tado° Smart Thermostat Installer's Manual
  1. Manuals
  2. Brands
  3. tado° Manuals
  4. Thermostat
  5. Smart Thermostat
  6. Installer's manual

tado° Smart Thermostat Installer's Manual

Low voltage digital installations
Hide thumbs Also See for Smart Thermostat:

Advertisement

Table of Contents

United Kingdom
Part 2 of 2
Smart Thermostat
Low Voltage Digital Installations
Guide for Professional Installers
If you are not a professional installer and want to install tado°
yourself, get step-by-step instructions at tado.com/start

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Smart Thermostat and is the answer not in the manual?

Questions and answers

Related Manuals for tado° Smart Thermostat

Summary of Contents for tado° Smart Thermostat

  • Page 1 United Kingdom Part 2 of 2 Smart Thermostat Low Voltage Digital Installations Guide for Professional Installers If you are not a professional installer and want to install tado° yourself, get step-by-step instructions at tado.com/start...
  • Page 2 POLARITY-PROTECTED WIRING For all two-wire digital installations the wires connected to + and - on tado° can be interchanged CAUTION Make sure to turn the power off before you start 10/2018...
  • Page 3 Optional Accessory tado° Trim Plate Use the behind the Smart Thermostat or Extension Kit if needed. This can be obtained separately at tado.com/trim-plate...
  • Page 4 1. Wiring: OpenTherm Wired Setup: Smart Thermostat is wired directly to the boiler Smart Thermostat Wireless Setup: Smart Thermostat installed wirelessly with receiver Smart Thermostat & Extension Kit...
  • Page 5 Boiler Smart Thermostat MAX 36 V DC Boiler Extension Kit The Extension Kit requires a separate 230 V power supply at N and L for OpenTherm installations...
  • Page 6 2. Connect Internet Bridge to Router If no free USB jack available - plug to power socket Connect Internet Press pairing button until the Bridge to router LED blinks to activate pairing mode Pairing allows other devices to connect to the Internet Bridge...
  • Page 7 3. Pair Extension Kit with Internet Bridge Wireless Setup: Smart Thermostat installed wirelessly with receiver Smart Thermostat & Extension Kit 3 SEC Blinking 4x short - pause - ... 2 MIN Fast Blinking Press button for 3 sec Paired until LED starts blinking...
  • Page 8 4. Pair Smart Thermostat with Internet Bridge 2 MIN 3 SEC Remove Press button Pairing Paired battery strip and for 3 sec - press button release If failed: • Press the button to clear the error • Restart pairing and make sure that the distance...
  • Page 9 Open Installer Menu 2 MIN 3 SEC 3 SEC Press button Press button Installer Menu is Ready for for 3 sec - for 3 sec - loading configuration release release If failed: • Repeat the process to open Installer Menu •...
  • Page 10 5. Configuration: OpenTherm Wired Setup: Smart Thermostat is wired directly to the boiler Select Select Activate OpenTherm Heating Hot Water Circuit Control Smart Thermostat HC01 Wireless Setup: Smart Thermostat installed wirelessly with receiver Select Select Activate Temperature Heating Hot Water...
  • Page 11 2 MIN Extension Kit OpenTherm installation complete 1. Test the system 2. Hand over the registration card to the customer 2 MIN Extension Kit Select OpenTherm Present Configuration download active Configuration download active after saving Installer Menu after saving Installer Menu (up to 2 min) (up to 2 min)
  • Page 12 1. Wiring: Vaillant eBus Wired Setup: Smart Thermostat is wired directly to the boiler Smart Thermostat Wireless Setup: Smart Thermostat installed wirelessly with receiver Smart Thermostat & Extension Kit...
  • Page 13 Boiler Smart Thermostat MAX 36 V DC eBus Boiler Extension Kit...
  • Page 14 2. Connect Internet Bridge to Router If no free USB jack available - plug to power socket Connect Internet Press pairing button until the Bridge to router LED blinks to activate pairing mode Pairing allows other devices to connect to the Internet Bridge...
  • Page 15 3. Pair Extension Kit with Internet Bridge Wireless Setup: Smart Thermostat installed wirelessly with receiver Smart Thermostat & Extension Kit 3 SEC Blinking 4x short - pause - ... 2 MIN Fast Blinking Press button for 3 sec Paired until LED starts blinking...
  • Page 16 4. Pair Smart Thermostat with Internet Bridge 2 MIN 3 SEC Remove Press button Pairing Paired battery strip and for 3 sec - press button release If failed: • Press the button to clear the error • Restart pairing and make sure that the distance...
  • Page 17 Open Installer Menu 2 MIN 3 SEC 3 SEC Press button Press button Installer Menu is Ready for for 3 sec - for 3 sec - loading configuration release release If failed: • Repeat the process to open Installer Menu •...
  • Page 18 5. Configuration: Vaillant eBus Wired Setup: Smart Thermostat is wired directly to the boiler Select eBus Select Activate Heating Hot Water D05 or D07 Circuit Control (only Smart Thermostat HC01 or for D07) HC02 D05 for systems with a calorMATIC VRC430/470 (VR81)
  • Page 19 2 MIN Extension Kit Vaillant eBus installation complete 1. Test the system 2. Hand over the registration card to the customer 2 MIN Select eBus Extension Kit Present D05 or D07 Configuration download active after saving Installer Menu (up to 2 min)
  • Page 20 1. Wiring: Viessmann KM-Bus Wired Setup: Smart Thermostat is wired directly to the boiler Smart Thermostat Wireless Setup: Smart Thermostat installed wirelessly with receiver Smart Thermostat & Extension Kit...
  • Page 21 KM-Bus Boiler Smart Thermostat MAX 36 V DC KM-Bus Boiler Extension Kit...
  • Page 22 2. Connect Internet Bridge to Router If no free USB jack available - plug to power socket Connect Internet Press pairing button until the Bridge to router LED blinks to activate pairing mode Pairing allows other devices to connect to the Internet Bridge...
  • Page 23 3. Pair Extension Kit with Internet Bridge Wireless Setup: Smart Thermostat installed wirelessly with receiver Smart Thermostat & Extension Kit 3 SEC Blinking 4x short - pause - ... 2 MIN Fast Blinking Press button for 3 sec Paired until LED starts blinking...
  • Page 24 4. Pair Smart Thermostat with Internet Bridge 2 MIN 3 SEC Remove Press button Pairing Paired battery strip and for 3 sec - press button release If failed: • Press the button to clear the error • Restart pairing and make sure that the distance...
  • Page 25 Open Installer Menu 2 MIN 3 SEC 3 SEC Press button Press button Installer Menu is Ready for for 3 sec - for 3 sec - loading configuration release release If failed: • Repeat the process to open Installer Menu •...
  • Page 26 5.Configuration: Viessmann KM-Bus Wired Setup: Smart Thermostat is wired directly to the boiler Select Select KM-Bus Heating Hot Water Circuit Control Smart Thermostat HC01 or HC02 Wireless Setup: Smart Thermostat installed wirelessly with receiver Select Select Temperature Heating Hot Water...
  • Page 27 2 min Extension Kit 2 MIN Extension Kit Select KM-Bus Present Configuration download active after saving Installer Menu (up to 2 min)
  • Page 29 6. Heating System Settings For the heating circuit controlled by tado°, set the same settings as for a Viessmann Vitotrol 200 remote control. Controller Heating System Settings 90: Time constant for calculating the adjusted outside temperature 1 (If 1 can not be selected, A0: Remote Control Vitotronic 200 GW..
  • Page 30 1. Wiring: Worcester HT-Bus Wired Setup: Smart Thermostat is wired directly to the boiler Smart Thermostat Wireless Setup: Smart Thermostat installed wirelessly with receiver Smart Thermostat & Extension Kit...
  • Page 31 Boiler Smart Thermostat MAX 36 V DC Boiler Extension Kit...
  • Page 32 2. Connect Internet Bridge to Router If no free USB jack available - plug to power socket Connect Internet Press pairing button until the Bridge to router LED blinks to activate pairing mode Pairing allows other devices to connect to the Internet Bridge...
  • Page 33 3. Pair Extension Kit with Internet Bridge Wireless Setup: Smart Thermostat installed wirelessly with receiver Smart Thermostat & Extension Kit 3 SEC Blinking 4x short - pause - ... 2 MIN Fast Blinking Press button for 3 sec Paired until LED starts blinking...
  • Page 34 4. Pair Smart Thermostat with Internet Bridge 2 MIN 3 SEC Remove Press button Pairing Paired battery strip and for 3 sec - press button release If failed: • Press the button to clear the error • Restart pairing and make sure that the distance...
  • Page 35 Open Installer Menu 2 MIN 3 SEC 3 SEC Press button Press button Installer Menu is Ready for for 3 sec - for 3 sec - loading configuration release release If failed: • Repeat the process to open Installer Menu •...
  • Page 36 5. Wiring: Worcester HT-Bus Wired Setup: Smart Thermostat is wired directly to the boiler Select Select Activate HT-Bus Heating Hot Water D17 or D18 Circuit Control Smart Thermostat HC01 or (only for HC02 D17) D17 for systems without an FW controller D18 for systems with an FW controller (e.g.
  • Page 37 2 MIN Extension Kit 2 MIN Extension Kit Select HT-Bus Present D17 or D18 Configuration download active after saving Installer Menu (up to 2 min)
  • Page 39 6. Heating System Settings For the heating circuit controlled by tado°, set the same settings as for a Worcester remote control. Controllers Heating System Settings Remote Control FB10 (heating circuit __) Room influence Room influence enabled for FW 100 Comfort-Eco-Frost levels FW 120 FW 200...
  • Page 40 Get expert advice on the tado° installer hotline: 020 3893 2159 or at tado.com/installers 101961_F...

Table of Contents

Save PDF