Mitsubishi Electric MSZ-FH Series User Manual

Simple Remote Controller User Guide
【MSZ-FH series】
The remote controller has a simple,
stylish design with emphasis on
the use of straight lines. The unit
can be turned on/off and the
temperature adjusted with the
cover closed.
A
SELECTING OPERATION MODES
1
Press to start the operation.
2
Press to select operation mode. Each press
changes mode in the following order:
A ( U T O ) ( C O O ) L ( D R ) Y ( H E A ) T F ( A
3
Press or to set the temperature.
Each press raises or lowers the temperature by 1°C.
B
CONVENIENT ONE-TOUCH FUNCTIONS
Press these buttons to toggle these functions on/off.
ECONO COOL
A swing pattern is used for airflow to create an enhanced
cooling sensation. This allows the temperature to be set 2°C
higher without any loss of comfort.
POWERFUL
Air conditioner operates at maximum capacity for 15 minutes.
i-save
Setting preferences can be saved and then activated in
future uses simply by pressing the pressing the i-save button.
In normal heating mode, the lowest possible temperature setting is
16°C, but using i-save, this value can be set as low as 10°C.
Note:
In the case of systems with multiple units (multi-systems), it is not
possible to set different operation modes for each unit. In addition,
in some cases, it may not be possible to use certain functions.
PREPARATION BEFORE OPERATION (SETTING CURRENT TIME)
1 2
Press CLOCK Press the TIME
button.
button to set the
time.
A
N )
B
D
3 4
Press the DAY Press CLOCK
button to set the again.
day.
C
FAN SPEED AND AIRFLOW DIRECTION ADJUSTMENT
FAN
Press to select fan speed.
Each press changes fan speed
(AUTO)
in the following order:
WIDE VANE
Press to select horizontal airfl ow direction.
Each press changes airfl ow direction
in the following order:
D
What is "NATURAL FLOW"?
As time passes, airfl ow will become more
like natural wind. The continuously gentle
breeze provides enhanced comfort for
occupants.
Press this button to toggle the function on/off.
F
TIMER OPERATION
C
ON/OFF TIMER
1
Press or during operation to set the timer.
(ON timer) : The unit turns ON at the set time.
(OFF timer) : The unit turns OFF at the set time.
* or blinks.
* Make sure that the current time and day are set correctly.
E
2
Press (Increase) and (Decrease) to set the
time of timer.
Each press increases or decreases the set time by 10 minutes.
• Set the timer while
or is blinking.
3
Press or again to cancel timer.
G
i-see OPERATION
i-see control mode
1
Press during COOL, DRY,
HEAT and AUTO mode to
activate i-see control mode.
• Press gently using a thin instrument. •
lights. (Operation display section)
F
• The default setting is "active".
2
Press again to activate
G ABSENCE DETECTION.
•
lights. (Operation display section)
3
Press again to release
i-see control mode.
L-VANE-R
Press
Each press changes airfl ow direction in the following order:
(Silent) (Low) (Med.) (High) (Super High)
(AUTO)
(SWING)
E
What is "Air Purifying"?
The purifier neutralizes bacteria as it
passes through the plasma device.
Press this button to toggle the function on/off.
WEEKLY TIMER
1
Press to enter the weekly timer setting mode.
2
Press and to select setting day and number
3
Press , , and to set ON/OFF, time, and temperature.
4
Press to complete and transmit the weekly timer setting.
5
Press to turn the weekly timer ON. (
* When the weekly timer is ON, the day of the week whose timer setting is complete, will light.
Press again to turn the weekly timer OFF. (
Timer ON. Change temp.
Timer OFF. Temp. setting: 27°C Temp. setting: 28°C
0 ： 30
7 ： 30 8 ： 30
8 ： 00
Wake up
SENSOR ABSENCE DETECTION
The sensor detects When no-one is in the room,
the floor temperature.... the unit automatically switches to
energy-saving mode.
10 minutes after
To avoid overcooling
person leaves room
To warm from the
60 minutes after
foot-level up
person leaves room
to select airfl ow direction.
(1) (2) (3) (4) (5) (SWING)
Heating (or Cooling) of two locations using
the double vane
Air
Dust
Virus Bacteria
Plasma
space
Neutralization/Sterilization
Air
.
lights.)
goes out.)
23 ： 30
Go to bed
INDIRECT/DIRECT
Press to activate INDIRECT/DIRECT
mode. This mode is only available when the
i-see control mode is effective.
(INDIRECT) (DIRECT) (OFF)
The unit monitors people......
Allowing
indirect airflow
Enhance comfort by averting airflow away from
people, or set direct airflow to target people for quick
cooling/heating.