Table of Contents
Advertisement
ADT
T Pulse
W
ireless
Quic
Pro
perty of ADT
T, LLC. Infor
"as
is" without w
warranty of a
©20
017ADT LLC
C dba ADT S
logo
o, 800 ADT.A
ASAP and th
mar
rks and/or re
egistered ma
DBC
C835
e
Inte
ractiv
®
DB
C835
s HD
Doorb
k Inst
tallatio
rmation accu
urate as of pu
any kind.
Security Serv
vices. All rig
he product/s
service nam
arks. Unaut
thorized use
ve Solu
utions
bell Ca
amera
on Gu
ide
ublished dat
te and is pro
ghts reserve
ed. ADT, the
mes listed in t
this docume
e is strictly p
rohibited.
s
a
vided
ADT
ent are
Advertisement
Table of Contents
Related Manuals for ADT Pulse DBC835
Summary of Contents for ADT Pulse DBC835
- Page 1 T Pulse Inte ractiv ve Solu utions ® C835 ireless s HD Doorb bell Ca amera Quic k Inst tallatio on Gu perty of ADT T, LLC. Infor rmation accu urate as of pu ublished dat te and is pro vided “as is”...
- Page 2 1. D Doorbell C Camera x 1 2. T Two Mount ting Bracke ets (Small & One gan ng-box size 3. W Wood Scre ew/Anchor 4. G Gang Box S Screw x 2 DBC835 W Wireless Doo orbell Came era Installat...
- Page 3 Chapter 1: Introduction Overview DBC835 supports both analog and digital chime within AC 8-24 voltage. The operation temperature is –4°F to 122°F. (–20°C to 50°C) (The battery will not be charged when the temperature is < 0°C) Figure 1: Front Panel...
- Page 4 WPS function has failed. Blinking (Red) - Network connection is failed. Spinning (Green). The firmware is being upgraded. Intermittent Blinking (Red) – If the LED is blinking for 2 seconds, means AC power is disconnected. DBC835 Wireless Doorbell Camera Installation...
-
Page 5: Basic Setup
Basic Setup This section provides information on how to assemble and configure the DBC835 Doorbell Camera for enrollment. Installation 1. Power Up and check the LED Turn on the switch on the rear side of the doorbell camera and wait for 20 seconds until the LED turns to flashing red. - Page 6 DBC835 Doorbell Camera into the ADT Pulse network. This process uses the Wi-Fi Protected Setup (WPS) with PIN method to wirelessly enroll the HD Camera to the gateway via the ADT Pulse Portal or TS Installer App. Using WPS with PIN to Enroll the Doorbell Camera 1.
- Page 7 Figure 5: Clicking "Add Using WPS" Button 6. Locate the camera’s PIN number on the label on the rear of the camera. Enter the PIN number in the WPS PIN field. Figure 6: Entering the PIN DBC835 Wireless Doorbell Camera Installation...
- Page 8 The remaining time is displayed in the upper left portion of the screen. 8. Click the Continue button to initiate the WPS process. Figure 7: Clicking "Continue" Button Figure 8: Add Camera Using WPS Screen DBC835 Wireless Doorbell Camera Installation...
- Page 9 Click Save after entering all the data. Figure 9: Saving Camera Details 10. The newly-added device will be shown in the Cameras list, then click Go Back at the top left of the screen. Figure 10: Clicking Go Back Button DBC835 Wireless Doorbell Camera Installation...
- Page 10 LED to see if the camera still has WiFi connectivity. Note: If the WiFi cannot reach the front doorbell camera, you will see the power LED kept blinking red. Then a repeater is required or move the CloudLink/TSS to the center of the house. DBC835 Wireless Doorbell Camera Installation...
- Page 11 ardwa are In nstalla ation This s section pr rovides det tails for wa ll mounting g of the DB BC835 orbell Cam mera. stallatio Note: Ensure tha at the cam era is conf figured and d enrolled i n ADT Pulse before per rmanently...
- Page 12 Figure 15: Choosing Mounting Bracket 4. Use the AC wires from the existing traditional doorbell and connect the AC wires to screw terminals of the bracket. Figure 16: Connecting the AC Wires DBC835 Wireless Doorbell Camera Installation...
- Page 13 Chapter 4: : Hardware e Installatio Secure the e bracket w with screws s. Please s see Figure e 17. Note: Inse ert the anch hors if nec essary. ure 17: Ins stalling the e Screws 6. A Attach the d doorbell ca amera to th he mountin...
- Page 14 Utilitech Model # UT-2735-02 Utilitech Model # UT-7574-02 Utilitech IQ America Model # DW-2403A Hampton Bay Model # HB-7621-02 Honeywell Model# RCW102N Honeywell Model# RCW251N NuTone Model# LA100WH NuTone Model# LA126WH Heath Zenith Model# DC3360 DBC835 Wireless Doorbell Camera Installation...
- Page 15 This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body. DBC835 Wireless Doorbell Camera Installation...
- Page 16 Le dispositif rencontre l'exemption des limites courantes d'évaluation dans la section 2.5 de RSS 102 et la conformité à l'exposition de RSS-102 rf, utilisateurs peut obtenir l'information canadienne sur l'exposition et la conformité de rf. DBC835 Wireless Doorbell Camera Installation...
Need help?
Do you have a question about the DBC835 and is the answer not in the manual?
Questions and answers
How do I get my camera in doorbell to change to my new WiFi that I changed to. Light shows green. Have reset it 3 times alreadyEverything else is online.
To connect your ADT Pulse DBC835 doorbell camera to a new WiFi network, follow these steps:
1. Power up the camera and wait for the LED to start flashing red.
2. Access the ADT Pulse portal or TS Installer app:
- Open an Internet browser and log in to the Pulse portal.
- Go to the "System" tab and click "Manage Devices."
- Click on "Cameras."
3. Use WPS with PIN to connect:
- Press and hold the Doorbell/WPS button for 0-10 seconds to enter WPS Pin Code mode.
- Follow the on-screen instructions in the Pulse portal or TS Installer app to enter the PIN and complete the connection.
4. Verify the connection:
- A solid blue LED indicates a successful connection.
- If the LED blinks red, the network connection has failed, and you should retry the steps.
Make sure your WiFi network is active and within range of the doorbell camera.
This answer is automatically generated
Ring doorbell is connected, lights are green. How do I make it the pictures.
You can view pictures from the ADT Pulse DBC835 Doorbell Camera on your smartphone, tablet, or ADT Pulse Portal. The camera delivers 720P HD resolution, allowing you to see who is at your door through these devices.
This answer is automatically generated