Advertisement
Quick Links
103450
POWER PRO 900W Bridge Saw
Owner's Safety and Operating Manual
Safety First
Read manual before use. Keep hands arms and face clear
of blade whilst in use. Always have safety guard in place
when machine is switched on at the mains.
Always wear Vitrex Protective Equipment when using
hand or power tools.
Advertisement
Related Manuals for Vitrex VERSATILE POWER PRO 900W
Summary of Contents for Vitrex VERSATILE POWER PRO 900W
- Page 1 103450 POWER PRO 900W Bridge Saw Owner’s Safety and Operating Manual Safety First Read manual before use. Keep hands arms and face clear of blade whilst in use. Always have safety guard in place when machine is switched on at the mains. Always wear Vitrex Protective Equipment when using hand or power tools.
- Page 2 POWER PRO 900W Bridge Saw Owner’s Safety and Operating Manual Contents Safety Instructions ........... 3 Machine Specification & Electrical Requirements ..4 Assembly & Operating Instructions ...... 5-7 Maintenance & Warranty ......... 8 Tel: +44 (0) 1253 789180...
- Page 3 Power Pro 900W Bridge Saw Safety Instructions • When using an extension lead, check that it is capable of carrying the current required - failure to do so may result in loss of power To use this tool correctly, you must and overheating. observe the Safety Regulations, the Assembly Instructions and the Operation • Do not leave the saw running Instructions contained in this Manual. unattended or touch the blade whilst in motion – always use the blade guard All persons who use and service the when cutting. machine must be acquainted with this Manual and must be informed about any • Replace damaged blades immediately potential hazards. and ensure that new blades are fitted correctly to run in the direction Children and infirm people must not use indicated on the blade. this tool. Children must be supervised at all times if they are in the area in which • Only recommended replacement parts the tool is being used. should be used with this machine – use of improper accessories could cause serious It is also imperative that you observe the injury accident prevention regulations in force in your area. The same applies for general rules of occupational health and safety.
- Page 4 • Operating handle • Repair or replace damaged or worn cable immediately after first disconnecting from • Steel shelf mains supply. • 2 Rear Wheel attachments • Electrical faults must only be carried out by • Water Pump and Tray a qualified electrician. • Owner’s Safety & Operating Manual • Immediately switch off the saw in the case of: - Excessive sparking of the brushes - Malfunction of the main plug, socket or damaged cables - Broken switch - Smoke or smell caused by scorched insulation IMPORTANT For best results with your new Vitrex Versatile Power Pro 900W Bridge Saw allow the blade to do the work, rather than forcing the tile through the machine. Should the blade stop, simply ease the tile away and then continue cutting using slightly less pressure. Tel: +44 (0) 1253 789180...
- Page 5 Power Pro 900W Bridge Saw Assembly & Operation Operating Instructions Straight Cuts Remove the saw from its carton, lay carefully on its side. Unfasten blade carriage retaining bolt. Pull down the legs and fasten the four safety brackets to them using the arms. Push the blade carriage to its furthest point away from the operator. Place the tile in position on the cutting table so that it rests against the measuring scale and mitre guide. Make sure the wheels are tightened. Set the size of cut required on the measuring scale and lock the mitre guide. Switch on the machine. Ensure that the drain plug is in position, then fill the water tray until the pump is almost sub- merged. (approx. 10 litres). Check water level regularly and top up as necessary. Pull the blade carriage steadily towards you, cutting through the tile. When the cut is complete, switch off the machine, removing the cut tile pieces and any debris.
-
Page 6: Mitre Cuts
Angular Cuts Place the tile in position on the cutting table so Tilt the bridge to the desired angle (up to 45 ) and that it rests against the measuring scale and the re-tighten. mitre guide. Place the tile in position on the cutting table so Loosen the winged screw on the mitre guide and that it rests against the measuring scale and mitre set the angle of cut required. guide. Pull the blade carriage steadily towards you, Switch on the machine. Pull the blade carriage cutting through the tile. When the cut is complete, steadily towards you, cutting through the tile. - Page 7 Power Pro 900W Bridge Saw Transportation Remove the two cover retaining screws and take For transportation the saw between jobs, wheels off the blade guard. can be mounted at the top of the folded legs, just below the angled stabilising bracket. The saw can now be moved by lifting the handle at the opposite end of the machine. Pump Maintenance Whilst holding the shaft with the spanner wrench, turn the blade retaining nut clockwise to release using the hex wrench. Ensure that the new blade is correctly seated against the shaft and that the directional arrow matches that on the blade guard. Replace the flange and nut, taking care not to overtighten. Rotate blade to ensure correct alignment. Replace the blade guard and water tubes. Note: Please clean the pump immediately after you stop use. Otherwise the filter foam and the impeller could be stuck by the dry debris. So you must replace the filter Moving the Bridge Saw foam or the pump. 1. Clean the pump To clean the pump, remove the intake Cover, and then take out of the filter foam and impeller cover.
- Page 8 • Additional recycling information can • Always clean the machine after use, after be found through your local Authority first ensuring that it is disconnected from or Retailer. the mains. • Rinse out reservoir thoroughly to remove all sludge and wipe down outside of machine using a cloth or sponge. • When not in use, store the electrical cable and plug under the machine in the space provided. • For further information or advice, please call the Vitrex Technical Helpline • No other servicing is required in normal on +44 (0) 1253789180. use. No attempt should be made to repair or replace internal components as this will invalidate any claim whilst the product is under guarantee. This electric tile cutter has been manufactured to a high quality standard. It is guaranteed against faulty materials and workmanship for 12months from the date of purchase. Any claim must be accompanied by a valid till receipt as proof of purchase. A faulty machine will either be repaired or replaced free of charge. If a direct replacement is not available, an alternative to the same or greater value/specification will be offered. This guarantee does not cover machine defects caused by or resulting from: a) Misuse, abuse or neglect, b) Trade, Professional or hire use, c) Repairs attempted by anyone other than our authorised repair agent, d) Ingress of foreign objects, substances or accident In the unlikely event of a fault occurring, contact should be made through the Vitrex Technical Helpline +44 (0) 1253 789180 The above guarantee is only valid within the UK and does not affect your statutory rights.
Need help?
Do you have a question about the VERSATILE POWER PRO 900W and is the answer not in the manual?
Questions and answers