Sealey TC180.V2 Instructions

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
refer to Wear eye
instructions protection
1. SafeTy
1.1.

elecTrical SafeTy

WarNiNG! it is the responsibility of the owner and the operator to read, understand and comply with the following:
‰
You must check all electrical products, before use, to ensure that they are safe. You must inspect power cables, plugs, sockets and
any other connectors for wear or damage. You must ensure that the risk of electric shock is minimised by the installation of appropriate
safety devices. A residual current circuit Breaker (rccB) should be incorporated in the main distribution board. We also recommend
that a residual current device (rcd) is used. it is particularly important to use an rcd with portable products that are plugged into a
supply which is not protected by an rccB. if in any doubt consult a qualified electrician. You may obtain a residual current device by
contacting your sealey stockist.
You must also read and understand the following instructions concerning electrical safety:-
a) the electricity at Work Act 1989 requires all portable electrical appliances, if used on business premises, to be tested by a qualified
electrician, using a Portable Appliance tester (PAt), at least once a year.
b) the Health & safety at Work Act 1974 makes owners of electrical appliances responsible for the safe condition of those appliances
and the safety of the appliance operators. if in any doubt about electrical safety, contact a qualified electrician.
ensure that the insulation on all cables and on the appliance is safe before connecting to the power
9
supply.
ensure that cables are always protected against short circuit and overload.
9
regularly inspect power supply cables and plugs for wear or damage and check all connections to ensure that
9
none is loose.
ensure that the voltage marked on the appliance matches the power supply to be used and that the plug is
9
fitted with the correct fuse - see fuse rating at right.
DO NOT pull or carry the appliance by the power cable.
9
DO NOT pull the plug from the socket by the cable.
8
DO NOT use worn or damaged cables, plugs or connectors. immediately have any faulty
8
item repaired or replaced by a qualified electrician. When an AstA/Bs approved uK
3 pin plug is damaged, cut the cable just above the plug and dispose of the plug safely.
fit a new plug according to the following instructions (uK only).
a) connect the Green/YelloW earth wire to the earth terminal 'e'.
b) connect the BroWn live wire to the live terminal 'l'.
c) connect the Blue neutral wire to the neutral terminal 'n'.
d) After wiring, check that there are no bare wires, that all wires have been correctly connected, that the cable outer
insulation extends beyond the cable restraint and that the restraint is tight.
double insulated products, which are always marked with this symbol
to rewire, connect the wires as indicated above - DO NOT connect either wire to the earth terminal.
1.2.

GeNeral SafeTy

familiarise yourself with the application, limitations and potential hazards of the tile cutter.
9
WarNiNG! disconnect the cutter from the mains power before changing accessories, servicing or performing any maintenance.
‰
the machine must only be serviced by a qualified person or service agent. contact your sealey dealer for information.
9
Place the cutter on a supporting surface strong enough to take the weight of the machine and work piece during operation.
9
Keep the work area clean and tidy and free from unrelated materials. ensure there is adequate lighting.
9
inhaling dust can be harmful - always wear respiratory protection and ensure that there is adequate ventilation.
9
maintain the cutter in good condition, check moving parts alignment regularly. Keep blade clean and in good condition.
9
replace or repair damaged parts. use recommended parts only. unauthorised parts may be dangerous and will invalidate the warranty.
9
WarNiNG! Keep all guards and holding screws in place, tight and in good working order. check regularly for damaged parts.
‰
A guard, or any other part, that is damaged must be repaired or replaced before the tool is next used. the safety guard is a
9
mandatory fitting when the cutter is used on premises covered by the Health & safety at Work Act.
Before commencing work, ensure the blade is mounted correctly, securely fastened and is compatible with the machine, spindle speed
9
and the material to be cut. never use a blade which is damaged, bent or warped. use only recommended blades.
remove adjusting keys and wrenches from the machine and the vicinity before turning it on.
9
machine operators must have received sufficient training and instructions as to the dangers posed by the cutter and the precautions to be
9
observed. operators must be under the supervision of a person who has a thorough knowledge and experience of the machine and the
© Jack sealey limited
instructions for
Tile cuTTer
model no:
Wear protective Wear safety
gloves footwear
Original Language Version
Tc180.V2
Wear protective Wear ear
clothing protection
, are fitted with live (brown) and neutral (blue) wires only.
Wear a mask
recommended fuse rating
5 Amp
tc180.V2 | issue 3 05/12/16