Panasonic KT4 series Instruction Manual page 17

Control output (OUT1)
Relay contact : 1a, Control capacity
Non-contact voltage (For SSR drive): 12
DC current
A1 output
Action
Hysteresis
Output
Control action
PID action (with auto-tuning function)
PI action: When derivative time is set to 0
PD action (with auto-reset function): When integral time is set to 0
P action (with auto-reset function): When both derivative and integral times are set to 0.
ON/OFF action: When proportional band is set to 0 or 0.0
OUT1 proportional band : 0 to 1000
Integral time
Derivative time
OUT1 proportional cycle : 1 to 120sec (Not available for DC current output type)
ARW
OUT1 output hysteresis : 0.1 to 100.0
OUT1 output limit
Circuit insulation configuration
Insulation resistance : 10M
Dielectric strength
Supply voltage
Allowable voltage fluctuation: 100 to 240V AC: 85 to 264V AC,
Power consumption
Ambient temperature : 0 to 50
Ambient humidity
Weight
External dimension
Material
Color
Attached function
[Input abnormality indication]
Output status
Contents and
selection when
Indication
input abnormal
Overscale
Measured value
has exceeded
Indication range
high limit value.
"
Underscale
Measured value
has dropped below
Indication range low
limit value.
"
Only for DC input and DC current output type, [Output status selection when input abnormal] is
available. For other inputs and outputs except for DC input and DC current output, the output status
will be the same one as when OFF is selected during [Output status selection when input abnormal].
For manual control, the preset MV (manipulated variable) is outputted.
Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email: info@clrwtr.com
: 0 to 5V DC, 1 to 5V DC, 0 to 10V DC Input impedance (100k
Allowable input voltage (15V or less)
Allowable signal source resistance (100
Electrical life, 100,000 cycles
: 4 to 20mA DC, Load resistance, maximum 550
: ON/OFF action
: 0.1 to 100.0
: Relay contact, 1a
Control capacity, 3A 250V AC (resistive load)
Electrical life, 100,000 cycles
(ON/OFF action when set to 0 or 0.0)
: 0 to 1000sec (OFF when set to 0)
: 0 to 300sec (OFF when set to 0)
: 0 to 100%
: 0 to 100% (DC current output type: –5 to 105%)
1
Power
Power
supply
2
3
A1
4
EVT (A2, Heater burnout
5
alarm) or OUT2
or more, at 500V DC
: 1.5kV AC for 1 minute between input terminal and power terminal
1.5kV AC for 1 minute between output terminal and power terminal
: 100 to 240V AC
: Approx. 8VA
(32 to 122 )
: 35 to 85%RH (no condensation)
: Approx. 200g
: 48 x 48 x 96.5mm (W x H x D)
: Flame-resistant resin (Case)
: Ash gray (Case)
: [Set value lock], [Sensor correction], [Auto/manual control switching],
Direct action
ON (20mA) or
OUT1 high
limit value
OFF (4mA) or
OUT1 low
limit value
" flashes.
OFF (4mA) or
OUT1 low
limit value
" flashes.
3A 250V AC (resistive load)
1A 250V AC (inductive load cosø= 0.4)
V DC maximum 40mA (short circuit protected)
+2
0
( ), or 1 to 1000
(2000 ), 0.0 to 999.9
( ), or 1 to 1000
Insulation
CT
11
input
12
Commu-
nication
50/60Hz, 24V AC/DC 50/60Hz
Output status
OUT1
Reverse action
OFF (4mA) or
OUT1 low limit
value
ON (20mA) or
OUT1 high
limit value
OFF (4mA) or
OUT1 low limit
value
or less)
( ) or 0.0 to 100.0%
Output
13
Input
14
CPU
15
24V AC/DC: 20 to 28V AC/DC
OUT2
Direct action
Reverse action
ON or
OUT2 high limit
OFF or
value
OUT2 low limit
OFF or
value
OUT2 low limit
value
ON or
OUT2 high limit
OFF or
value
OUT2 low limit
OFF or
value
OUT2 low limit
value
or more)
6
7
8
9
10