Page 11
Feb. 2010 SECTION 10 SECTION 10. VOLTAGE DIAGRAM • LOGIC UNIT (Left side) CPU-MAIN DIAL MMZ1005Y102CT IMSA-9631S-27Y921 MMZ1005Y102CT TP70N00E2015F LCDCS LCDRES LCDRS LCDCK LCDDT MENU LEFT LCD Back Light DOW NR I GHT BACK LIGHT ON :2.2V LIGHT LIGHT OFF:0.0V 2SC4617 SCAN R228...
Page 12
Feb. 2010 • LOGIC UNIT (Right side) CPU-MAIN COM:12.7V VP_DC-DC BAR ANT AF_TRUTH PSTB2 PSTB1 AGCC PDATA KY-058 VCO4 R SSI VCO3 XP4601 IC11 TRUTH NOISE VCO2 C127 C131 C137 C142 C149 SHIFT VCO1 IC16 DASTB ATTC LDATA FSET ANTSW 3076 TC7W04FU SHIFT3V...
Page 13
Feb. 2010 • MAIN UNIT (Left side) EARPHONE ANT ON :3.1V EARPHONE ANT OFF:0.0V 1SV308 R233 1.5K UNR9115G0 RF_IN 100K 500kHz:0.4V BAR_ANT(0.45-1.62MHz ) C102 C118 2SC5006 1SV308 1SV308 0.01 0.15U 0.15U XP4312 ATT ON :3.1V 2SC4738 ATT OFF:0.0V C104 2.7K SW(0.15-0.45 / 1.62-76MHz) 0.10U 1SV308...
Page 14
Feb. 2010 • MAIN UNIT (Right side) Reference Frequency check point; CP6 2nd IF FILTER 1 st IF FI LTER C435 AM/NFM_CONT IF AMP RX:0.9V 0.01 0.001 Reference frequency signal AMP UPC2757TB EFCH429MKQP1 UPC2757TB DAN235E 2SC5006 C203 R167 C158 C173 C190 C405 C223...
Page 25
Feb. 2009 SECTION 10 SECTION 10. VOLTAGE DIAGRAM • LOGIC UNIT (Left side) CPU-MAIN DIAL MMZ1005Y102CT IMSA-9631S-27Y921 MMZ1005Y102CT TP70N00E2015F LCDCS LCDRES LCDRS LCDCK LCDDT MENU LEFT LCD Back Light DOW NR I GHT BACK LIGHT ON :2.2V LIGHT LIGHT OFF:0.0V 2SC4617 SCAN R228...
Page 26
Feb. 2009 • LOGIC UNIT (Right side) CPU-MAIN COM:12.7V VP_DC-DC BAR ANT AF_TRUTH PSTB2 PSTB1 AGCC PDATA KY-058 VCO4 R SSI VCO3 XP4601 IC11 TRUTH NOISE VCO2 C127 C131 C137 C142 C149 SHIFT VCO1 IC16 DASTB ATTC LDATA FSET ANTSW 3076 TC7W04FU SHIFT3V...
Page 27
Feb. 2009 • MAIN UNIT (Left side) EARPHONE ANT ON :3.1V EARPHONE ANT OFF:0.0V 1SV308 R233 1.5K UNR9115J RF_IN 100K 500kHz:0.4V BAR_ANT(0.45-1.62MHz ) C102 C118 2SC5006 1SV308 1SV308 0.01 0.15U 0.15U XP4312 ATT ON :3.1V 2SC4738 ATT OFF:0.0V C104 2.7K SW(0.15-0.45 / 1.62-76MHz) 0.10U 1SV308...
Page 28
Feb. 2009 • MAIN UNIT (Right side) Reference Frequency check point; CP6 2nd IF FILTER 1 st IF FI LTER AM/NFM_CONT C435 IF AMP RX:0.9V 0.01 0.001 Reference frequency signal AMP UPC2757TB UPC2757TB EFCH429MKQP1 DAN235E 2SC5006 C203 R167 C158 C173 C190 C405 C223...
Page 30
WIDEBAND RECEIVER S-14510XZ-C1 Aug. 2008...
Page 31
Addresses are provided on the inside back cover for your convenience. Icom, Icom Inc. and logo are registered trademarks of Icom Incorporated (Japan) in the United States, the United Kingdom, Germany, France, Spain, Russia and/or other countries.
SECTION 1. SPECIFICATIONS D General D Receiver • Frequency coverage • Receive system : Triple-conversion superheterodyne (Unit: MHz) 0.150–821.995, 851.000–866.995, • Intermediate frequencies : 1st : 429.1 MHz, 896.000–1300.000 2nd : 19.65 MHz (FM/AM), Other than USA 0.150–1300.000 20.75 MHz (WFM) •...
Page 34
SECTION 2. INSIDE VIEWS • LOGIC UNIT EEPROM (IC14) EEPROM (IC15) 3V line SW (IC17) (Q28) CLONE BUFFER (IC8) 3V REG TONE CONTROLER (AF SW) (IC4) (IC20) 3.2V REGULATOR (IC3) TONE FILTER (IC12) • MAIN UNIT 2ND VCO 1ST VCO REFERENCE FREQUENCY OSCILLATOR (X1)
Page 35
SECTION 3. DISASSEMBLY INSTRUCTION 1. Removing the front panel 2. Removing the LOGIC UNIT q Unscrew 4 screws from the rear panel. q Unscrew total of 4 screws from the LOGIC UNIT. w Unsolder 3 points at the rotary encoder (CONTROL 4 screws DIAL), then remove the LOGIC UNIT from the rear panel.
SECTION 4. CIRCUIT DESCRIPTION 4-1 MAIN UNIT RF AMP/FILTER CIRCUITS (1 GHz BAND) MAIN UNIT has RF circuits, 1st and 2nd IF circuits, FM and AM demodulator circuits. The RX signals from the antenna The 833–1300 MHz RX signals are passed through the diode SW (D10) and HPF/LPF for unwanted signal removal, are fi...
to the RF AMP and IF AMP for AGC operation. The 4-3 2nd VCO UNIT demodulated AF signals are entered to the LOGIC UNIT via The 2nd VCO UNIT oscillates the 2nd LO signals. The VCO AF SW (IC9). oscillates 409.4500/448.7500 MHz signal in FM/AM mode, and oscillates 408.3500/449.8500 MHz signal in WFM mode .
Page 38
4-4 LOGIC UNIT The LOGIC UNIT has CPU, D/A converter (DAC), AF circuits AF CIRCUITS and power supply circuits. The CPU and DAC control the Other than WFM mode operation, and when the AF fi lter is whole operation of the receiver (RX frequency setting, BPF activated, the demodulated AF signals are passed through tuning etc.), and the AF circuits filter, amplify and tone- the AF fi...
4-5 VOLTAGE DIAGRAM Voltage from the power supply is routed to the whole of the receiver via the regulators and switches. LOGIC UNIT MAIN UNIT [DC 6V] I C11:TC7W04FU Q24:2SC4738 IC3:NJU7775F3 Q2:2SA1588 D24-D27:1SS372 +10V CPU3V CHARGE CPU3V Padding voltage to the loop filter (1stV), Tuned BPFs (M: D53, 58) DC-DC CONTROL BATTERY...
4-6 CPU PORT ALLOCATION LINE LINE DESCRIPTION DESCRIPTION NAME NAME CTONE Demodulated tone signals. Key matrix. Filtered demodulated signal (extracted +3V line SW VSCAF PCON voice signal). "L"=Power ON Charge status. Tone fi lter (L: IC12) SW TCON "H"=While pre/fast charging. "L"=Filter activated.
SECTION 5. ADJUSTMENT PROCEDURE 5-1 PREPARATION ¤ REQUIRED TEST EQUIPMENTS EQUIPMENT GRADE AND RANGE EQUIPMENT GRADE AND RANGE Frequency range : 0.1–1500 MHz Frequency range : 0.1–30 MHz Standard Signal Output level : 0.1 µV to 32 mV Frequency Counter Frequency accuracy : ±1 ppm or better Generator (SSG) (–127 to –17 dBm)
5-2 ADJUSTMENTS ADJUSTMENT DISPLAYED ITEM OPERATION VALUE REFERENCE 1) Remove the front panel and LOGIC UNIT to expose FREQUENCY the MAIN UNIT. (Refer to the DISASSEMBLY INSTRUCTION) 19.2000 MHz [REF] 2) Connect a Frequency Counter to the CP6 on the ±3 ppm MAIN UNIT through a thin coaxial cable as below.
Page 43
ADJUSTMENT DISPLAYED ITEM OPERATION VALUE SENSITIVITY • Connect an SSG to the antenna connector, and set it as; -MF band- Frequency : (Displayed on the function display) (Preparation) – Modulation : 1 kHz Deviation : 3.5 kHz (FM) Level : –5 dBµ (Band high) 1) Set the SSG as;...
Page 44
ADJUSTMENT DISPLAYED ITEM OPERATION VALUE S-METER CURVE • Connect an SSG to the antenna connector and set it -145 MHz- – – (Preparation) Modulation : 1 kHz Deviation : 3.5 kHz (FM) (S0 level) 1) Set the SSG as; Frequency : (Displayed on the function display) [S0] Level : –9 dBµ...
Page 45
ADJUSTMENT DISPLAYED ITEM OPERATION VALUE • Connect an SSG to the antenna connector and set it S-METER – – (Preparation) Modulation : 1 kHz -MF band- 1) Set the SSG as; (FM:S3 level) Frequency : (Displayed on the function display) [FS3] Deviation : 3.5 kHz (FM)
Page 46
ADJUSTMENT DISPLAYED ITEM OPERATION VALUE 1) Set the SSG as; -200 MHz band- (FM:S3 level) Frequency : (Displayed on the function display) [FS3] Deviation : 3.5 kHz (FM) Level : –5 dBµ 2) Push [ENT MW] key. 1) Set the SSG as; -200 MHz band- (WFM:S0 level) Frequency : (Displayed on the function display)
SECTION 10. VOLTAGE DIAGRAM • LOGIC UNIT (Left side) CPU-MAIN DIAL MMZ1005Y102CT IMSA-9631S-27Y921 MMZ1005Y102CT TP70N00E2015F LCDCS LCDRES LCDRS LCDCK LCDDT MENU LEFT LCD Back Light DOW NR I GHT BACK LIGHT ON :2.2V LIGHT LIGHT OFF:0.0V 2SC4617 SCAN R228 TXD2 RXD2 SCK2 SERCH...
• MAIN UNIT (Right side) Reference Frequency check point; CP6 2nd IF FILTER 1 st IF FI LTER AM/NFM_CONT C435 IF AMP RX:0.9V 0.01 0.001 Reference frequency signal AMP UPC2757TB EFCH429MKQP1 UPC2757TB DAN235E 2SC5006 C203 C158 C173 C190 C405 C223 R167 C269 C284...
Need help?
Do you have a question about the IC-RX7 and is the answer not in the manual?
Questions and answers