. See CSFM Listing 7165-0026:0251 for allowable values and/or conditions
concerning material presented in this document. Additional listings may be applicable;
contact your local Simplex ® product supplier for the latest status. Listings and approvals
under Simplex Time Recorder Co. are the property of Tyco Fire Protection Products.
Fire Control Panels
Remote Annunciator Panels
REMOTE COMMAND CENTER
FIRE PRIORITY 2 SYSTEM SYSTEM POWER ALARM
DISPLAY
SILENCED TIME
ALARM ALARM SUPERVISORY TROUBLE ON
ALARM ALARM SUPV TBL ALARM SYSTEM
ACK ACK ACK ACK SILENCE RESET
Emergency Operating Instructions
Alarm or Warning Condition How to Silence Building Signals
System indicator flashing. Tone On. Press Alarm Silence.
How to Acknowledge / View Events How to Reset System
Press ACK located under flashing indicator. Press System Reset.
Repeat operation until all events are acknowledged. Press Ack to silence tone device.
Local tone will silence.
On On
Off Off
Auto Auto
On On
Off Off
Auto Auto
On On
Off Off
Auto Auto
On On
Off Off
Auto Auto
4100ES Remote Annunciator in a Three Bay Cabinet with
Audio Operator Modules; Remote Command Center (left)
and with an InfoAlarm Command Center (right)
Introduction
Remote Annunciator Panels are dedicated purpose
transponders that support fire alarm system status
information. Typical use is when the host fire alarm
control panel is located away from the area where those
responding to a fire situation need status information.
Status and Control. Controls are suitable for
firefighter or other fire brigade responders to access
particular information and for system control. When
equipped with a remote microphone and emergency
voice/alarm communications system control, an
authorized user can take command of the system and
either play selected pre-recorded messages or select
specific tones, or initiate live broadcast information either
globally into the system, or to selected areas.
Remote Master Firefighter Phone. When equipped
with a remote master phone, the authorized user can
connect to remote phone call-in requests and allow callers
to be connected to each other. Although intended for use
in assisting fire responders, these system are also helpful
during system setup and test.
ZONE A B C D E F SIG AUX G H I
Page Up 1 2 3
J K L M N O P Q R
FB IO IDNet
Previous 4 5 6
S T U V W X Y Z /
P A L
Next 7 8 9
'SP' ( ) , # :
NET ADDR
Page Dn 0 C/Exit
Menu Enter
Fire Priority 2 System System Alarm AC
Alarm Alarm Supervisory Trouble Silenced Power
Fire Alarm Priority 2 Supv Trouble Alarm System
Ack Ack Ack Ack Silence Reset
ALARMS WARNINGS
Emergency Operating Instructions
How to Acknowledge / View Events Alarm or Warning Condition How to Reset System
Press ACK located under flashing indicator. System indicator flashing. Tone On. Press System Reset.
Repeat operation until all events are acknowledged. Press Ack to silence tone device.
How to Silence Building Signals
Local tone will silence. Press Alarm Silence.
On On
Off Off
Auto Auto
On On
Off Off
Auto Auto
On On
Off Off
Auto Auto
On On
Off Off
Auto Auto
S4100-0038-14 5/2018