Samsung SCP-3250H Installation Manual

Smart Dome Camera

Installation Guide

imagine the possibilities
Thanks you for purchasing this Samsung product.
To receive a more complete service, please visit
our website
www.samsungsecurity.com
2. Waterproof Installation
Precautions for waterproofing when installing the camera on the wall with a
1.
combination of "OUTDOOR HOUSING" and "WALL MOUNT ADAPTOR".
A. Install the "WALL MOUNT" on a vertical wall. Installation on a tilt wall may cause inflow of
moisture into the "OUTDOOR HOUSING" through the external cables.
B. Apply the sufficient "TEFLON TAPE" to the screws (1.5" NPT) present in the "HOUSING BODY".
C. Connect the external cables through the "BUSH" to the "HOUSING BODY".
(For more information about the connection, refer to the user manual of the "OUTDOOR
HOUSING".)
D. When mounting the "COVER DOME" onto the "HOUSING BODY", note that you should not
let the "GASKET DOME" loose from the "COVER DOME". Also keep in mind that the "O-RING"
for each "SCREW" (x3) should not be loose from the "SCREW" while fixing the "SCREW".
E. For waterproofing purposes, after inserting the "WALL MOUNT ADAPTOR", apply the
"SILICON SEALANT" between the wall and "WALL MOUNT", and around the borders.
(Pay special attention to the sealing when installing on an irregular surface.)
CONCRETE WALL
WALL MOUNT
BUSH
1.5" NPT PIPE
COVER DOME
SCP-3250H
SCP-2250H
SCP-2430H
SCP-3430H
SILICON SEALANT
USE TEFLON TAPE
HOUSING BODY
GASKET DOME
O-RING
SCREW

Installation Precautions

❚
1. CCTV equipment must be installed by an experienced service engineer.
Install the camera at a location that can support more than 4 times the total weight
2.
of the equipment.
3. Install the camera at a location free from mechanical vibration. When installing at a
location subject to mechanical vibration, be sure to install anti-vibration measures
before putting the camera in position.
Contents
❚
1. Protection Against Lightning Strikes
Waterproof Installation
2.
3. At a Glance
4. Connecting the adaptor cable
Cable Connection
5.
6. Communication Setup
1. Protection Against Lightning Strikes
For outdoor installations, a lightning rod must be installed above the camera to
1.
protect it from lightning strikes.
2. To avoid interference and prevent damage due to current surges, the camera's
grounding conductor must be separate from the lightning arrester's ground and
high-voltage ground.
Lightning generates great amounts of energy so that lightning rods cannot guarantee total
protection for the camera.
When installing a lightning rod, make sure that protection angle and minimum distance (2m)
Caution
between the lightning rod and the camera are properly implemented.
(Protection Angle "a" : Within 45°)
2. Precautions for waterproofing when installing the camera on the wall with a
combination of "OUTDOOR HOUSING" and "CEILING MOUNT ADAPTOR".
A. Apply the sufficient "TEFLON TAPE" to the screws (1.5" NPT) present in the "HOUSING BODY".
B. Connect the external cables through the "BUSH" onto the "HOUSING BODY".
(For more information about the connection, refer to the user manual of the "OUTDOOR
HOUSING".)
C. When mounting the "COVER DOME" onto the "HOUSING BODY", note that you should not
let the "GASKET DOME" loose from the "COVER DOME". Also keep in mind that the "O-RING"
for each "SCREW" (x3) should not be loose from the "SCREW" while fixing the "SCREW".
D. For waterproofing purposes, after inserting the "CEILING MOUNT ADAPTOR", apply the
"SILICON SEALANT" between the wall and "WALL MOUNT", and around the borders.
(Pay special attention to the sealing when installing on an irregular surface.)
CONCRETE CEILING
CEILING BOARD
BUSH
1.5" NPT PIPE
COVER DOME
Min. 2m
(Minimum height of the lightning rod)
SILICON SEALANT
CEILING MOUNT ADAPTOR
USE TEFLON TAPE
HOUSING BODY
GASKET DOME
O-RING
SCREW