Canon VB-H651VE Installation Manual

2
ENGLISH
2

Network Camera

Installation Guide

Please be sure to read the "VB-H651VE Installation Guide 1/2" section for correct
use.
Part Names
1
4
2 3
10
11 12
1. Dome case lock screw / 2. Connection slot / 3. Dome case / 4. Reset switch /
5. Heater unit terminals / 6. Reboot switch / 7. Memory card slot / 8. Lens unit / 9. LED (Blue)* /
10. GND screw hole / 11. External device I/O terminals / 12. Audio Input/Output Terminals /
13. Power connection terminal / 14. 100Base-TX LAN connector
* On: when powered on, during reboot / Off: during normal use
External Dimensions
135 (5.31)
Camera mounting tabs
4.8
(0.19)
83.5 (3-9/32)
85.7 (3-3/8)
(*3, *4)
Before Installing the Camera
Set the IP address and other network information on the camera using the "Camera Management
Tool" on the Setup CD-ROM (please refer to "Camera Management Tool User Manual").
Attaching the packing attachment and removing the dome case
Remove the outer tape. Attach the included packing attachment to the connection slot that the
cable will pass through, and attach the connection slot cover to the connection slot that the cable
will not pass through. Use a coin to remove the connection slot cover.
Remove the dome case and remove the locking tape and polystyrene foam attached to the lens
for shipping purposes.
When guiding cables through When guiding cables through
the side the bottom
Packing Attachment
The contents of this guide are subject to change without any prior notice.
BIE-7176-000
5 6 7 8 9
Serial_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
MAC_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
13 14
Camera mounting tab slots
91.2 (3.59)
*1 Ceiling/Wall mount holes
(*4)
*2 Junction box fixing holes
Unit: mm (in.)
*3 Ceiling/Wall mount holes position
*4 Junction box fixing holes position
*5 Camera mounting holes
*6 Direct mount holes position
Guiding the LAN cable through the waterproof packing
2
Using a Memory Card
Memory card
slot
Using the Heater Unit (sold separately)
Connect the two heater cables included with the heater unit to the terminals on the camera side.
Next, attach the heater unit to the camera body and then tighten the screws. Finally, connect the
cables to the heater unit.
Using the Sunshade Cover (sold separately)
The sunshade cover is attached to the camera body together with the dome case. In order to
install it, of the four lock screws for the dome case, remove the two located at the top of the dome
case beforehand. Remove the dome case lock screws by pressing the screws from the inside of
the case and using the dedicated wrench to loosen them.
(*6)
Unit: mm (in.)
Using the Dome Unit (sold separately)
Remove the dome case from the camera, then remove the dome cover holder and dome flange,
and replace with the smoked dome.
Important
• Take care when replacing so as not to scratch the dome cover.
• For proper protection against water and dust, please make sure the screws are firmly tightened during
installation.
Dedicated wrench
❷
❶
Remove the dome case and place the memory card in the
memory card slot.
To remove the memory card, push it in all the way until the
card slightly pops out and remove.
Important
• Insert a memory card before installing the camera.
• When using a memory card with the camera for the first time,
it is recommended to format the card after inserting it into the
camera (please refer to "Operation Guide").
• Always unmount the memory card before removing it (please
refer to "Operation Guide").
❶
❷
Dome flange
Rubber seal
Dome cover
Smoked dome cover
Dome cover holder
❸
Dedicated
wrench