Advertisement
Quick Links
JET-VAC
AUTOMATIC
POOL CLEANER
I N S T A L L A T I O N G U I D E
A N D
O W N E R S M A N U A L
M A D E I N A U S T R A L I A B Y
Automatic Pool Cleaners (Australia) Pty Ltd
40 Percy Street, Auburn NSW 2144 Australia
Ph: +61 2 9643 8338 Fax: +61 2 9643 8448
www.aquaquip.com.au
www.jetvac.com.au
1
J E T - V A C
A U T O M A T I C
P O O L
C L E A N E R
–
I N S T A L L A T I O N
&
O P E R A T I N G
I N S T R U C T I O N S
Advertisement
Related Manuals for Aqua Quip Jet-Vac
Summary of Contents for Aqua Quip Jet-Vac
- Page 1 JET-VAC AUTOMATIC POOL CLEANER I N S T A L L A T I O N G U I D E A N D O W N E R S M A N U A L M A D E I N A U S T R A L I A B Y...
- Page 2 CONGRATULATIONS on purchasing Jet-Vac, the finest pool cleaner available today. Jet-Vac has a patented, built-in backup system that will move the unit out of corners and away from other obstacles that tend to trap other pool cleaners. The unit moves forward for approximately three minutes, then backs up and turns for approximately 45 seconds, all the while vacuuming and sweeping your pool in a random pattern.
-
Page 3: Installation Procedure
Please note, a Booster Pump is required for the 40mm (1½”) female threads. The Jet-Vac wall fitting Jet-Vac to work. If you do not have an existing screws into this 40mm (1½”) female thread. If the booster pump please contact your local pool pool has 19mm (¾”) female threads, it will require the... - Page 4 SECOND SECTION is a DARK BLUE HOSE that fits between the WHITE HOSE and the LIGHT 3) Take the “sweep hose” end of the Jet-Vac hose BLUE HOSE. and walk around the circumference of the pool to find the point that is furthest from the wall fitting.
- Page 5 Once installed, prematurely wear the material in the JV32 Fine Debris the feed hose may try to coil up, causing the Jet-Vac Bag. Therefore, it may be more suitable to use to climb and fly around the pool.
-
Page 6: Troubleshooting
172-193 kpa (25-28 psi). See Diagram 3. Diagram 3 GENERAL TROUBLESHOOTING Over time, if your Jet-Vac’s performance diminishes please check the Regular Maintenance Checklist below. JET-VAC REGULAR MAINTENANCE CHECK LIST: • Check and clean the wall fitting strainer regularly. - Page 7 Each pool is different, and sometimes Jet-Vac does temporarily get snagged in sharp corners or steps. As long as Jet-Vac is able to reverse out of these obstructions, it will keep your pool clean. Adjust the angle of the JV12 Roller Arm up or down (by...
- Page 8 High pressure filtered water is pushed from the Booster Pump through the supply line, through the wall fitting and strainer, through the feed hose to the Jet-Vac. Some of the water is directed to the sweep hose before entering the Jet-Vac head. Water enters the Jet-Vac head and half is directed to the upward facing venturi jet, shooting water up into the bag and drawing in dirt and leaves.
- Page 9 (part # JV12) to the Jet-Vac the Jet-Vac will help it climb up into the shallow end body. Place the Jet-Vac on a flat surface and of the pool.
- Page 10 JV42 JV43 SCREW JV43S SCREW Note: See Page 9 for Jet-Vac Hose Diagram and Parts List. JV44 SCREW (PUSHER JET) J E T - V A C A U T O M A T I C P O O L C L E A N E R –...
- Page 11 JET-VAC AUTOMATIC POOL CLEANER Note: See Page 9 for Jet-Vac Hose Diagram and Parts List. J E T - V A C A U T O M A T I C P O O L C L E A N E R –...
- Page 12 AUTOMATIC POOL CLEANER JET-VAC WARRANTY For full warranty conditions please refer to the Warranty Card enclosed with your new Jet-Vac which details the warranty registration procedure. For your future reference, please record proof of purchase details here: Serial Number: S/N can be found in three places: on underside of the bottom plate of head unit;...
Need help?
Do you have a question about the Jet-Vac and is the answer not in the manual?
Questions and answers