Related Manuals for ROL ERGO Series EE - ECS+
Summary of Contents for ROL ERGO Series EE - ECS+
-
Page 1: User Manual
USER MANUAL Series EE - ECS+ Stroke 650/500/470 ROL | ERGO Sweden W: www.rolergo.com P: +46 36 36 88 80... -
Page 2: Declaration Of Conformity
DECLARATION OF CONFORMITY Manufacturer: ROL Ergo AB Flygplatsvägen 1 555 93 Jönköping SWEDEN www.rolergo.com Hereby assure that sit and stand desk, electrical adjustment ”EPI - The professional series” Type: EPI 1-COLUMN 2-STAGE (470) EPI 2-COLUMN 2-STAGE (470) EPI 2-COLUMN 3-STAGE (650) - Page 3 Please keep this manual for future reference. ROL Ergo AB is not liable for damage to people, animals or objects caused by improper or unauthorised use. This also applies for damage caused through disregard or insufficient consideration of the safety criteria contained in this user manual, or through alteration of the product or use of unsuitable spare parts.
-
Page 4: Table Of Contents
CONTENTS GENERAL INFORMATION ............5 Designated Use ........................5 Product Specifications ......................5 User Information ........................6 Before You Start ........................6 SAFETY INSTRUCTIONS ............7 ASSEMBLY & ADJUSTMENT ............ 9 Assembly Instruction ......................9 System Procedure ......................10 OPERATION INSTRUCTIONS ..........12 Basic Functions ........................12 Manual Reset ........................ -
Page 5: General Information
GENERAL INFORMATION Designated Use This stand is intended for use for electrical height adjustment of a sit-stand workstation commercially or in home environments. Any other uses are viewed as improper. The stand shall only be operated indoors in dry, enclosed environments. For maximum intended load and additional specifications see 1.2 Product Specifications. -
Page 6: User Information
User Information When customer support is required the operator may ask for information stated on the product label. The product label is located on the house of the motor on top of each column. Example of product label Example of power supply labels Before You Start Check for and remove obstacles in path of the desk top. -
Page 7: Safety Instructions
SAFETY INSTRUCTIONS DANGER • Improper usage, abuse, or misuse of the power supply, handset, motors and other electrical components may result in an electrical shock injury or possible death. • Do not open the power supply unit or handset under any circumstances. The power supply and handset contain no serviceable parts. - Page 8 • Never operate the desk with any openings blocked. • Never drop or insert any object into any opening. • Do not use outdoors. • To disconnect, turn all controls to the off position, then remove plug from outlet. • Do not exceed the maximum intended load.
-
Page 9: Assembly & Adjustment
ASSEMBLY & ADJUSTMENT Assembly Instruction The official assembly instruction can be found with the base components. Make sure to ask your desk vendor for an approved combination of desktop and frame. NOTICE Make sure that the desk is leveled, using the adjusters, and placed on flat ground before usage. -
Page 10: System Procedure
System Procedure WARNING The main power cord must be unplugged during the setup. To set up the desk: Connect the motor cables to the control unit 8-pin motor connections. Connect the handset to the relevant socket at the control unit/ECS+. Connect the power supply to the control unit/ECS+. - Page 11 DANGER Improper power connection of the equipment can result in a risk of electric shock. Check with a qualified electrician for any concerns. CAUTION When the power cord is plugged in, the electrical control devices are operational. NOTICE When disconnecting components such as the power supply, bus cable or the handset, the strain relieve hook must be pressed before removing the connector.
-
Page 12: Operation Instructions
OPERATION INSTRUCTIONS Basic Functions NOTICE Read the user manual carefully before installing or operating the control unit. If chosen handset is not covered this user manual, please see separate user manual supplied with the hand set. 4.1.1 Upward Desktop Movement This function enables the upward adjustment of the work surface. - Page 13 4.1.3 Limits If the software version in the handset is 4.20 or later it has an editable memory for high and low (stand and sit) position. It could also be used to avoid collision with i.e. a cabinet or pedestal. When a memory position is set the desk will stop when the memory position is reached.
-
Page 14: Manual Reset
Manual Reset If a motor or other electronic has been disconnected from the column, during or after the assembly, a reset (homing) cycle MUST be performed. A reset cycle should be made with an evenly distributed weight of approx. 45 kg (100 lbs) applied on the desk. Perform a reset by: Simultaneously pressing the up and down buttons for minimum of 8 seconds. -
Page 15: Maintenance & Repairs
MAINTENANCE & REPAIRS Cleaning, Inspection & Storage Clean the desk stand by wiping it down with a dry microfiber cloth. Never use solvent, abrasive or corrosive compounds. Products must be cleaned at regular intervals to remove dust and dirt and inspected for mechanical damage and normal wear and tear. -
Page 16: Servicing Of Double-Insulated Products
The control system is equipped with safety features; the intermittency function, the overheating protection and memory function: • Duty cycle function – The duty cycle factor of the desk 1:9 meaning 1 minute of operation must be followed by 9 minutes of inactivity. If this limitation is exceeded, the desk will become inoperable until the control box resets automatically. -
Page 17: Appendix
APPENDIX Dimensions leg system: Series EE - ECS+ with 500 & 650 stroke ROL | ERGO Sweden W: www.rolergo.com P: +46 36 36 88 80... -
Page 18: Dimensions Leg System: Series Ee - Ecs+ With 470 Stroke
Dimensions leg system: Series EE - ECS+ with 470 stroke ROL | ERGO Sweden W: www.rolergo.com P: +46 36 36 88 80... -
Page 19: Troubleshooting
Troubleshooting Desk able to move Only one column moving Do a reset Only one column moving Two columns moving Change the column at different speeds that is moving Change the column that is moving faster than the other Desk moving too slow Only able to drive down Do a reset Change power supply... -
Page 20: Rol | Ergo Sweden W: Www.rolergo.com P: +46 36 36 88
The green light on the Change power supply power supply goes out Desk overloaded Unload the desk Change ECS box Desk stops and reverse during operation Something is blocking Remove the obstacle the table movement Mechanical damage Change the columns on column Not able to drive all the way Do a reset... - Page 21 Unplug the desk from the wall socket for roughly one minute and reconnect Desk stuck in absolute Do a reset top or bottom position All cables are connected The green light on the power supply is lit Change ECS box Change the power supply Follow install instructions ROL | ERGO Sweden...
Need help?
Do you have a question about the Series EE - ECS+ and is the answer not in the manual?
Questions and answers