Product Specifications 1-2 Product Specifications (VP-D73/D73i/D75/D75i/D76/D76i/D77/D77i) Design and specifications are subject to change without notice. Operation Description SYSTEM Video signal PAL, CCIR standards Video recording system 2rotary heads,helical scanning system Audio recording system Rotary heads, PCM system Usable cassette Digital video tape (6.35mm width): MiniDV cassette Tape speed SP : approx.
2. Disassembly and Reassembly 2-1 Cabinet and PCB 2-1-1 Top Cover removal (1) Remove 2 screws Fig. 2-1 Top Cover removal Samsung Electronics...
Page 7
Disassembly and Reassembly 2-1-2 Ass’y Cover Housing removal (3) Remove cover housing in the direction of arrow (1) Remove 2 screws (2) Remove 2 screws Fig. 2-2 Ass’y Cover Housing removal Samsung Electronics...
Page 8
Disassembly and Reassembly 2-1-3 Ass’y Front removal (1) Remove 1 screw (3) Remove ass’y front in the direction of arrow (2) Remove 1 screw Fig. 2-3 Ass’y Front removal Samsung Electronics...
Page 9
Disassembly and Reassembly 2-1-4 Ass’y Case-Left removal (2) Remove 2 screws (1) Remove 2 screws (5) Remove ass’y case left in the direction of arrow (4) Remove 2 screws Fig. 2-4 Ass’y Case-Left removal Samsung Electronics...
Page 10
Disassembly and Reassembly 2-1-5 Ass’y Case-Right removal (1) Remove 2 screws (4) Remove ass’y case right in the direction of arrow (2) Remove 2 screws (3) Remove 1 screw Fig. 2-5 Ass’y Case-Right removal Samsung Electronics...
Page 11
Disassembly and Reassembly 2-1-6 Ass’y Rear removal (2) Remove ass’y rear in the direction of arrow (1) Remove 2 screws Fig. 2-6 Ass’y Rear removal Samsung Electronics...
Page 12
Disassembly and Reassembly 2-1-7 Ass’y Camera & Main PCB removal (2) Remove ass’y camera & main pcb in the direction of arrow (1) Remove 3 screws Fig. 2-7 Ass’y Camera & Main PCB removal Samsung Electronics...
Page 13
Disassembly and Reassembly 2-1-8 Ass’y-Camera removal (2) Remove 1 screw (3) Remove ass’y camera in the direction of arrow (1) Desolder Fig. 2-8 Ass’y Camera removal Samsung Electronics...
3. When changing the adjustment item after the adjusted value is designated, press the "START/STOP" button. SP PLAY 0:00:00:01 NO MODE EVR EPR Indicates preset values 1 V-REF Indicates the adjusted values S64 LOO Indicates current adjustment item. 01 01380 Samsung Electronics...
Page 17
Fig.1. RIGHT CASE Fig.2. REMOCON KEY STEP 3 . If you want to finish the adjustment mode, you have to do Power Reset. The Power Reset means that you pull out the power source and pull in it again. Samsung Electronics...
Page 18
DUB REC CURRENT DUBCUR * MODEL OPTION Model Adj.value Model Adj.value VP-D75i / SCD75 VP-D73 VP-D76i SCD73 / VP-D73i VP-D77i VP-D75 SC-D77 VP-D76 / VP-D77 2. How to adjust Video-Reference (V-REF). 1) Connect video output cable to wave form scope. The wave form scope must be connected to monitor.
Page 19
1) Select ZOOMVR in the video adjustment mode. 2) Adjust ZOOM SW so that the switch is put in the middle of T and W. 3) Adjust ZOOMVR so that the current value of ZOOM SW is equal to the adjusted ZOOMVR value. Samsung Electronics...
3. Press the Address selection button(START/STOP button) to skip the next address in order to finish the adjustment and store data. After finishing the adjustment, you have to do power reset. The PRML BER will be set to the right adjustment when shipping out video camera and PCB ASSY from factory. Samsung Electronics...
Page 21
The optimum means the number error is less than 10 EA. ;Current D73/D75/D76/ D77 manufacturing standard If the minimum value is as the followings, designate as the right values......................;Selection valueless iess than 18 ..................18 ;REG12===24A ......................19 ;REG12===26A ......................20 ;REG12===28A Samsung Electronics...
Page 22
......... ;REG24 ===FA2 6) Check the value is input to unit correctly. Samsung Electronics...
2) Press the "START/STOP" button when storing confirmed adjustment value of each adjustment step in EEPROM. 3) There is a flicker on screen after finishing each adjustment step. 4) To clear the adjustment mode, pull out the power source. Samsung Electronics...
Page 24
5 seconds. 3) Set the "POWER(CAMERA/PLAY- ER)" switch to "CAMERA" position. STEP 3 4) The OSD appears. Monitor OSD shows "16D XX XX". Then camera adjustment mode has Note : "XX" indicates variable values. been activated successfully. Samsung Electronics...
Page 38
Adjustment and Adjustment Addr. NTSC NAME Samsung Electronics 3-23...
Page 39
5) Press the FF(Mode Up)/REW(Mode Down) button so that OSD shows "260 XX XX". 6) Press the START/STOP (Confirm) button. Never impact on the lens when adjusting zoom and focus lens. There's is a flicker on screen after finishing the adjustment. 2.5m +/-1Cm 3-24 Samsung Electronics...
Page 40
Store max. and min. value of in 167and 6) Press the START/STOP (Confirm) button. 168 respectively. 7) There's is a flicker on screen after finishing the 6) There's is a flicker on screen after finishing the adjustment. adjustment. 95IRE 95IRE Samsung Electronics 3-25...
Page 41
1) Camera mode & 3100˚ K gray scale chart 2) Connect a video output terminal to a vec- torscope and a TV. 3) Press the FF(Mode Up)/REW(Mode Down) button so that OSD shows "70 XX XX". Samsung Electronics 3-26...
Page 42
1500-2000 Lux. 5) Press the PLAY (Data Up)/STOP (Data Down) so that the yellow level is 50IRE. 6) Press the START/STOP (Confirm) button to store data. 7) There's is a flicker on screen after finishing the adjustment. Samsung Electronics 3-27...
Page 43
1500-2000 Lux. 5) Press the PLAY (Data Up)/STOP (Data Down) so that the cyan vector is 284˚ . 6) Press the START/STOP (Confirm) button to store data. 7) There's is a flicker on screen after finishing the adjustment. 3-28 Samsung Electronics...
Page 44
FF (Mode Up) Shift adjustment address to right. REW (Mode Down) Up value. PLAY (Data Up) Down value. STOP (Data Down) Note: In service adjustment mode, button names are different from those in customer function control mode. 3-29 Samsung Electronics...
Page 45
Connect an voltmeter to TP-VCOM. c) Adjust the EVR so that DC voltage is DC 1.1±0.05 V. Note: In LCD adjustment mode, when shorting "A" of PCB to GND and pressing the START/STOP button, EEPROM stores con- firmed adjustment value. Samsung Electronics 3-30...
Page 46
Adjust the EVR so that Sync tip level is 4.2 Vp-p. 6) B-W/B a) TP-B & EVR b) Connect an oscilloscope probe to TP-B. c) Adjust the EVR so that Sync tip level is 4.4 Vp-p. Sync Tip Level Samsung Electronics 3-31...
Page 47
3-5-2. EVF adjustment 1) VIDEO GAIN a) Connect an oscilloscope probe to TP-V. b) Adjust the VRE02 so that A level is 2.5 Vp-p Remote Control Button Location 10 PIN CON. 2 PIN CON. Location of Test Point 3-32 Samsung Electronics...
Page 48
FF (Mode Up) Shift adjustment address to right. REW (Mode Down) Up value. PLAY (Data Up) Down value. STOP (Data Down) Note: In service adjustment mode, button names are different from those in customer function control mode. Samsung Electronics 3-33...
Page 49
TINT fix initial value GAMMA fix initial value R WB fix initial value LIMIT CONT fix initial value R BRT fix initial value fix initial value B BRT COM GA fix initial value fix initial value BRIGHT 3-34 Samsung Electronics...
Exploded View and Parts List 4-5 CASE LEFT ASSY Samsung Electronics...
Page 58
Description and Specification Reamrk AD63-00065C COVER-LI BATT AD97-03981A ASSY-LEFT SNA / SCD73 AD97-03794A SNA / SCD75 AD97-03795A SNA / SCD77 AD97-03796A SNA / VP-D73 AD97-03951A SNA /VP-D73i AD97-03797A SNA /VP-D75 AD97-03952A SNA /VP-D75i AD97-03798A SNA /VP-D76 AD97-04052A SNA /VP-D76i AD97-03799A...
Schematic Diagrams 8-20 USB / DSC Samsung Electronics 8-21...
Page 118
표지 영문 2001.7.4 2:0 PM 페이지1 DIGITAL COMCORDER DECK CSM-2000 ◈ File with the SERVICE MANUAL. DIGITAL CAMCORDER DECK CONTENTS 1. Operation 2. Adjustment 3. Disassembly and Reassembly...
Page 119
표지 영문 2001.7.4 2:0 PM 페이지2 E L E C T R O N I C S Ⓒ Samsung Electronics Co., Ltd. APR. 2001 Printed in korea AD68-30200A...
Page 120
❸ GEAR WHEEL ❿ IDLER LEVER EJECT ❹ GEAR MODE SWITCH HOLDER FPC SUB REEL DISK T ❺ GUIDE TENSION CAM DRUM BRAKE PULLY ❻ ARM TENSION MOTOR CAPSTAN SWITCH MIC ❼ BRAKE TENSION REVIEW ARM BRAKE MAIN T Samsung Electronics...
Page 121
MOTOR CAPSTAN GEAR WHEEL ❹ GEAR MODE SWITCH GUIDE RAIL ❺ GUIDE TENSION CAM GEAR CAPSTAN ❻ POLE BASE S ARM PINCH ❼ SLIDE MAIN POLE BASE T ❽ GEAR CAM MAIN TIMMING BELT ❾ LEVER CAM GEAR PULLY Samsung Electronics...
Page 122
Idler Rotate and stop in loading mode LD 2 70°~ 140.8° Capstan Rotate in unload mode STOP 199.89°~ 207.85° stop PLAY 269.3°~ 288.5° In REC/PB/CUE/FF/PAUSE ※ Fig is based Eject Mode. common signal 1 signal 2 Fig 1-3 Samsung Electronics...
Page 124
LD 1 ↓ Lever Cam ➍ rotates. LD 2 ↓ Chassis Sub ➏ moves. STOP PLAY MOTOR LOADING ➊ GEAR WHEEL ➋ GEAR MODE SWITCH ➌ GEAR CAM MAIN ➍ LEVER CAM ➎ SUB CHASSIS ➏ Fig 1-5 Samsung Electronics...
Page 125
LD 1 ↓ Brakes S ❹ released or operated to Reel Disk S ❺ by slide Main ❸. LD 2 STOP MOTOR LOADING ➊ SLIDE MAIN ❸ REEL DISK S ❺ BRAKE S ❹ CHASSIS SUB ❷ Fig 1-6 Samsung Electronics...
Page 126
Brake T ❹ released or operated to Reel disk T ❺ b y LD 1 slide Main ❸ LD 2 STOP MOTOR LOADING ➊ ➌ SLIDE MAIN CHASSIS SUB ➋ ➍ BRAKE MAIN T ➎ REEL DISK T Fig 1-7 Samsung Electronics...
Page 127
❾ of Gear Mode Switch ❽. STOP PLAY MOTOR LOADING ❶ ARM TENSION ❻ GUIDE TENSION CAM ❸ CAM CURVE A ❹ SPRING TENSION ❺ CAM CURVE B ❾ GEAR MODE SWITCH ❽ BRAKE TENSION ❼ CHASSIS SUB ❷ Fig 1-8 Samsung Electronics...
Page 128
Pinch Roller ❻ released from shaft of Motor Capstan ❼ by spring force of spring Lever pinch ❽. MOTOR LOADING ❶ MOTOR CAPSTAN ❼ PINCH ROLLER ❻ ARM PINCH ❹ SPRING LEVER PINCH ❽ SLIDE MAIN ❺ CAM CURVE A ❸ CHASSIS SUB ❷ Fig 1-9 Samsung Electronics...
Page 129
Arm Review ❺ simultaneously rotates clockwise and translates via cam curve ❹ of Chassis Main ❸ LD 1 LD 2 STOP PLAY MOTOR LOADING ❶ CHASSIS MAIN ❸ ARM REVIEW ❺ CAM CURVE ❹ CHASSIS SUB ❷ Fig 1-10 Samsung Electronics 1-10...
Page 130
MOTOR LOADING ❶ BASE DRUM GEAR WHEEL ❷ GEAR LOADING S ❻ GEAR MODE SWITCH ❸ GEAR LOADING T ❼ POLE BASE S ❽ POLE BASE T ❽ GEAR CONNECTOR ❺ GEAR CAM MAIN ❹ Fig 1-11 1-11 Samsung Electronics...
Page 131
↓ Reel Disk T ❻ or Reel Disk S ❼ rotates. DRUM MOTOR CAPSTAN ❶ GEAR CAPSTAN ❷ BELT TIMMING ❸ GEAR IDLER ❺ REEL DISK S ❼ REEL DISK T ❻ GEAR PULLY ❹ Fig 1-12 Samsung Electronics 1-12...
Page 132
By Lever lock ❻ pushed Lever Eject ❼ and turns on S/W Cassette-in ❽. COVER STOPPER ❷ CATCH ❶ KEY RELEASE ❸ LEVER LOCK ❻ LEVER EJECT ❼ CHASSIS SWITCH C-In ❽ SUB CATCH ❺ FIG 1-13 1-13 Samsung Electronics...
Page 133
Main moves to right. Pinch Roller rotates Brake S,T are via Silder Main and operated by Main Motor Loading detaches from Silde and contact rotates reverse Drum stops. Capstan Shaft. Reel S,T for braking Motor Capstan stops. and then stops. Samsung Electronics 1-14...
Page 134
SWITCH MIC HOLDER FPC SUB MOTOR LOADING MOTOR CAPSTAN GEAR WHEEL GEAR MODE SWITCH GEAR CAPSTAN ARM PINCH GUIDE TENSION CAM GEAR CAM MAIN SLIDE MAIN GEAR PULLY LEVER CAM DRUM BRAKE S BRAKE T Fig 1-14 1-15 Samsung Electronics...
Page 135
Gear Capstan, Belt Timing, Gear pully Gear Idier rotate in order. Reel S rotates. Reel T rotates. ✽ Tape is fed by the winding operation of Motor Capstan. → ARM TENSION Gear Mode switch cam Fig 1-15 Samsung Electronics 1-16...
Page 136
BRAKE PULLY BRAKE S SWITCH MIC BRAKE MAIN T HOLDER FPC SUB MOTOR LOADING MOTOR CAPSTAN GEAR WHEEL GEAR MODE SWITCH GEAR CAPSTAN GUIDE TENSION CAM GEAR CAM MAIN SLIDE MAIN GEAR PULLY LEVER CAM fig 1-16 1-17 Samsung Electronics...
Page 137
PLAY speed. Pully, Gear Idler rotate in order. Pinch Roller rotates 30 times Reel T rotates 30 times faster faster tnan PLAY speed. tnan PLAY speed. ✽ This operation feeds tape 30 times faster than PLAY speed. Samsung Electronics 1-18...
Page 138
BRAKE PULLY BRAKE S SWITCH MIC BRAKE MAIN T HOLDER FPC SUB MOTOR LOADING MOTOR CAPSTAN GEAR WHEEL GEAR MODE SWITCH GEAR CAPSTAN GUIDE TENSION CAM GEAR CAM MAIN SLIDE MAIN GEAR PULLY LEVER CAM Fig 1-17 1-19 Samsung Electronics...
Page 139
Timming, Gear pully and Gear ldler rotate in order. Reel totates 30 Reel S rotates 30 times faster than times faster than PLAY speed. PLAY speed. ✽ This operation feeds tape 30 times faster than PLAY mode. Samsung Electronics 1-20...
Page 140
SWITCH C-IN BRAKE PULLY BRAKE S SWITCH MIC BRAKE MAIN T HOLDER FPC SUB MOTOR LOADING MOTOR CAPSTAN GEAR WHEEL GEAR MODE SWITCH GEAR CAPSTAN GUIDE TENSION GEAR CAM MAIN SLIDE MAIN GEAR PULLY LEVER CAM Fig 1-18 1-21 Samsung Electronics...
Page 141
Reel T stops. Reel S stops. ✽ Drum is rotating during REC/PAUSE Push START/STOP Key. Motor Capstan rotates forward. Pinch Roller rotates. Reel S rotates. Reel T rotates. ✽ Tape is wound to Reel T by this operation. Samsung Electronics 1-22...
Page 142
BRAKE PULLY BRAKE S SWITCH MIC BRAKE MAIN T HOLDER FPC SUB MOTOR LOADING MOTOR CAPSTAN GEAR WHEEL GEAR MODE SWITCH GEAR CAPSTAN GUIDE TENSION CAM GEAR CAM MAIN SLIDE MAIN LEVER CAM GEAR PULLY Fig 1-19 1-23 Samsung Electronics...
Page 143
Lever Lock to release of Housing. ✽ S/W Push is turned off. Motor Capstan stops Motor Loading stops. Housing raised (Eject completed) Motor Loading rotates forward. Lever Eject moves back by Slider Main to lock Housing. Motor Loading stops. Samsung Electronics 1-24...
Page 144
REEL DISK T REEL DISK S GEAR IDLER BRAKE S BRAKE MAIN T MOTOR LOADING MOTOR CAPSTAN GEAR MODE SWITCH GEAR CAPSTAN SLIDE MAIN GEAR CAM MAIN GEAR PULLY LEVER CAM LEVER LOCK LEVER EJECT SWITCH C-In Fig 1-20 1-25 Samsung Electronics...
Page 145
Pully, Gear Idler rotate in order. Reel T rotates approx. 10.5 times faster Reel S rotates approx. 10.5 times faster than PLAY mode. than PLAY mode. ✽ Tape fed by Motor Capstan is wound up to Reel T. Samsung Electronics 1-26...
Page 146
1. 동작 영문 2001.7.4 2:4 PM 페이지1-27 Operation DRUM MOTOR CAPSTAN GEAR CAPSTAN BELT TIMMING REEL DISK T REEL DISK S GEAR IDLER GEAR CLUTCH Fig 1-21 1-27 Samsung Electronics...
Page 147
Idler rotate in oncler Reel T rotates in reverse Reel S rotates in reverse approx. 9.5 times faster approx. 9.5 times faster than PLAY mode. tnan PLAY mode. ✽ Tape fed by Motor Capstan is wound up to Reel S. Samsung Electronics 1-28...
Page 148
1. 동작 영문 2001.7.4 2:4 PM 페이지1-29 Operation DRUM MOTOR CAPSTAN GEAR CAPSTAN BELT TIMMING REEL DISK S REEL DISK T GEAR IDLER GEAR PULLY Fig 1-22 1-29 Samsung Electronics...
Page 149
1. 동작 영문 2001.7.4 2:4 PM 페이지1-30 MEMO Samsung Electronics 1-30...
Page 150
3. 분해및조립 영문 2001.7.4 2:10 PM 페이지3-1 3. Disassembly and Reassembly 3-1 How to Load and Unload (Setting the Mechanical Modes) 1. Set the power-supply output to approximately 5V, and connect it to the Motor Loading. 2. Choose the polarity depending on whether loading or unloading.(See Table 3-1) 3.
Page 151
3. 분해및조립 영문 2001.7.4 2:10 PM 페이지3-2 3-2 Housing 3-2-2 Reassembly 3-2-1 Disassembly 1. Mount the Cam L and Cam R of Lever NOTE : Do disassembled and reassembly in the unloading Housing ❹ to stud Housing L ❺ and stud Housing R❻.
Page 152
3. 분해및조립 영문 2001.7.4 2:10 PM 페이지3-3 3-3 Cover Reel Ass’ y, Idler Ass’ y 3-3-1 Disassembly 3-3-2 Reassembly 1. Remove the screw ❶, then lift the Cover 1. Fit the Idler Ass’ y ❹ into the Pin, then Reel Ass’ y ➋ in the direction of arrow. install the Washer Slit ❸...
Page 153
3. 분해및조립 영문 2001.7.4 2:10 PM 페이지3-4 3-4 Sub Chassis 3-4-1 Disassembly 3-4-2 Reassembly 1. Push the arm Tension Ass’ y ❹ in the Note 1 : when disassembling, take care not to direction of arrow A, insert Pin Lever Cam damage any parts.
Page 154
3. 분해및조립 영문 2001.7.4 2:10 PM 페이지3-5 3-5 Arm-Tension and Arm-Review 3-5-2 R e a s s e m b l y N o t e : When disassembling, take care not to 1. Insert the Arm Review ❺ into the pin1 ❽. deform the part.
Page 155
3. 분해및조립 영문 2001.7.4 2:10 PM 페이지3-6 3-6 Reel Disk S, T, Brake S, Brake Main T, Brake Pully, Lever Eject 3-6-1 Disassembly 3-6-2 R e a s s e m b l y 1. Separate the spring Brake S ❺ from the spring 1.
Page 156
3. 분해및조립 영문 2001.7.4 2:10 PM 페이지3-7 3-7 DRUM 3-7-2 R e a s s e m b l y 3-7-1 Disassembly 1. Mount and insert the Drum ❶ to the N o t e 1: Do not touch the Head tip❷ w h e n Bosses ❺.
Page 157
3. 분해및조립 영문 2001.7.4 2:11 PM 페이지3-8 3-8 Guide Rail Ass’ y 3-8-1 Disassembly 3-8-2 Reassembly 1. Insert the Spring Guide Roller 2 ❻ to the N o t e 1: When removing or reassembly, do not pole Base S ❽ and T ❾, and then assemble touch Guide Roller S ❹...
Page 158
3. 분해및조립 영문 2001.7.4 2:11 PM 페이지3-9 3-9 Motor Loading, Guide Tension Cam, Gear Wheel 3-9-1 Disassembly 3-9-2 Reassembly 1. Eliminate pt welding 4 part ❹. Reassemble in reverse order 2. Remove the screw 1 ❷ and the Hooke 2 ❼, and then Lift up the Loading ass’...
Page 159
3. 분해및조립 영문 2001.7.4 2:11 PM 페이지3-10 3-10 Motor Capstan, Holder FPC Sub, Arm Pinch Roller, Slide Main 3-10-1 D i s a s s e m b l y 3-10-2 Reassembly Reassembly in reverse order. Note 1 : When removing and reassembling, be careful not to giss the Gear Part.
Page 160
3. 분해및조립 영문 2001.7.4 2:11 PM 페이지3-11 3 - 11 Gear Cam Main, Lever Cam, Gear Connector 3 - 1 1-1 Disassembly 3 - 1 1-2 Reassembly 1. After lift the Gear Cam Main ❶, and then 1. Align the hole of the Gear Connector ❸ a n d lift up the Lever Cam ❷.
Page 161
3. 분해및조립 영문 2001.7.4 2:11 PM 페이지3-12 3-12 Gear Pully, Belt Timing, Gear Capstan 3-12-1 Disassembly 3-12-2 Reassembly 1. Rmove the washer slit ❶, Lift the Gear 1. Mount the Gear Pully ❹ and hang the Capstan ❷ Belt Timing ❸ on the Gear Pully ❹ 2.
Page 162
2. 조정 영문 2001.7.4 2:7 PM 페이지2-1 2. Adjustment 2-1 Operation Without Housing Assembly 1. Remove the Housing Ass’ y from the recorder unit. 4. Press the S/W Push(Keep ON status)to start 2. Connect the mechanical chassis to the recorder loading, and push the PLAY Key.(Cover the circuit to supply voltage.
Page 163
2. 조정 영문 2001.7.4 2:7 PM 페이지2-2 2-3 Maintenance Carry out the following periodic maintenance 2-3-2 Cleaning of Tape Path checks in order to fully exercise all functions, 1. In EJECT mode, clean the tape path operations and tape. system(from Pole Tension P1 through Pole After repairing, service the set as follows: Review P7, Pinch Roller and Capstan Shaft) and the Lower Drum.
Page 164
2. 조정 영문 2001.7.4 2:7 PM 페이지2-3 Adjustment 2-3-3 Periodic Maintenance and Check List When overhauling, refer to the following table. Table 2-2 Hours of use(H) Maintenance checks Remarks 500 1000 1500 2000 2500 3000 3500 4000 4500 5000 Cleaning of tape path ●...
Page 165
2. 조정 영문 2001.7.4 2:7 PM 페이지2-4 2-4 Mechanical Check and Adjustment 2-4-1 Tension Regulator Adjustment 2-4-1(C) REASSEMBLY 2-4-1(A) DISASSEMBLY 1. Refer to 3-2 to mount the Housing Ass’ y 1. Refer to 3-2 to remove the Housing Ass’ y 2-4-1(B) ADJUSTMENT 1.
Page 166
2. 조정 영문 2001.7.4 2:7 PM 페이지2-5 Adjustment 2-4-2 Back Tension Confirmation 2-4-4 Reel Table Height Check 1. Set up the cassette-torque tape. 2-4-4(a) REMOVA L 2. Set to CAMERA mode, push the 1. Refer to 3-2 : Remove the Housing Ass’ y. EDIT(+) KEY and check that the 2.
2-7 A) If not flat (B or C in Fig 2-7), do adjustments 2-5-2 through 2-5-5. Ⓒ Defect at outlet Fig 2-7 P 1 P 2 T Reel S Reel fig 2-8 Samsung Electronics...
Page 168
2. Set to REV mode and observe the outlet waveform of PB RF signal.(Fig 2-12) 3. If the outlet waveform is out-of-spec, turn P7 counterclockwise, and redo steps 1 and 2. Capstan Capstan Fig 2-9 Fig 2-10 Fig 2-11 Samsung Electronics...
Page 169
2-13) 2. Set to CUE mode. Confirm that the waveform peaks still have a uniform pitch. (Fig. 2-14 B) If the track pitch is not uniform, do section 2-5-2(Tracking Adjustment) Emin Emax Fig 2-12 Fig 2-14 Fig 2-13 Samsung Electronics...
Page 170
3 seconds. Also confirm that the tape is not twisted or curled around the Pinch R o l l e r . 4. Repeat steps 2. and 3. Capstan Fig 2-15 From the S-Reel To the T Reel Fig 2-16 Samsung Electronics...