Page 1
Service SR7005 / N1SG/N1B/U1B /K1B Manual AV Surround Receiver • For purposes of improvement, specifi cations and design are subject to change without notice. • Please use this service manual with referring to the operating instructions without fail. • Some illustrations using in this service manual are slightly different from the actual set.
Page 2
MARANTZ Parts for your equipment are generally available to our National Marantz Subsidiary or Agent. ORDERING PARTS : Parts can be ordered either by mail or by Fax.. In both cases, the correct part number has to be specifi ed.
SAFETY PRECAUTIONS The following check should be performed for the continued protection of the customer and service technician. LEAKAGE CURRENT CHECK Before returning the unit to the customer, make sure you make either (1) a leakage current check or (2) a line to chassis resistance check.
Page 4
NOTE FOR SCHEMATIC DIAGRAM WARNING: Parts marked with this symbol z have critical characteristics. Use ONLY replacement parts recommended by the manufacture CAUTION: Before returning the unit to the customer, make sure you make either (1) a leakage current check or (2) a line to chassis resistance check. If the leakage current exceeds 0.5 milliamps, or if the resistance from chassis to either side of the power cord is less than 460 kohms, the unit is defective.
TECHNICAL SPECIFICATIONS n HD Radio section n Audio Section (for U) –15 [FM](Note: μV at 75 Ω, 0 dBf = 1 x 10 • Power amplifi er Receiving Range : Rated output : [FM] 87.5 MHz – 107.9 MHz [AM]530 kHz – 1710 kHz Front : Usable Sensitivity : 125 W + 125 W (8 Ω, 20 Hz –...
Page 7
SURROUND MODE Service Jigs When you repair the printing board, you can use the following JIG (Extension cable kit). Please order to marantz Offi cial Service Distributor in your region if necessary. 8U-110084S : EXTENSION UNIT KIT : 1 Set...
Page 8
DISASSEMBLY • Disassemble in order of the arrow of the fi gure of following fl ow. • In the case of the re-assembling, assemble it in order of the reverse of the following fl ow. • In the case of the re-assembling, observe "attention of assembling" it. •...
About the photos used for descriptions in the DISASSEMBLY" section. • The direction from which the photographs used herein were photographed is indicated at "Direction of photograph: ***" at the left of the respective photographs. • Refer to the table below for a description of the direction in which the photos were taken. •...
Page 10
(2) Cut the wire clamp band, then disconnect the connector wires and FFC cable, then remove the screws. STYLE PIN : Loose N1001 STYLE PIN : Loose N4201 FFC cable FFC cable (3) Remove the screws. Direction of Direction of photograph: C photograph: D Please refer to "EXPLODED VIEW"...
Page 11
2. HEAT SINK ASSY Proceeding : CABINET TOP HEAT SINK ASSY → (1) Remove the screws. View from bottom (2) Cut wire clamp band, then remove the screws. Disconnect the connector wires. Direction of Direction of photograph: C photograph: D N1001 STYLE PIN : Loose...
Page 12
(3) Remove the screws. Direction of photograph: A (4) Cut the wire clamp bands, then disconnect the connector wires and FFC cable. Remove the screws, SUPPORT PWB. and the HDMI BRACKET. HEATSINK ASSY STYLE PIN : Loose CUSHION BRACKET N4905 STYLE PIN : Loose SUPPORT PWB.
Page 13
3. PCB REG CNT/PCB REG Proceeding : CABINET TOP HEAT SINK ASSY PCB REG CNT/PCB REG → → (1) Remove the screws. N model PCB REG (2) Disconnect the connector wires and connector board. CP102 CP104 REG CNT UNIT N2004 CP13A Direction of photograph: C Board to board...
Page 14
4. HDMI UNIT ASSY Proceeding : CABINET TOP HDMI UNIT ASSY → (1) Remove the screws, then remove the BACK PANEL and the HDMI BRACKET. U model Direction of photograph: A (2) Cut wire clamp band, then disconnect the connector wires and the FFC cables. Remove the screws and the SUPPORT PWB.
Page 15
(3) Cut the wire clamp band, then disconnect the connector wires. Remove the screw. HDMI UNIT ASSY N4905 Direction of photograph: C CP13A N2004 (4) Remove the screws and disconnect the connector. CP402 CP401 CP403 CP405 CP102 N4610 CP104...
Page 16
(5) Disconnect the connector wire, then remove the screws and the P.W.B HOLDER.. P.W.B. HOLDER CX102 (6) Remove the RAITING LABEL BASE, then remove the screws and P.W.B HOLDER. Remove the HDMI UNIT ASSY from the main unit. RAITING LABEL BASE P.W.B HOLDER View from bottom Please refer to "EXPLODED VIEW"...
Page 17
SPECIAL MODE Special mode setting button b Press the ON/STANDBY button to turn on while pressing both buttons A and B at the same time. Mode Button A Button B Contents Serial No. and fi rmware versions such as Main, Sub, DSP are Version display STATUS RETURN...
Page 18
1. μcom/DSP Version display mode 1.1. Operation specifi cations μcom/DSP version display mode: When started up, the version information is displayed. Starting up: With the "RETURN" and "STATUS" buttons pressed, press the "ON/STANDBY" button to turn the power on. Now, press the "STATUS" button to the display the 2nd item information on the FL Display. 1.2.
Page 19
o OSD Program : Upper O S D P R G : Lower * * * * * * * * * * * * Q0 O SD font data : Upper O S D D A T : Lower * * * * * * * * * * * * Q1 E thernet(DM860) 1st Boot Loader, Hardware ID : Upper...
Page 20
1.3. Error display See the following table for each "Error information" display and its contents (status). Display order is q , w , e , r , t . Condition State State q Sub-μcom NG No response from Sub-μcom S U B E R R O R w DIR NG No response from DIR...
Page 21
2. Errors checking mode (Displaying the protection history) 2.1. Operation specifi cations Error mode (Displaying the protection history): When started up, the error information is displayed. Starting up: ●All model commonness With the "STATUS" and "MENU" buttons pressed, press the "ON/STANDBY" button to turn the power on. The error (protection history display) mode is set.
Page 22
2.3. Clearing the protection history There are two ways to clear the protection history, as described below. (1) Start up the error (protection display) mode, display the error, then press and hold in the "ENTER" button for 3 seconds. Upper P R O T E C T H I S T O R Lower...
3. DUAL BACKUP MEMORY This product has a Dual Backup Memory function. The conventional Backup functions to memorize, in the EEPROM (U5302) in the circuit, a current setting of the moment the main power is turned off so that it can be restored when it is turned ON again.
Page 24
When you repair the printing board, you can use the following JIG (Extension cable kit). Please order to marantz Offi cial Service. Distributor in your region if necessary. Note: When the connection which is wrong in the JIG (EXTENSION UNIT KIT) is done it becomes cause of damage.
Page 25
(3) PCB HDMI is detached from the chassis, and it puts it into the state turned inside out. Please pave an insulation sheet that is larger than PCB HDMI under PCB. b Connect the ground point of PCB to the chassis with a ground lead or the like. PCB INPUT Ground lead PCB VIDEO...
Page 26
PCB SIDE CNT PCV FRONT CNT PCB INPUT Insulation sheet Connection table of Board to Board Ref. No. Ref. No. 11 pin SIDE CNT N4908 HDMI 25 pin SIDE CNT N4907 HDMI 19 pin CP105 FRONT CNT N4910 HDMI 17 pin CP106 FRONT CNT N4911...
ABOUT REPLACE THE MICROPROCESSOR WITH A NEW ONE When replaced of the U-PRO (Microprocessor) or the Flash ROM, confi rm contents of the following. s After PWB Name Ref. No. Description Remark replaced HDMI U5301 R5F64169DFD SOFTWARE: Main HDMI U5101 EN29LV160BB-70TIP SOFTWARE: Main ROM HDMI U5500 R5F3650KNFB...
Page 28
Even with a broadband connection to the Internet, approximately about 1 hour is required for the updating procedure to be completed. Once updating starts, normal operations on the SR7005 cannot be performed until updating is completed. Also, setting items of the GUI menu of SR7005 or setting items of the image adjustment may be initialized.
Page 29
Error Details of Error code Display Coping strategies Code Data acquisition failed (timed out) Check the network connection. C o n n e c t i o n f a i l when downloading Main CPU Carry out the update in an environment fi...
Page 30
Error Details of Error code Display Coping strategies Code Connection to DPMS failed when Check the network connection. S u b * * * m i n rewriting fi rmware such as Sub Carry out the update in an environment C o n n e c t i o n F a i l 5 2 CPU, DSP, FPGA, and PLD.
Page 31
Error Details of Error code Display Coping strategies Code O S D * * * m i n Failure to delete data before Turn the power off then back on. rewriting serial fl ash. Updating starts automatically. U p d a t i n g f a i l Failure to receive fi...
Page 32
Error Details of Error code Display Coping strategies Code Notifi cation of line congestion Check the network connection. E t h e r I M G * * * m i n via DPMS access when rewriting Carry out the update in an environment DM860 related fi...
Page 33
Device display when fi rmware updated Target of devide when fi rmware updated. Target of device Display Error cpde M a i n * * * m i n 10~15 Main 36~3C U p d a t i n g 50~52 S u b * * * m i n...
Page 34
2. How to update by DWF 2.1. Preparations before starting the operation2 (1) Personal Computer (Installed "DFW_0005_SR7005_(Rev.1.0.13)_exe"). (2) RS-232 cable (9P (Male), Straight). 2.2. Connection of the AV receiver (1) Confi rm the power on/off switch of the AV receiver is turning off. (2) Connect the RS-232C cable from PC with the AV receiver.
Page 35
2.5. Communication check (1) Click the “Check Comm.” button. (2) When connection is good, then you can see the “Communication check OK.” message. (3) If connection is not good, then you can see the “Communication error!” message. Please confi rm the following (a) Check the connection of the AV receiver and PC.
Page 36
2.6. Download the fi rmware (1) Click the "Load" button. (2) Download the fi rmware from the specifi ed download source to PC. 2.7. Complete the fi rmware updating (1) Click the “Update” button. (2) When writing of the fi rmware is completed, the power of this unit turns on automatically and you can see the “Update completed”...
Page 37
After completion of the updating operation, the new version number can confi rmed by starting up theSR7005 according to the following procedure. With the following operation, the SR7005 can be set to the Flash ROM Version-Number Confi emation mode. Turn on power switch while simultaneously pressing "STATUS" and "RETURN" buttons on the front panel. Every time the "STATUS"...
Page 42
ADJUSTMENT Audio Section Idling Current Required measurement equipment: DC Voltmeter 1. Preparation (1) Avoid direct blow from an air conditioner or an electric fan, and adjust the unit at normal room temperature 15 °C ~ 30 °C (59 °F ~ 86 °F). (2) Presetting •...
TROUBLE SHOOTING 1. POWER 1.1. Power not turn on Power not turn on. When the power turned on, does the FLD on the front Is the fuse blown? Refer to 1.2.Fuse is blown. panel light? Check for damage Is a DC 5V voltage output in the SMPS B'D Is a DC 5V voltage being when the cord supplying the...
2. Analog video MONITOR OUT (CVBS) output NG Input CVBS Input Function : SAT COMPONENT To A Not output MONITOR OUT (Component) output NG "Video Convert" is set to ON. Input CVBS Input COMPONENT Function : SAT Function : DVD To B...
Page 45
Input CVBS Check power supply voltage. V+5V : N2004-4pin REGULATOR B'D fl aw. V-5V : N2004-1pin Check on set value of each IC. HDMI B'D L4900 : Check I C communication HDMI B'D fl aw. waveforms. L4901 : Check I C communication waveforms.
Page 46
Input CVBS/COMPONENT Check input signal of VIDEO DECODER (U1100). Check signal detection. HDMI B'D HDMI B'D Input CVBS : to A V : L4920 V_L4903 : H(+3.3V) Input COPONENT : to C COMPONENT-Y : L4923 COMPONENT_L4902 : H(+3.3V) COMPONENT-Cb : L4922 COMPONENT-Cr : L4921 Check FRONT CONNECTOR B'D fl...
Page 47
Input COMPONENT Check of power supply voltage V+5V : N2004-4pin REGULATOR B'D fl aw V-5V : N2004-1pin Check on set value of each IC. HDMI B'D L4900 : Check I C communication HDMI B'D fl aw waveforms. L4901 : Check I C communication waveforms.
Page 48
3. HDMI/DVI. 3.1. No picture or sound is output No picture or sound is output. Check HDMI/DVI cable connection. There may be a problem with the HDMI/DVI (1) Is the HDMI/DVI cable properly connected? cable. Check connection. (2) Are you using an HDMI/DVI selector, repeater or a device for Disconnect everything and connect only the improving picture quality? HDMI/DVI cable to check...
Page 49
TV's operating instructions. The TV is defective. (13) Are the picture and sound output when a different TV is used? Check set (SR7005) (14) Is the set's input set to HDMI? Check set's input setting, referring to the Is the output setting of set corresponding to the connection of TV? set's operating instructions.
Page 50
The BD/DVD player does not recognize the connection with the set. (17) Is the "H"(3V-5V) signal outputted of HDMI connector (K1100/K1101/ K1102/K1001/K1002/K1003 : 19pin)? With the BD/DVD player connected, Check voltage of the HDMI The pattern and circuit from the HDMI connector for the input on the side on which the BD/DVD player is connector (K1100/K1101/K1102/K1001/ connected.
Page 51
Check operation of each device. (AMP source : VCR [i/p:OFF, MONITOR OUT: MONITOR1] / Video input of player : 480P / Connect the TV.) Check operation of U1002 (ADV3002). (23) Check power supply. The power supply circuitry is defective. Are 5V or 3.3V supplied to U1002 (each power supply pin)? (24) Check RESET.
Page 52
Check operation of U1601. (30) Check power supply. Is 1.2V supplied to C1632? The power supply circuitry is defective. Is 3.3V supplied to C1656? (31) Check RESET. The RESET circuitry (Q1600 and Is RESET waveform confi rmed in N1601 (1pin), when power is surrounding circuitry) or U1601 is defective.
Page 59
4. AUDIO 4.1. AUDIO CHECK AUDIO OUTPUT : NG INPUT SURROND MODE SOURCE CHECK1 Check ANALOG AUDIO BLOCK. ANALOG 2CH DIRECT ANALOG INPUT SURROND MODE SOURCE CHECK2 Check Digital AUDIO BLOCK. COAX or OPT Legacy(PCM or DolbyDigital or dts…) INPUT SURROND MODE SOURCE CHECK3...
Page 60
4.2. Power AMP (7CH AMP B'D) No sound is output. The protector operates. Is the power transistor open or short circuit? Replace the power transistor. 2SB1647/2SD2560 Is the emitter resistance of the power transistor open? Replace the emitter resistance. 0.47Ω Is the base resistance of the power transistor open? Replace the base resistance.
4.3. Analog audio No sound is output Is the voltage of ±8V supplied to The power supply of ±8V is repaired. SIDE CNT B'D CP6 13-16 pin? Is the audio signal transmitted to The power amplifi er is repaired. AUDIO B'D CN401? Connect the connectors properly.
Page 62
Checking the settings Set the IP address and other parameters properly. For a fi xed IP setting, check Are the SR7005's network settings correct? whether the IP address is redundant with that of other devices, and check whether the subnet mask setting is correct.
Page 63
Is the USB device compatible with the set? and iPod (Remove some models) are supported. Checking the set (SR7005) Is the wire of N4201 properly connected? Connect the wire properly. Is a voltage (5V) being supplied between pins 1 and 4 of Jack602...
Page 64
5.3. No picture or sound is output Checking the set (SR7005):(If no picture is output) Are video signals output from U4203 pin 27 (Y) and pin 24 (C)? You do not use the USB hub. Check the analog video circuit.
Page 65
CLOCK FLOW & WAVE FORM IN DIGITAL BLOCK Wave form CH1: D-DATA CH1: DATA CH2: fs CH3: 64fs CH1: DATA CH2: fs CH3: 64fs CH4: 256fs...
Page 66
BLOCK DIAGRAM CURRENT HEADPHONE OUT SR6005,SR7005 FEEDBACK AMP IC1003 (8U-210105) VOLUME AND INPUT SELECTOR R2A15220FP SR6005/7005 7.1CH FL-B/FL-H INPUT R-CH Audio Selction FR-B/FR-H DIRECT FL-A FR-A SPK OUT ANALOG INPUT SR6005 SBL/Z2L SR7005 SBL/Z2L/Z3L TO DSP SR6005 SBR/Z2R RELAY BLOCK...
Page 67
COMPONENT IN COMPONENT U2001(8U-110085) INPUT SELECT COMP3-Y TC4052 COMP3-Cb COMP3-Cr 2.2K Y/C MIX U1002(8U-110085) MAIN Y/C SR6005 ONLY ZONE2 Y/C SR7005 ONLY 2.2K COMP4-Y COMP4-Cb COMPONENT COMP4-Cr Z2 MONI. OUT DET. SR7005 ONLY NR6005/7005 SR7005 ETHERNET SR5005 CVBS MAIN OUT CVBS Z2 MONI.
Page 68
PQ012ENB GUI 1.2V XC3S400A SCPU+5V PQ018ENA VE 1.8V ADV7392 CEC3.3V ADV7840,ADV3002,AD8195 CEC3.3V PQ018DNA AVDD 1.8V ADV7840 D1.8V NET1.8V TCC8600(SR6005) D5V POWER DV1.8V ABT2015,ADV7511,K4T51163QG*2 CEC1.8V ADV7840 D1.2V1 NET1.2V DM860(SR7005) NET POWER D1.2V2 DA1.2V ADSP21367 DA POWER D1.0V DV1.0V ABT2015 DV POWER3...
Page 96
2M2(5) 1M (5) 270K OPEN 1M (5) 1M (5) MTZJ39B MTZJ39B MTZJ39B MTZJ39B MTZJ39B OPEN OPEN OPEN OPEN OPEN OPEN F101 F100 SR7005 SR5005 SR6005 SR7005 SR5005 SR6005 2A/250V 2A/250V 2A/250V 6.3A/250V 6.3A/250V 6.3A/250V 1.6A/250V 1.6A/250V 1.6A/250V 3.15A/250V 3.15A/250V 3.15A/250V...
Page 97
-8V_IN -8V_IN D144 1N4007 F108 CP104 -8V_IN -8V_IN T3.15AL/250V D140 1N4007 C147 CP101 CN101 100N(EB)-50V *OPTION TABLE SR5005 SR6005 SR7005 MODEL AREA OPTION_A NJM2388F05 NJM2388F09 NJM2388F09 NJM2388F09 OPEN NJM2388F09 NJM2388F09 OPEN NJM2388F09 NJM2388F09 NJM2388F09 OPTION_B NOT USE NOT USE OPTION_C...
Page 98
REG_SIRIUS_COMMON CNT 2/4 SIDE CONNECTOR TO RC-5 TO RC-5 PAGE 8(A4) PAGE 8(A1) OPTION A&B MODEL OPTION_B SR5005 SR6005 SR7005 C125Z2-15P C125Z2-19P OPTION_A IC109 PQ033DNA1ZPH U ONLY CP802 OPEN 10/50 10/50 M3.3V 232IMO IC1A:A 232OMI AZ4580MTR D/MGND TO HD RADIO...
Page 106
IN4Y Q1001 C1032 47/16 C1036 47/16 K1003 OPEN R1038 6P-PIN-JACK R1058 R1010 R1039 OPEN U1003 R1045 L1001 K1002 OPEN OPEN SR7005:OPEN 6P-PIN-JACK OPEN 10/6.3 IN4CB C1011 Q1002 R1059 R1011 OPEN SR7005_only SR7005_only K1002 6P-PIN-JACK 10/6.3 IN4CR C1012 SR5005 SR5005 SR5005...
Page 107
TO COMPONENT TO COMPONENT N3003 OPEN CB-G MONITOR CR-G MONIL1 LINE1 MONIL2 LINE2 MONIL3 LINE3 N3001 OPEN CB-G CR-G LINE1 VIN1L1 LINE2 VIN1L2 LINE3 VIN1L3 N3002 OPEN CB-G JAPAN LINEA LINEB ON CHANNEL CR-G Q3001 LINE1 VIN2L1 ASPECT_H OPEN VIDEO-2 LINE2 VIN2L2 LINE3...
Page 108
OPEN OPEN HPDF HPD/HEAC- KRC102S C21 0.1/10 KRC104S DDCDATA DDCCLK UTILITY/HEAC+ CE_Remote 0.1/10 R16 2.2K CKshield R17 OPEN 23P-FFC DOshield TXEN. TXEN. HPDF CE C D1shield DDC_SDA DDC_SCL HDMI5V D2shield CEC5V CEC3.3V OPEN DGND RX_C- RX_C+ RX_0- HDMI BRACKET RX_0+ OPEN RX_1- RX_1+...
Page 112
IPSCL IPSCL IPSDA IPSDA SR7005 only R1806 OPEN R1807 OPEN 1TXINT 1TXINT 1TXRST 1TXRST HDMI_A.SEL MONISEL MONISEL C1816 4.7/6.3 C1817 OPEN OPEN R1835 SR6005 only C1818 OPEN R1836 OPEN L1804 1TXVSYNC R1802 OPEN 1TXVSYNC CEC_CLK SR7005 only 1TXHSYNC 1TXHSYNC DVDD 1TXDE C1801 0.1/10...
Page 113
U2002 PQ033DNA1ZPH 50mA VOUT ON/OFF GN D DV5V DV3.3V L2000 R2010 DGND U2000 OPEN 10mA OPEN PQ018ENA1ZPH VEI2PCK 110mA VEI2PCK OUT 3 NC 4 VEI2VS VEI2VS VEI2HS VEI2HS VEI2C9 VEI2C9 VEI2C8 VEI2C8 VEI2C7 VEI2C7 VEI2C6 VEI2C6 VEI2C5 VEI2C5 VEI2C4 VEI2C4 VEI2C3 VEI2C3 VEI2C2...
Page 122
TO DM860 C4230 OPEN C4231 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 OPEN R4232 2 3 4 5 6 7 8 9 10 11 12 13 14 15 OPEN SRCMUTE SRCDATA C4232 SRCDATA OPEN SRC64fs...
Page 123
TO MAIN CPU NET3.3V DIGITAL NET1.8V SUPPLY DGND R4410 OPEN R4447 OPEN R4411 OPEN U4404 C4455 C4458 OPEN OPEN C4459 OPEN JTAG N4400 OPEN L4402 OPEN VSS2 R4431 OPEN TCKUSB CVDD MCLKUSB OPEN GND_D1 MCLK TDOUSB BCKoUSB BICK VSS1 Aout R 4433 SDTI OPEN...
Page 125
TO DIGITAL SUPPLY L5028 OPEN L5029 OPEN SWM5V REMOTE3.3V L5030 OPEN SWM3.3V L5031 OPEN L5032 OPEN M3.3V L5033 OPEN L5034 OPEN L5035 OPEN N4907 25P-SOCKET(C125Z2) L4927 OPEN D5V(MX) SWM5V(MX) SWM3.3V M3.3V DA+5V D/MGND DA+7V SIR_MO5/RDSDA L5005 OPEN SIR_MO/RDS_DATA DA-7V SIR_MI5/RDSCK L5006 OPEN SIR_MI/RDS_CLK...
Page 128
TO HDMI RX TO VIDEO ENCODER TO HDMI TX TO GUI PLD SCPU5V R5527 4.7 K SCPU3.3V R5528 4.7 K DGND R5529 4.7 K SUBBDOWN SUBBDOWN R5530 4.7 K PLDAERR. PLDAERR. MPLDCLK MPLDCLK MPLDDATA MPLDDATA MPLDCSMAIN MPLDCSMAIN SUBTCK DV_POWER1 SUBTMS CEC_POWER SUBTDI SUBTDO...
Page 129
CONNECT1 UNIT OPEN. OPEN. Q1011 Q1014 Q1015 Q1016 N1004 N1006 8P-TUCP-BASE N1009 KRC102S KRC102S KRC102S KRC102S 5P-PH OPEN OPEN 5P-PHs PLATE-EARTH-SR7005-A332 H/P-L H/P_L 8U-110100-7 C1025 C1026 B1011 C1018 H/P-R H/P_R S1025 N1005 R1016 POWER SW UNIT 1000P 1000P 446410049000M OPEN OPEN...
Page 130
WIRING DIAGRAM AC CORD FRONT WIDE B'D SIRIUS UNIT SPK UNIT 2P WIRE (FRONT.WIDE GND) DIGITAL UNIT 23P CARD CABLE (FRONT HDMI) 5P WIRE (DIGITAL PWR) VIDEO UNIT FRONT CNT UNIT AUDIO IN UNIT PREOUT UNIT (S4) MAIN TRANS REG_CNT UNIT (S2) (S1) REG UNIT...
Page 131
EXPLODED VIEW s (ONLY N1SG VER.) (ONLY U VER.) Bx24 Bx6(ONLY U VER.) 59 x2 Bx10 Fx21 WARNING: Parts marked with this symbol have critical characteristics. Use ONLY replacement parts recommended by the manufacturer.
Page 132
N1SG P1-5 SELECTOR UNIT SPRING DOOR SR7005 A332 OPT UNIT BRACKET DOOR SR7005 A332 H/P UNIT 422510037109M COVER DOOR INNER BL SR7005 A332 U1B,N1B,K1B DOORDET 422510037130M COVER DOOR INNER SG SR7005 A332 N1SG GUIDE L UNIT 422510036205M PLATE JACK BL SR7005 A332...
Page 134
CUSHION F SR7005 A332 533610073004M CUSHION R SR7005 A332 CABINET SHEET LABEL FOR PKG SG N1SG CONT LABEL SUB ASSY SR7005 (U) CONT LABEL SUB ASSY SR7005 (N) N1B, N1SG ★ 21 LABEL SIRIUS/HD RADIO SR7005 A332 ★ 22 LABEL LAST FM SR7005 A332...
Page 135
SEMICONDUCTORS Only major semiconductors are shown, general semiconductors etc. are omitted to list. The semiconductor which described a detailed drawing in a schematic diagram are omitted to list. 1. IC's R5F64169DFD (HDMI : U5301) (Note 1) IIO0_0 / IIO1_0 / D8 / P1_0 P4_4 / CS3 / A20 / CTS6 / RTS6 / SS6 AN0_7 / D7 / P0_7 P4_5 / CS2 / A21 / CLK6...
Page 136
R5F64169DFD Terminal Functions Pin Name Synbol I/O Type Pullup STBY stop Function 1 P96/(TXD4) SIRIUS RST O/L SIRIUS control pin 2 P95/(CLK4) HD RADIO RST/ST O/O/I C/C/- O/L HD RADIO control pin /ANALOG TUNER control 3 P94/(CTS4)/TB4IN RC-IN M3VPu O/L Remote control signal input 4 P93/(CTS3)/TB3IN Flasher IN O/L IR Flasher control signal input...
Page 137
Pin Name Synbol I/O Type Pullup STBY stop Function 59 VCC VCC2 60 P131 RST SUB O/L Output for reset of sub-μcom 61 P130 SCPU POWER O/L SUB CPU POWER ON/OFF switch(H:ON) 62 P53/BCLK BCLK O/L External memory access pin(NC) 63 P52/RD O/L External memory access pin(Connection:OE#) 64 P51/(WR1)/BC1...
Page 138
Pin Name Synbol I/O Type Pullup STBY stop Function 123 P157 ZVOL DATA O/L ZONE VOL(NJW1194) control 124 P156 E SPI REQ O/L ETHERNET communication control pin 232C CONTROL 125 P155/(RXD6) O/L SUB LOG MODE : For 232C course switch control (SUB LOG MODE) 126 P154/(TXD6) TUNED...
Page 140
R5F3650KNFB Terminal Functions Pu/Pd PURE Pin Name Synbol I/O Type Det P.OFF Function (Int.) (Ext.) STBY 1 P94 VSEL DATA VIDEO PLD control pin 2 P93 DIR CE DIR control pin (LC89058W-VF4A) 3 P92/SOUT3 DIR DIN DIR control pin (LC89058W-VF4A) 4 P91/SIN3 DIR DOUT DA3.3Pu...
Page 141
Pu/Pd PURE Pin Name Synbol I/O Type Det P.OFF Function (Int.) (Ext.) STBY 58 P32 DAC MDI DAC control pin (ASK4358) 59 P31 DAC MC DAC control pin (ASK4358) 60 VCC +3.3V 61 P30 DAC MS DAC control pin (ASK4358) 62 VSS 63 P27 DAC RST...
Page 143
AD8195ACPZ (HDMI : U1) 30 AVCC PIN 1 29 PE_EN INDICATOR 28 TX_EN 27 AVEE VTTI 26 AVCC AD8195 TOP VIEW 25 AVCC (Not to Scale) 24 AVEE 23 AVCC 22 AVCC AVCC 21 COMP NOTES 1. THE AD8195 LFCSP HAS AN EXPOSED PAD ON THE UNDERSIDE OF THE PACKAGE THAT AIDS IN HEAT DISSIPATION.
Page 147
IS42S32200E6TL Terminl Function Pin No. Signal Pin No. Signal Pin No. Signal Pin No. Signal DATA28 DATA27 IOVDD IOVDD ADDR0 SDCAS IOVDD ADDR2 SDRAS DATA26 ADDR1 SDCKE DATA25 ADDR4 SDWE DATA24 ADDR3 TRST DATA23 ADDR5 SDA10 IOVDD DATA22 SDCLK0 DATA21 IOVDD CLK_CFG0 DATA20...
Page 148
LC89058W-E (HDMI : U2805,U2806,U2807) 35 34 33 32 31 30 29 28 27 26 25 SDIN SLRCK SBCK RDATA XMODE RLRCK DGND LC89058W-E DV DD DV DD DGND GPIO0 RBCK RMCK GPIO1 AGND GPIO2 GPIO3 AV DD RXOUT2 * : Pull-down resistor internal at no selection Pin Functions RXOUT1 RX0-6 input S/PDIF through output pin 1...
Page 149
Pin No. Name Function DGND Digital GND DV DD Digital power supply (3.3V) XMCK Oscillation amplifier clock output pin XOUT Output pin connected to the resonator External clock input pin, connected to the resonator (12.288MHz/24.576MHz) DV DD Digital power supply DGND Digital GND MOUT...
Page 150
ADSP21367KSWZ2A (HDMI : U3200) PIN 1 INDICATOR TOP VIEW (PINS DOWN) ADSP21367KSWZ2A Terminal Function Pin No. Signal Pin No. Signal Pin No. Signal Pin No. Signal DATA28 DATA27 IOVDD IOVDD ADDR0 SDCAS IOVDD ADDR2 SDRAS DATA26 ADDR1 SDCKE DATA25 ADDR4 SDWE DATA24 ADDR3...
Page 152
W9864G2IH-6 Block diagram CLOCK BUFFER CONTROL SIGNAL GENERATOR COMMAND DECODER COLUMN DECODER COLUMN DECODER CELL ARRAY CELL ARRAY BANK #0 BANK #1 MODE REGISTER SENSE AMPLIFIER SENSE AMPLIFIER ADDRESS BUFFER DATA CONTROL CIRCUIT BUFFER DQ31 COLUMN REFRESH COUNTER COUNTER DQM0~3 COLUMN DECODER COLUMN DECODER CELL ARRAY...
Page 153
W9864G2IH-6 Pin description PIN NUMBER PIN NAME FUNCTION DESCRIPTION Multiplexed pins for row and column address. Row address: A0−A10. Column address: A0−A7. 24, 25, 26, 27, 60, 61, 62, Address A0−A10 A10 is sampled during a precharge command to 63, 64, 65, 66 determine if all banks are to be precharged or bank selected by BS0, BS1.
Page 154
EN29LV160BB (HDMI : U3202,U5101) BYTE# DQ15/A-1 DQ14 DQ13 Standa rd DQ12 TSOP RESET# DQ11 RY/BY# DQ10 EN29LV160BB Block Diagram RY/BY# DQ0-DQ15 (A-1) Block Protect Switches Erase V oltage Generato r Input/Output Buffers State Control Program Voltage Generato r Command Chip Enable Regi s ter Data Latch Output Enable...
Page 157
ピン配置 AK4358VQ (HDMI : U3803) LOUT1- AVSS LOUT1+ AVDD VREFH DZF3 ROUT4+ DZF2 AK4358VQ DZF1 ROUT4- CAD0 DIF0 DSDR3 ACKSN Top View DSDL3 BICK DSDR2 MCLK DSDL2 DVDD DSDR1 DVSS DSDL1 AK4358VQ Pin Function Pin Name Function LOUT1- DAC1 Lch Negative Analog Output Pin LOUT1+ DAC1 Lch Positive Analog Output Pin DZF3...
Page 158
DSDL3 DAC3 DSD Lch Data Input Pin DSDR3 DAC3 DSD Rch Data Input Pin DIF0 Audio Data Interface Format 0 Pin ROUT4- DAC4 Rch Negative Analog Output Pin ROUT4+ DAC4 Rch Positive Analog Output Pin VREFH Positive Voltage Reference Input Pin AVDD Analog Power Supply Pin, +4.75 +5.25V AVSS...
Page 159
HY27UF081G2A-TPCB (HDMI : 3901) HY27UF081G2A-TPCB Pin Function Pin Name Description DATA INPUTS/OUTPUTS IO0-IO7 The IO pins allow to input command, address and data and to output data during read / program IO8-IO15(1) operations. The inputs are latched on the rising edge of Write Enable (WE). The I/O buffer float to High-Z when the device is deselected or the outputs are disabled.
Page 161
W9825G6EH-6J (HDMI : U3902) DQ15 DQ14 DQ13 DQ12 DQ11 DQ10 LDQM UDQM A10/AP W9825G6EH-6J Block Diagram CLO CK BUFFER CO NTRO L SIG NAL G ENERATO R CO MMAND DECO DER CO LUMN DECODER COLUMN DECO DER CELL ARRAY CELL ARRAY BANK #1 BANK #0 MO DE...
Page 162
W9825G6EH-6J Pin Description PIN NUMBER PIN NAME FUNCTION DESCRIPTION Multiplexed pins for row and column address. 23 26, 22, A0 A12 Address 29 36 Row address: A0 A12. Column address: A0 A8. Select bank to activate during row address latch time, or 20, 21 BS0, BS1 Bank Select...
Page 165
SA7121 (HDMI : U4203) 33 V SSA2 res. V SSA1 V DDA3 CVBS V SSD1 res. SAA7120 V DDD1 V DDA2 SAA7121 RCV1 res. RCV2 V DDA1 res. MBH790 SA7121 Block Diagram V DDA1, handbook, full pagewidth RCV1 TTXRQ XTALO V DDA2 , V DDA4 V DDA3...
Page 166
SA7121 Pin Description SYMBOL DESCRIPTION − res. reserved test pin; connected to digital ground for normal operation test pin; connected to digital ground for normal operation line-locked clock; this is the 27 MHz master clock for the encoder digital ground 1 SSD1 digital supply voltage 1 DDD1...
Page 173
PARTS LIST OF P.W.B. UNIT s zParts for which "nsp" is indicated on this table cannot be supplied. zThe parts listed below are for maintenance only, might differ from the parts used in the unit in appearances or dimensions. Note: The symbols in the column "Remarks" indicate the following destinations. U : North America model N : Europe model K : China model...
Page 182
Ref. No. Part No. Part Name Remarks Q'ty C506 00D2544723922 CE04W1H101MT(GR) C507,508 132050044506S CK45B2H471KT C509 CK73B1H222KT +2125 C511,512 00D2544726932 CE04W2A100MT(GR) C513,514 00D2544716926 CE04W0J331MT(GR) C515 00D2544718937 CE04W1C470MT(GR) OTHERS PARTS GROUP BKT40 M3 SIDE TERMINAL CN404 5P 250mm 20010HS-CKM2002HV CP401 13P BASE(STRAIGHT) CP402 5P BASE(5267) CP403...
Page 183
SPK/SMPS P.W.B UNIT ASSY Ref. No. Part No. Part Name Remarks Q'ty SEMICONDUCTORS GROUP z IC100 00D2623047008 PC123Y22 z IC102 231010091708S TOP258MG IC116 212050010508S KIA2431AP Q001-007 00D2690184907 KRA102S-RTK/P (10K-10K) Q008-014 00D2690192902 KRC102S-RTK/P (10K-10K) Q020 00D2690184907 KRA102S-RTK/P (10K-10K) Q021 00D2690192902 KRC102S-RTK/P (10K-10K) TR100-102 00D2730468907 KTC3199-GR-AT/P...
Page 184
Ref. No. Part No. Part Name Remarks Q'ty CAPACITORS GROUP z D102 00D2538022707 CK45F2EAC103MC z D104 00D2538022707 CK45F2EAC103MC C001 133050083504S CQ93M2A473JT(PEF) C002 CK73B1H222KT +1608 C003,004 133050083504S CQ93M2A473JT(PEF) C005 CK73B1H222KT +1608 C006 133050083504S CQ93M2A473JT(PEF) C007 CK73B1H222KT +1608 C008,009 133050083504S CQ93M2A473JT(PEF) C010 CK73B1H222KT +1608 C011,012...
Page 185
Ref. No. Part No. Part Name Remarks Q'ty C112 134050106509S CE04W1H100MT(NXA) C113 CK73B1E104KT +1608 z C115 00D2538029700 CK45F2EAC222MC (KX) C116 CK73B1E104KT +1608 z C117 00D2538022707 CK45F2EAC103MC C118 CK73B1E104KT +1608 C119 134050107502S CE04W1E470MT(NXA) C120-123 CK73B1E104KT +1608 OTHERS PARTS GROUP BKT1 BRACKET PCB MTG BKT10 M3 TAP SIDE TERMINAL BKT2...
Page 186
Ref. No. Part No. Part Name Remarks Q'ty z RLY1 682010021000S RELAY(BC3-12) z RLY2-8 682010020007S G5PA-28-MC DC12 z T100 102010022002S SW TRANS(ST-4430A) WIRE1 1P BLK + 1P RED 200 mm SIN(105 Degree) WIRE3 1P 100mm SIN WIRE4 1P 80mm SIN WIRE5 2P TWIST 900mm B1813TOP WIRE CLAMPER...
Page 187
FRONT P.W.B UNIT ASSY Ref. No. Part No. Part Name Remarks Q'ty SEMICONDUCTORS GROUP D1001 263010045504S BL-BVT201G D1002,1003 00D2760704903 1SR35-400A(T93X) D1004 00D2760760989 MTZJ7.5B T77 D1016 00D2760761975 MTZJ18B T77 D1017 00D2760762903 MTZJ24B T77 D1018-1020 251310004507S CG0603MLC-12LE D1026 00D2760760947 MTZJ5.1B T77 D1027,1028 263010046507S BL-BUF4V5K-1-AV-FP3.5-TBF19.5C D1029,1030...
Page 194
Ref. No. Part No. Part Name Remarks Q'ty C4146 CC73CH1H330JT +1608 C4147,4148 CC73CH1H101JT +1608 C4149 00D2544722981 CE04W1H100MT(GR) C4150 CK73B1H472KT +1608 OTHERS PARTS GROUP CX3001 13P SOCKET(C125Z2) CX3003 15P SOCKET(C125Z2) CX3002 17P SOCKET(C125Z2) CX3000 19P SOCKET(C125Z2) CX4003 19P CON.PLUG(TWG-P) CX4002 15P PLUG(C125Z1) CX4001 17P PLUG(C125Z1) CX4000...
Page 195
DIGITAL P.W.B UNIT ASSY Ref. No. Part No. Part Name Remarks Q'ty SEMICONDUCTORS GROUP DSP ROM SUB ASSY U3202 8R2481004600S (EN29LV160BB-70TIP) DM860 ROM SUB ASSY U3901 (NAND01GW3B2CN6E) MAIN CPU ROM SUB ASSY U5101 8R2481004500S EN29LV160BB-70TIP MAIN CPU SUB ASSY U5301 8R2431004800S (R5F64169DFD) SUB CPU SUB ASSY...
Need help?
Do you have a question about the SR7005 and is the answer not in the manual?
Questions and answers