Table of Contents
Advertisement
JET-VAC
AUTOMATIC
POOL CLEANER
I N S T A L L A T I O N G U I D E
A N D
O W N E R S M A N U A L
M A D E I N A U S T R A L I A B Y
Automatic Pool Cleaners (Australia) Pty Ltd
40 Percy Street, Auburn NSW 2144 Australia
Ph: +61 2 9643 8338 Fax: +61 2 9643 8448
www.aquaquip.com.au
www.jetvac.com.au
1
J E T - V A C A U T O M A T I C P O O L C L E A N E R – I N S T A L L A T I O N & O P E R A T I N G I N S T R U C T I O N S
Advertisement
Table of Contents
Related Manuals for Aqua Quip JET-VAC
Summary of Contents for Aqua Quip JET-VAC
- Page 1 JET-VAC AUTOMATIC POOL CLEANER I N S T A L L A T I O N G U I D E A N D O W N E R S M A N U A L M A D E I N A U S T R A L I A B Y...
- Page 2 CONGRATULATIONS on purchasing Jet-Vac, the finest pool cleaner available today. Jet-Vac has a patented, built-in backup system that will move the unit out of corners and away from other obstacles that tend to trap other pool cleaners. The unit moves forward for approximately three minutes, then backs up and turns for approximately 45 seconds, all the while vacuuming and sweeping your pool in a random pattern.
-
Page 3: Installation Procedure
Pump box. MENDER NUTS: Please note, a Booster Pump is required for the Jet-Vac to work. If you do not have an existing These plastic nuts provide a gripping hold over hose booster pump, you should have purchased a ends that have been pushed down over various fittings Jet-Vac unit complete with pump. -
Page 4: Feeder Hose Assembly
SECOND SECTION is a DARK BLUE HOSE that fits between the WHITE HOSE and the LIGHT 3) Take the “sweep hose” end of the Jet-Vac hose BLUE HOSE. and walk around the circumference of the pool to find the point that is furthest from the wall fitting. -
Page 5: Assemble And Install Jet-Vac Head Unit
ASSEMBLE AND INSTALL JET‑VAC warranty. Excess pressure can also cause the HEAD UNIT: Jet-Vac to “fly” off the bottom of the pool surface. 1) Attach JV30 Funnel Adaptor to Jet-Vac head. The Jet-Vac installer will need the JVP8 Pressure Test Ensure JV29 Gasket is sitting flat in JV30. - Page 6 Once installed, of the hose should enable the Jet-Vac to travel more the feed hose may try to coil up, causing the Jet-Vac consistently on the pool floor and track steadier.
-
Page 7: Troubleshooting
(part # JV12) to the Jet-Vac the Jet-Vac will help it climb up into the shallow end body. Place the Jet-Vac on a flat surface and of the pool. - Page 8 High pressure filtered water is pushed from the Booster Pump through the supply line, through the wall fitting and strainer, through the feed hose to the Jet-Vac. Some of the water is directed to the sweep hose before entering the Jet-Vac head. Water enters the Jet-Vac head and half is directed to the upward facing venturi jet, shooting water up into the bag and drawing in dirt and leaves.
- Page 9 • Make sure that any worn parts on the Jet-Vac are promptly replaced. • When the Jet-Vac is not in use, ensure that it is not stored in a coiled-up position. Regular checking and maintenance of your Jet-Vac will help prevent premature wear and tear.
- Page 10 JET-VAC AUTOMATIC POOL CLEANER JET-VAC PARTS LIST Venturi Shell JV53 Hose Sleeve JV2B Deflector Plate Assembly JV54 Roller Ring Adaptor JV55 Hose Jet Collar JVF7 O-Ring for JV3 JV56 Hose Jet Shell Float JV61 Lock Washer JV4B Float Cover Button Kit...
- Page 11 JET-VAC AUTOMATIC POOL CLEANER J E T - V A C A U T O M A T I C P O O L C L E A N E R – I N S T A L L A T I O N & O P E R A T I N G I N S T R U C T I O N S...
- Page 12 3) It shall be the purchaser’s responsibility to provide Automatic Pool Cleaners (Australia) Pty. Ltd safe and reasonable access to the equipment (Aqua-Quip) warrants Jet-Vac to be free from original before warranty service will be performed. manufacturing defects and faulty materials under...
Need help?
Do you have a question about the JET-VAC and is the answer not in the manual?
Questions and answers