Canon imageCLASS MP390 Setup Manual

Thank you for purchasing the Canon imageCLASS MP390. To prepare your machine for use, please follow the instructions in
this Set-Up Guide before referring to any other documentation.
For
IMPORTANT
PC users
This side explains the setup procedure for use without connecting to a computer. <Check packed contents, install and adjust machine>
Setup procedures
Start Unpack
You can use the copy, photo print, fax functions.
Setup
flow
This side explains the setup procedure for use by connecting to a computer. <Install MP Drivers and Utility Software>
Setup procedures
You can use the print, PC fax, scan functions.
1
Carefully remove all
items from the box.
Hold the bottom side.
Unpack the Unpack the
machine. machine.
When removing the machine from the
box, take sufficient care not to drop it.
Check
the
MP390
contents.
NOTE
• A printer cable is not included. You must purchase a USB cable (less than 5 m) to connect your
machine to a computer.
• Please note that the items included with your machine may vary depending on the country of purchase.
Connect the Connect the
telephone telephone
line. line. Connect the telephone
line cord to the wall jack.
NOTE
Depending on the telephone line used, the method of connection differs. This machine has a function for automatically setting the telephone line type.
However, in the case of connecting to an ADSL modem, please set the telephone line type manually.
For details, see "Registering Information in Your Machine" of the User's Guide .
1
Remove all shipping tape
the exterior of the machine.
After removing the tape, remove the protective sheet.
Connect the
Connect the
power cord. power cord.
Set-Up Guide
Do not connect the USB cable until
USB cable."
Connect Connect Install Install
telephone line power cord print head ink tanks
Install MP Drivers Connect USB cable Install Utility Software
2 3
Remove the protective Place the machine on
material. a flat surface.
Do not grasp
the scan unit.
After removing the protective material, do not Be sure to hold the machine by the sides.
lift the machine by grasping the scan unit. Set nothing in front of the machine.
Ink tanks
Black BCI-24 Black
Color BCI-24 Color
Modular cable Print head
Power cord
Connect external devices as follows:
= Telephone line jack
= External device jack
You can connect an external
device (telephone or answering Telephone or answering machine
machine) if necessary.
Telephone
Machine
line
Built-in computer modem and telephone
Telephone
Machine
Machine
line
from
HT3-2147-000-V.1.0 2
, "Connect the
Load Align
print media print head
1
Install the Install the
End
print head. print head.
4
1
Set-Up Guide
User's Guide
Warranty
* The Setup CD-ROM
contains the MP Install the Install the
Drivers, as well as
the electronic
ink tanks. ink tanks.
manuals Software
Setup
Guide and Photo
CD-ROM
Application Guide .
Black
PC users, please
read these guides.
3
Close the inner cover.
Telephone or
answering machine
Swing it upward into place.
1
LINE TEL Telephone
Computer
Load Load
the print the print
media. media.
Next page Next page
Connect the power cord.
2
1
Approx. 15 seconds
2
Lift the scan unit until it Open the inner cover.
locks into place.
Lift the scan unit.
Click
If the paper output tray does not open, press
the Open button to open the paper output tray.
If you open the scan unit while the machine is
turned ON, the paper output tray will open.
5
Prepare the print head. Insert the print head.
Do not
touch!
Remove the protective cap and dispose of it.
2
Prepare the ink tanks. Insert the ink tanks.
Click
Do not
touch! Insert the black Push it in until
Remove the ink tank into it locks into place.
protective cap and dispose of it. the right slot.
4
Close the scan unit.
Click
Lower it into place.
2
Open the multi-purpose Load the print media.
tray.
1 Load the print media
with the print side face up.
2
Pull up the tray
2
extension until Pinch and adjust the
it stops. paper guide to the
1
width of the stack.
Open the tray.
3
Use [4 ] or [ e] to select the
language for the LCD q, then
press [OK] w.
1 2
If the message <PUT IN CARTRIDGE> appears,
go to procedure 4, "Install the print head."
3
Raise the lock lever.
The print head holder
2
moves to the center.
Touch only here!
Install here.
1 Raise this securely.
Open the inner cover.
6
Lower the lock lever.
Click
Lower the lock
lever until it locks into place.
Insert the color Incorrectly Correctly
installed installed
ink tank into
the left slot.
Click
3
Pull out the tray
extension of the
paper output tray.
Ensure the paper stack
Pull it out until it stops.
does not exceed paper
limit mark.
Rear side Rear side