Hayward ColorLogic LKCUS1100 Owner's Manual

IMPORTANT SAFETY
INSTRUCTIONS
WARNING – Before installing or servicing this elec-
trical equipment, turn power OFF at the circuit
breaker.
READ AND FOLLOW ALL
INSTRUCTIONS
WARNING – Read and follow all instructions in this
owner's manual. Failure to follow instructions can
cause severe injury and/or death.
WARNING – This product should be installed and
serviced only by a qualified professional.
CAUTION – All electrical wiring MUST be in con-
formance with all applicable local codes, regula-
tions, and the National Electrical Code (NEC).
ATTENTION INSTALLER – THIS MANUAL CONTAINS
IMPORTANT INFORMATION ABOUT THE INSTALLA-
TION, OPERATION, AND SAFE USE OF THIS PROD-
UCT THAT MUST BE FURNISHED TO THE END USER
OF THIS PRODUCT. FAILURE TO READ AND FOLLOW
ALL INSTRUCTIONS COULD RESULT IN SERIOUS IN-
JURY.
WARNING – Risk of Electric Shock. Hazardous volt-
age can shock, burn, and cause death or serious
property damage. To reduce the risk of electric
shock, do NOT use an extension cord to connect
unit to electric supply.
WARNING – To reduce the risk of electric shock, the
ground wire must be connected to the grounding
means provided in the electric supply panel with a
conductor equivalent in size to the circuit conduc-
tors supplying this equipment.
WARNING – Do not submerge the ColorLogic Light
Controller.
CAUTION – Do not connect two or more ColorLogic
Light Controllers together.
WARNING - To reduce the risk of injury, do not permit
children to use this product unless they are closely
supervised at all times.
WARNING - For indoor use only. This unit is not
intended for outdoor use unless mounted in a suit-
able UL rated weatherproof outlet box and cover.
SAVE THESE INSTRUCTIONS
USE ONLY HAYWARD GENUINE REPLACEMENT PARTS
Introduction
The Hayward Light Controller offers a dedicated solution
for controlling your ColorLogic LED pool and spa lights
from a convenient remote location. It's designed to install
into a standard wall electrical box and is wired to the high
voltage side of the ColorLogic light's transformer. Once
installed, the Light Controller can be used to fully control
your pool and spa lights. Turn lights on/off and change to
fixed colors or shows using the Light Controller's rotary
knob and front buttons.
Specifications
CSA enclosure type: Type 2, ENCL 2, or equivalent
Indoor electrical box: UL recognized single or multi gang
with minimum 14.0 in volume
3
Outdoor electrical box: UL recognized single or multi gang
with minimum 18.0 in volume
3
Compatibility
The Light Controller is compatible with the following
ColorLogic Low Voltage LED lights:
•
Universal ColorLogic Pool LED Light
•
Universal ColorLogic Spa LED Light
•
ColorLogic 320, 160, 80 and 40 LED Lights
Total allowable light wattage for the Light Controller is 300
watts. A combination of various lights can be used but
total wattage must not exceed 300 watts. Refer to your
ColorLogic light's power consumption when determining
how many lights to use with the Light Controller. An
example of combinations are shown below:
•
3 Pool Lights
•
2 Pool Lights and 1 Spa and/or Accent Light
•
1 Pool Light and 4 Spa and/or Accent Lights
•
6 Spa Lights
•
6 Accent Lights (320 model)
•
Any combination that does not exceed 300 watts
IMPORTANT: Add the individual wattage for each light
and do not exceed 300 watts.
Before you Begin
Set your ColorLogic lights to "UCL mode" BEFORE installing
the Light Controller (refer to your light's manual). If not in
"UCL mode", the ColorLogic lights will not operate properly
after the Light Controller is installed.
NOTE: The Light Controller requires a Neutral connection
to operate. If retrofitting into an existing installation, make
sure that the electrical box contains a Neutral connection.
Installation
Mounting Location
The Light Controller installs into a standard electrical
outlet box. When determining a suitable location, consider
that wiring from the Light Controller must connect to the
primary side of the light's low voltage transformer.
Note that the Light Controller is designed for indoor
use but can be mounted outdoors if a suitable UL rated
weatherproof outlet box and cover are used.
Wiring
Lever action terminal blocks are in-
cluded to aid in installation. Move
levers to the fully open position when
inserting wires. Close the levers to
lock the wires in place.
Connect the Light Controller's green wire to ground using
a lever action terminal block that is supplied. The Light
Controller comes with a plug-in wiring harness for easy
installation and removal. All wiring connections should
be made directly to the harness using the additional lever
action terminal blocks. After wiring is complete, the harness
can be plugged into the back of the Light Controller. It
can then be secured into the electrical box. Refer to the
following diagram for wiring connections.
Neutral in
from supply
(required)
Line out
&
to transformer
Line in
Neutral out
from supply
to transformer
white black
red
Ground in
from supply
&
Ground out
to transformer
green
Operation
After wiring is complete, turn on power at the circuit
breaker that is connected to Light Controller. The Light
Controller will initiate communication with the ColorLogic
lights. This may take a minute or two as the lights will
cycle between colors and finally default to the Voodoo
Lounge light show. The Light Controller will indicate this
in the PREVIEW WINDOW.
Refer to the following information for operation and control
of your ColorLogic lights.
Onboard pushbuttons
For best results, press on the outside of pushbuttons.
SHOW/COLOR -this is the default mode and
is used to control light shows and colors.
SCHEDULE - this is a programming mode and
is used to set a countdown timer or schedule.
USE ONLY HAYWARD GENUINE REPLACEMENT PARTS
RESYNC - use this button to resume connec-
tion with the ColorLogic lights if communica-
tion is interrupted.
ENTER - use this button to confirm a selection
while in SCHEDULE mode.
CENTER KNOB - To turn the lights on, briefly
push on the CENTER KNOB. To turn the lights
off, push in and hold for 3 seconds. To change
a show or color, rotate the CENTER KNOB to
the desired show/color and push the CENTER
KNOB briefly to save.
PREVIEW WINDOW - this is the LCD display
above the CENTER KNOB. The PREVIEW
WINDOW shows the color or light show that
has been selected via the CENTER KNOB. The
PREVIEW WINDOW will remain on 5 minutes
after the last user input.
Off & On
Turn the lights on by briefly pushing in the CENTER KNOB.
To turn off, push on the CENTER KNOB and hold for 3
seconds. The Light Controller may indicate that it's "busy"
by cycling through all LEDs in a circular pattern. This is
normal operation and occurs whenever the Light Controller
is busy processing a request. Let the Light Controller come
out of this state before continuing.
To Turn ON,
To turn OFF, hold
briefly push the
the CENTER
CENTER KNOB
KNOB for 3
seconds
Select Color or Show
To select a specific color or show, rotate the CENTER
KNOB to the desired selection. The PREVIEW WINDOW
will display the desired color/show. Briefly push CENTER
KNOB to save. The lights will change to the new selection.
1 2
Rotate CENTER
Briefly push the
KNOB to select
CENTER KNOB to
desired color or
save
show
If you try to save the same color or show that is currently
selected, the Light Controller will indicate that no change
will occur by blinking LED 1 (see LED Indicator Codes) and
remain in Show/Color mode.