Howard Miller 615-052 Instructions

615-052 INSTRUCTIONS
STABILITY AND LOCATION:
Fountain must be installed and located on a level, smooth and flat
!
surface for proper stability and function.
Fountain and its components are designed for INDOOR use only.
!
F ountain should NOT be used in temperatures near or below freezing.
!
It is recommended that this Fountain NOT be placed in a recreational or
!
play area. Damage to the Fountain and/or personal injury could result if
children/persons are permitted to climb, play, or lean on this clock.
CAUTION :
Slippery floor conditions may occur if the Fountain water splashes the
!
surrounding area. See the Troubleshooting Section to adjust the Pump
water flow speed.
WARNING Electric Shock Hazard -
:
Keep electrical cords away from high temperature heat sources.
!
E nsure excess power cords are stowed to avoid tripping.
!
Use 110V AC electrical outlet with Ground Fault Interrupt (GFI)
!
receptacle. Follow all local electrical codes.
Keep transformer socket and plug off the floor and away from
!
where it could get wet from water.
TOOLS REQUIRED FOR ASSEMBLY: (not included)
1 - SCREW DRIVER - Slotted
1 - SCREW DRIVER - Phillips
1 - LEVEL
( included )
PARTS LIST:
1 - Wall Section 1 - Pendulum
1 - Basin 1 - Dial
1 - Pump 1 - Movement Cover
1 - Spotlight 1 - Bag of River Rocks
1- Transformer 5 - Spare light bulbs (for Spotlight)
2 - Anchor Bolts 2 - Brass Pegs with rubber stopper on one end
1 - Light Cup 1 - Brass Rod without rubber stopper
MOVEMENT
5 SPARE
DIAL
COVER
LIGHT BULBS
ANCHOR
BRASS BRASS
PEGS ROD BOLTS
(WITH (WITHOUT
RUBBER RUBBER
STOPPER) STOPPER)
PENDULUM
WALL SECTION
PUMP
SPOTLIGHT
RIVER
TRANSFORMER
BASIN
ROCKS
STEP 2: Connect Pump
Set Wall Section on a flat surface, face down.
!
Locate the end of the Water Hose, on the bottom of the Wall Section.
!
Attach the Pump to the Water Hose. Verify the Hose is pushed all the
!
way onto the pump.
DO NOT PLUG INTO 110V AC ELECTRICAL OUTLET AT THIS TIME.
PUMP
WATER HOSE
STEP 3: Basin and Spotlight
Place the Basin on a flat surface where the fountain will be located.
!
(near two electrical outlets.)
Level the Basin using the Floor Levelers on the bottom of the Basin.
!
Place the Spotlight in the bottom of the Basin at the front center.
!
Route the Spotlight power cord out of the Basin through the slot at
!
the back edge. Leave 6-8 inches of extra power cord in the Basin with
the Spotlight.
SPOT
SPOTLIGHT
LIGHT
CORD
FLOOR
BASIN
LEVELERS
(two people recommended)
Carefully lift the Wall Section and the
!
attached Pump over the Basin. (One
person to hold the Wall Section, one
person to hold the Pump.)
Put the Pump into the center of the Basin.
!
Route the Pump power cord out of the
!
Basin through the slot at the back edge.
Lower the Wall Section onto the
!
supports in the Basin so that the holes
in the Mounting Plate align with the
holes in the Basin Supports.
Thread the Anchor bolts through the
!
holes in the Wall Section Mounting
Plate and into the Basin supports.
Tighten the Anchor bolts with screw
!
BOLT
driver.
Verify the Wall Section is level by
!
adjusting the Levelers. (see Step 3)
NOTE: Do NOT push on the Wall
Section to access the Floor Levelers or
move the unit. Lift from the Basin to
adjust the Floor Levelers.
Locate the Light Cup. Place the Light Cup into
! !
position in the Wall Section
Lift the Spotlight from inside
!
the Basin (see Step 3) and Mounting Plate as shown.
position into the Light Cup.
LIGHT
CUP
SPOT
MOUNTING
LIGHT CUP LIGHT
PLATE
STEP 6: Spotlight to Transformer
Connect the plug at the end of the Spotlight cord into the socket on
!
the Transformer.
Verify that neither the Transformer nor the connection between the
!
Transformer and Spotlight cord are in the Basin where they could
get wet.
Do NOT allow the socket and plug connection between the Spotlight
!
and the Transformer to get in contact with the ground where contact
WALL
with water could cause electrical shock.
SECTION
(BACK SIDE
DO NOT PLUG INTO 110V AC ELECTRICAL OUTLET AT THIS TIME.
VIEW)
SPOTLIGHT
CORD
STEP 7: Add water
DO NOT PLUG INTO
Fill the Basin with clean water, up to
!
110V AC ELECTRICAL
underside of Mounting Plate, so that the
OUTLET AT THIS TIME.
pump is completely submerged in the
water . (Distilled, bottled or spring water
are recommended. Do not use hot water.)
NOTE: Only the Pump, the electrical cord
directly connected to the Pump, and the
Spotlight cord are to come in contact with
LEVEL
Under no circumstances should the
water.
Transformer, the connection between the
Spotlight cord plug and the Transformer
socket or other parts come into contact
with water.
Due to natural evaporation, check water
!
level DAILY . Pump must be submerged to
WALL
operate properly.
SECTION
NOTE: Typically the Fountain will require
water added every one to two days.
Place River Rocks on the Wall Section
!
BOLT
Mounting Plate.
STEP 8: Clock Instructions
CORDS
Install the batteries according to the +/- symbols.
!
Set the time using the Time Setting Knob.
MOUNTING
!
Position the Movement Cover over the Movement to keep water
PUMP
PLATE
!
from the Fountain off the Movement.
BASIN
BASIN
SUPPORTS
TIME
SETTING
PENDULUM
KNOB
BATTERY REPLACEMENT:
If the clock begins to lose time, or the pendulum swing begins to
slow, it is the sign of weak or exhausted batteries. Replace battery
with a fresh "AA" Alkaline battery.
IMPORTANT: Never leave an exhausted battery in your clock as it
could leak and damage your clock.
STEP 9: Dial and Pendulum
Screw the Brass Pegs with rubber stoppers into the bottom two
!
holes of the Wall Section, as shown below.
Screw the Brass Rod without the rubber stopper into the top hole of
!
the Wall Section, as shown below.
NOTE: Some threads will remain exposed on the Pegs and Rods.
Slide the Dial Mounting Sleeve over the Brass Rod near the top of the
!
Wall Section until the back of the Dial rests against the Brass Pegs.
Align the Dial so that it hangs straight and level.
!
Tighten the Set Screw on the Dial Mounting Sleeve.
!
Hang the Pendulum onto the Pendulum Hanger (see Step 8)
!
Start the Pendulum swing by gently moving the Pendulum to the left
!
or right side of the Fountain and release. The pendulum will settle
into an even swinging motion after a few minutes.
SOCKET
TRANSFORMER
PLUG
DIAL
MOUNTING
SLEEVE
PUMP POWER CORD
PEG
DIAL
(SIDE
FILL BASIN WALL
VIEW)
SECTION
WITH WATER
*CHECK WATER (SIDE VIEW)
LEVEL DAILY
STEP 10: Start Fountain
RIVER
ROCKS
Verify that the water level allows the Pump to be
!
completely submerged in the water.
Plug Pump power cord and Transformer into
!
110V AC electrical outlet with GFI receptacle
Do NOT plug-in or use this product if any part of it
appears to be damaged or operates abnormally.
Have the product examined and repaired, if
necessary, by a qualified electrician.
Pump will begin to fill the Reservoir at the top of
!
the Fountain Wall Section.
Reservoir at the top of the Fountain before water
can begin to flow out of Fountain. This could take
up to a minute for the water to begin flowing.
there is still no water flow after a minute, you will
need to prime the Pump.
MOVEMENT
Adjust the Spotlight so that it shines
!
BACK
on the Fountain as desired.
SIDE
OF
PRIMING THE PUMP
DIAL
Plug the Pump power cord into 110AC electrical
!
outlet for 1-2 minutes. If water does not flow out of
the top of the Fountain, unplug the power cord.
Repeat above step as necessary to cycle the
!
Pump
This "Priming" action is normal and is generally
MOVEMENT not necessary after initial installation.
HANGER
DO NOT
COVER let the Pump operate when not fully
submerged in water. Doing so may damage the
Pump. Always submerge the Pump in water, and
then plug in the power cord.
NOTE:
If water flows out of the top of the unit
unevenly, see the Troubleshooting section.
BRASS ROD
SET
(WITHOUT
SCREW
RUBBER
STOPPER)
ROD
BRASS PEGS
(WITH RUBBER
STOPPERS)
DIAL
PENDULUM
WALL
SECTION
RESERVOIR
.
Pump MUST first fill the
PUMP
If
POWER
CORD
:
TRANSFORMER
SPOT
LIGHT
495738-R2