Mitsubishi Electric MELSEC FX2N-16CCL-M Hardware Manual

This manual contains text, diagrams and explanations which will guide the reader in the correct installation
and operation of the FX
understood before attempting to install or use the unit. Further information can be found in the FX series
PLC hardware manuals.
Guidelines for the safety of the user and protection of the FX
SYSTEM MASTER BLOCK
• If in doubt at any stage during the installation of the FX
BLOCK always consult a professional electrical engineer who is qualified and trained to the local
and national standards. If in doubt about the operation or use of the FX
SYSTEM MASTER BLOCK please consult the nearest Mitsubishi Electric distributor.
• Under no circumstances will Mitsubishi Electric be liable or responsible for any consequential
damage that may arise as a result of the installation or use of this equipment.
• All examples and diagrams shown in this manual are intended only as an aid to
understanding the text, not to guarantee operation. Mitsubishi Electric will accept no
responsibility for actual use of the product based on these illustrative examples.
• Owing to the very great variety in possible application of this equipment, you must satisfy
yourself as to its suitability for your specific application.
Note's on the symbology used in this manual
At various times through out this manual certain symbols will be used to highlight points of information
which are intended to ensure the user's personal safety and protect the integrity of the equipment.
Whenever any of the following symbols are encountered, its associated note must be read and
understood. Each of the symbols used will now be listed with a brief description of its meaning.
Hardware warnings
1) Indicates that the identified danger WILL cause physical and property damage.
2) Indicates that the identified danger could POSSIBLY cause physical and property damage.
1. INTRODUCTION
1.1 Associated Manuals
Manual name
★FX
-16CCL-M
2N
User's Manual
★FX
/FX /FX /FX
1S 1N 2N
Programming Manual II
★FX
/FX
3U 3UC
Programming Manual
✩FX
Hardware Manual
1N
✩FX
Hardware Manual
2N
✩FX
Series User's
3U
Manual
- Hardware Edition
✩FX
Hardware Manual
2NC
✩FX
Series User's
3UC
Manual
- Hardware Edition
✩FX
-32CCL
2N
User's Manual
★: Indispensable manual
✩: Manual required depending on equipment used
FX
-16CCL-M CC-Link SYSTEM MASTER BLOCK. It should be read and
2N
Manual number
JY992D93101
(sent separately)
JY992D88101
2NC
(sent separately)
JY997D16601
(sent separately)
JY992D89301
(packed with product)
JY992D66301
(packed with product)
JY997D16501
(sent separately)
JY992D76401
(packed with product)
JY997D28701
(sent separately)
JY992D71801
(packed with product)
-16CCL-M CC-Link SYSTEM MASTER BLOCK
2N
HARDWARE MANUAL
-16CCL-M CC-Link SYSTEM MASTER
2N
Describes programming and handling of the CC-
Link master block FX
Explains the instructions available to the FX
FX /FX /FX
1N 2N
Explains the instructions available to the FX
FX Series PLC.
3UC
Describes hardware specifications, wiring and
mounting of the FX
Describes the contents related to the hardware
such as specifications, wiring and mounting of the
FX Series PLC.
2N
Describes the hardware specifications, wiring and
mounting of the FX
Describes the hardware specifications, wiring and
mounting of the FX
Describes the hardware specifications, wiring and
mounting of the FX
Describes programming and handling of the CC-
Link interface block FX
JY992D93201C
-16CCL-M CC-Link
2N
-16CCL-M CC-Link
2N
Description
-16CCL-M.
2N
Series PLC.
2NC
Series PLC.
1N
Series PLC.
3U
Series PLC.
2NC
Series PLC.
3UC
-32CCL.
2N
CC-Link Ver.1.10
/
1S
/
3U