Topcon X35 Console Operator's Manual
  1. Manuals
  2. Brands
  3. Topcon Manuals
  4. Controller
  5. X35
  6. Operator's manual

Topcon X35 Console Operator's Manual

Hide thumbs Also See for X35 Console:

Advertisement

Table of Contents

See also: Operator's Manual
X35
X30
X25
•
Console
Cameras
Operator's Manual
www.topconpositioning.com

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the X35 Console and is the answer not in the manual?

Questions and answers

Related Manuals for Topcon X35 Console

Summary of Contents for Topcon X35 Console

  • Page 1 • Console Cameras Operator’s Manual www.topconpositioning.com...
  • Page 3 © Copyright Topcon Precision Agriculture June 2017 All contents in this manual are copyrighted by Topcon. All rights reserved. The information contained herein may not be used, accessed, copied, stored, displayed, sold, modified, published or distributed, or otherwise reproduced without express written consent from Topcon.
  • Page 5 - No statement contained at the website of TPA WEBSITE AND OTHER STATEMENTS or any other Topcon Group company or in any other advertisements or TPA literature or made by an employee or independent contractor of TPA modifies these Terms and Conditions.
  • Page 6 defective item at no charge, and ship it back to you. You must pay the shipping and handling charges in respect of the same. Calibration of components, labor and travel expenses incurred for in-field removal and replacement of components are not covered in this warranty policy. The foregoing warranty shall NOT apply to damage or defects resulting from: (i) ...
  • Page 7 Other These Terms and Conditions may be amended, modified, superseded or cancelled, at any time by TPA. These Terms and Conditions will be governed by, and construed in accordance with: the laws of South Australia if the product is sold and supplied to you in Australia (in which case the courts of South Australia or the Federal Court of Australia (Adelaide Registry) have exclusive jurisdiction in respect of any claim or dispute) or the laws of the State of California if the product is sold and supplied to you outside of Australia...
  • Page 8 You can check if interference is being caused by this equipment by turning the Topcon equipment off to see if the interference stops. If the equipment is causing interference to a radio or other electronic device, try: Turning the radio antenna until the interference stops...
  • Page 9 Good safety practices not only protect you, but also the people around you. Study this manual as part of your safety program. This safety information only relates to Topcon equipment and does not replace other usual safe work practices. WARNING: Ensure power is removed from the Topcon equipment prior to maintenance or repair of the vehicle or implements.
  • Page 10 However, it is always advisable not to handle damaged electronic equipment. This Topcon product may contain a sealed lithium battery. Always dispose of any electronic equipment thoughtfully and responsibly.
  • Page 11 Topcon accepts no responsibility or liability for damages to property, personal injuries, or death resulting from the misuse or abuse of any of its products. Further, Topcon accepts no responsibility for the use of Topcon equipment or the GNSS signal for any purpose other than the intended purpose.
  • Page 12 Operation and Risk of Obstacles The following list is not exhaustive or limited. To use the console for assisted steering along a defined wayline, the operator must ensure that it is used: Away from people and obstacles Away from high voltage power lines or other overhead obstructions (identify any clearance problems before activating the console) On private property without public access Within cleared fields...
  • Page 13 Be aware of file format compatibility. Discuss compatible formats with the dealer. Topcon Agricultural Products are hardy and designed to work in tough conditions. However, if equipment is unused for a length of time, store away from water and direct heat sources.

  • Page 14: Table Of Contents

    Table of contents Chapter 1 – Introduction 1.1. Parts list 1.2. Camera mounting suggestions 1.3. Installation Chapter 2 – Camera Setup 2.1. Setting up general camera settings 2.2. Setting up default camera settings Chapter 3 – Camera Operation 3.1. Monitoring with mini-views 3.2.

  • Page 15: Chapter 1 - Introduction

    Chapter 1 – Introduction The camera monitor allows users to display and monitor cameras on the console operation screen. X35 and X25 consoles Up to six cameras may be connected. Four via the USB adapter and two via the analog ports. Four cameras may be displayed live at one time.
  • Page 16 1.1. Parts list Part Number Description A3453 CABLE, AgCam ext 20 foot x 2 1004051-01 PSWD-CG, Camera Unlock Code x 1 AGA5107 MANUAL, Camera Monitor x 1 Y216 CABLE TIE, 160 mm x 2.6 mm black x 20 AGW289 WARRANTY CARD, AG Universal x 1 X35 and X25 consoles 1019150-1 KIT, X35/X25 AgCam 1 camera with 20ft cable Part Number...
  • Page 17 Chapter 1 – Introduction Part Number Description 1004051-01 Camera Unlock Code x 1 AGA5107 MANUAL, Camera Monitor x 1 AGW289 WARRANTY CARD, AG Universal x 1 Note: 1019151-01 KIT is also available. This provides two cameras, adapters and cables.

  • Page 18: Camera Mounting Suggestions

    1.2. Camera mounting suggestions 1.2. Camera mounting suggestions WARNING: Never rely on your AgCam system as a safety feature. WARNING: Ensure cables do not interfere with any vehicle operation or moving parts. Cables should be secured using supplied cable ties. Note: It is recommended that cable ties are used to secure cameras in place in case they are knocked loose for any reason.

  • Page 19: Installation

    Chapter 1 – Introduction 1.3. Installation 1. Attach the cameras to the desired locations on the vehicle. The camera bases are magnetic and may be attached to any metallic object. 2. Connect the A3453 CABLES to each camera and run the cables into the cabin at a suitable entrance.
  • Page 20 1.3. Installation...

  • Page 21: Chapter 2 - Camera Setup

    Chapter 2 – Camera Setup Note: The camera monitoring software requires a license. Contact your dealer for details. 2.1. Setting up general camera settings 1. Select System / Cameras / General 2. Select the camera from the tabs on the left. The following options are available for each installed camera: Name: The camera name that will be displayed on the Operation screen.

  • Page 22: Setting Up Default Camera Settings

    2.2. Setting up default camera settings 2.2. Setting up default camera settings 1. Select System / Cameras / Default The following options are available: Camera loop time: Time in seconds (between 5 and 30) before moving to the next camera when looping through cameras automatically.

  • Page 23: Chapter 3 - Camera Operation

    Chapter 3 – Camera Operation Once cameras have been set up, the console may be used to monitor the camera output during operation. 3.1. Monitoring with mini-views 1. Select the camera icon to open a mini-view. 2. Select the icon again to open a mini-view of another camera. Repeat to view up to three mini-views at a time.
  • Page 24 3.1. Monitoring with mini-views 5. Use the arrows to move between the enabled camera views or press to select a camera. 6. Select the preferred camera and confirm.
  • Page 25 Chapter 3 – Camera Operation 7. Select to split the screen to show up to four camera views. Each of these four screens now show the screen controls when pressed. 8. To return to single screen view, select the view that is to be expanded.

  • Page 26: Using Full Screen View

    3.2. Using full screen view 3.2. Using full screen view 1. To move a mini-view to the full camera panel, select the mini- view and slide from left to right towards the full screen or select the maximize button in the top right corner. Guidance and other open panels will reduce to mini-views.
  • Page 27 Chapter 3 – Camera Operation 3. To move a view on the ribbon to the main screen, select a camera view and slide to the main screen. 4. To see multiple views on the main camera screen, select the screen to see screen controls.

  • Page 28: Camera Loop

    3.3. Camera loop 3.3. Camera loop It is possible to automatically loop through selected cameras. See Setting up general camera settings, page 7 for setup information. 1. Select to display the Camera loop option.
  • Page 30 Avenida de la Industria 35 Tres Cantos 28760, Spain Phone: +34-91-804-92-31 Fax: +34-91-803-14-15 Topcon Corporation 75-1 Hasunuma-cho, Itabashi-ku Tokyo 174-8580 Japan Phone: +81-3-5994-0671 Fax: +81-3-5994-0672 © 2016 Topcon Precision Agriculture All rights reserved Specifications subject to change without notice AGA5107...

This manual is also suitable for:

X25 consoleX30 console

Table of Contents