Advertisement
Solving Technical Problems
Problem
Check that the power, audio and IDE cables are correct-
The DVD-ROM drive is not
ly connected to the computer.
detected by the computer.
Change the IDE cable and reconnect it to the computer.
After installing the DVD-ROM
Preferably, connect a second IDE cable to the DVD-ROM
drive, the PC gets slower.
drive in master mode; see page 7 for further details.
Check the position of the jumper in the master/slave
select terminal.
The DVD-ROM drive is not
Reinstall the device driver or update it with the latest
recognized by MS-DOS.
version by downloading it from the Samsung Web site.
The DVD-ROM drive is not
This case may occur when there is a Windows instal-
detected by Windows.
lation problem; reinstall Windows.
No sound is heard from an
Check whether the audio cable is correctly connected
to the sound output terminal on the DVD-ROM drive
audio CD.
and the sound card CD-IN terminal.
Check that the sound card is operational.
Adjust the volume control.
Install the latest version of the device driver.
A CD is not read or is read
too slowly.
Check whether the CD is of good quality and clean it,
if necessary.
The disc compartment will not
Check that the power cable is correctly connected.
open.
Power off and disconnect the PC. Insert a pin or
unfolded paper clip in the emergency hole and push
firmly until the disc compartment opens.
When the MPEG software plays a
Adjust the size of the replay screen.
Video CD, the pictures are not regu-
After checking the display resolution, adjust it, if nec-
lar and the running speed is too slow.
essary.
The computer may not recognize the disc if you start
The Disc is not in message is
playback too quickly after inserting the disc.
displayed even though a disc
Open and close the disc compartment and try again.
has been inserted.
Clean the disc and try again.
The interface mode of the sound card is AT-BUS.
The DVD-ROM drive is not
detected after it is connected
You must therefore connect the DVD-ROM drive to
the IDE port on the PC mother board, rather than to
to a sound card.
the sound card, or install an IDE-compatible sound
card.
Meaning / Solution
8
Technical Specifications
SAMSUNG continually strives to improve its products. Both the design specifications and
these user instructions are thus subject to change without notice.
ITEM
DVD-ROM, DVD-VIDEO, CD-DA(Audio), CD-ROM,
CD-ROM XA, CD-Plus, CD-Extra, Photo-CD(Single,Multi-session),
Disc types supported
DISC
Video CD ready, Enhanced CD, CD-I/FMV, CD-R,CD-RW
Disc diameter
12cm or 8cm
Max. 13,500KB/sec (10X) /
Max. 6,000KB/sec (40X)
Data transfer rate
PIO Mode 4 : 16.6MB/sec
Multiword DMA mode 2 : 16.6MB/sec
UDMA mode 2 : 33MB/sec
Access time(1/3stroke)
130ms / 110ms(Typical)
DRIVE
PERFORMANCE
Data buffer capacity
512KB
Laser
Semiconductor Laser
Slide mechanism
Stepping motor
Spindle motor
Brushless motor
Tray. DC motor(Soft Eject). Horizontal/Vertical
Loading mechanism
ERROR RATE
Eject button
Auto eject or Auto inject
Indicator(LED)
BUSY
FRONT PANEL
Headphone output
Stereo mini-jack(Ø3.6mm) 0.60±20%(rms) 33Ω
Volume control
Wheel knob
Required power
+5VDC : 2.0A, +12VDC : 1.0A (Max)
Interface connector
ATAPI
REAR PANEL
Audio output
Line out 0.70
Jumper block
Device configuration jumper
Operation
Temperature : 5 ~ 45°C,
OPERATING
ENVIRONMENT
Storage
Temperature : -40 ~ 60°C,
Dimensions
149(W) x 42(H) x 200(D)mm
GENERAL
Net weight
880g
125,000 POH(Duty 20%)
RELIABILITY
MTBF
* In case of the PC without UDMA, it may have a different DVD data transmission rate.
SD - 610
SD - 612
DVD / CD
Sustained :
Sustained :
Max. 16,200KB/sec (12X) /
Max. 6,000KB/sec (40X)
10
/ MODE1:10
, MODE2:10
-15
-12
-9
±
20%(rms) : 47KΩ
Humidity : 8 ~ 80%
Humidity : 5 ~ 90%
9
Advertisement
