"LD Degration Judgment of ATA/ATAPI DEBUG OSD" and "LD POWER ADJUSTMENT"*. 2. When the cover is opened, close viewing of the objective lens with the naked eye will cause exposure to a Class 3A laser beam. * Refer to Pages 54 and 89. DVR-LX61D...
Page 3
To protect products from damages or failures during transit, the shipping mode should be set or the shipping screws should be installed before shipment. Please be sure to follow this method especially if it is specified in this manual. DVR-LX61D...
1.1 NOTES ON SOLDERING ...............................6 1.2 NOTES ON HANDLING THE HDD..........................7 1.3 NOTES ON REPLACEMENT OF THE SDRAM ......................9 1.4 NOTES ON REPLACEMENT OF THE FL LENS (DVR-LX61D ONLY).................10 1.5 NOTE ON PC CARDS ..............................10 2. SPECIFICATIONS ................................11 2.1 ACCESSORIES ................................11 2.2 SPECIFICATIONS.................................12...
Page 5
10.8 SERVICE MAIN ASSY (3/5) ............................. 132 10.9 SERVICE MAIN ASSY (4/5) ............................. 134 10.10 SERVICE MAIN ASSY (5/5) ........................... 136 10.11 ETAB ASSY (DVR-LX61D ONLY) ........................... 138 10.12 SERVICE DVUB ASSY............................140 10.13 SERVICE DTBR ASSY (1/3) ..........................142 10.14 SERVICE DTBR ASSY (2/3) ..........................
Compared with eutectic solders, lead-free solders have higher bond strengths but slower wetting times and higher melting temperatures (hard to melt/easy to harden). The following lead-free solders are available as service parts: • Parts numbers of lead-free solder: GYP1006 1.0 in dia. GYP1007 0.6 in dia. GYP1008 0.3 in dia. DVR-LX61D...
• When packing, use the antistatic bag and packing materials in which the repair part for service was delivered. Attach a copy of the slip for service or a memo stating symptoms in as much detail as possible. DVR-LX61D...
[3] Outline and part No. of the HDDs *Pioneer's part No. is not stamped. SEAGATE Model Pioneer's Capacity Manufacture's Name Part No. Part No. (for service) DVR-LX61D 250GB VXF1131 ST3250820SCE DVR-560HX-S 160GB VXF1152 ST3160215SCE DVR-560HX-K • When replacing the HDD, carefully check the capacity and manufacturer's part No. on the part label to avoid replacing with a similar but inappropriate product.
Replacement of only the defective SDRAM (IC1201 or IC1221) is possible. Possible malfunctions If SDRAMs made by different manufacturers are mounted on the MAIN Assy, the following malfunctions may occur: 1. The power does not come on. 2. High-speed dubbing disabled 3. Other malfunctions related to the SDRAM DVR-LX61D...
1.4 NOTES ON REPLACEMENT OF THE FL LENS (DVR-LX61D ONLY) The Panel Frame, FL Lens, and FL Filter are attached to the chassis with two-sided (double-back) tape. If one of these parts has to be replaced, replace all three parts at the same time.
Before shipping out the product, be sure to clean the following positions by using the prescribed cleaning tools: Position to be cleaned Cleaning tools Pickup lenses Cleaning liquid : GEM1004 Cleaning paper : GED-008 Position to be cleaned Cleaning tools Fans Cleaning paper : GED-008 DVR-LX61D...
Page 32
HDD contents 1. Model setting 2. LD power adjustment MAIN ASSY 3. CPRM setting 4. Firmware update 1. Model setting TUSB ASSY 2. CPRM setting 3. Firmware update LOADER ASSY 1. LD power adjustment 1. CPRM setting 2.Gracenote Database update DVR-LX61D...
3.3e-3 or below (maxell DRM120C.1P5S) GGV1036 : DVD-ROM DL L0/L1 : 8.0e-4 or below (DVDT-002) How to read error rate X.Xe-Y Y: The bigger the better, X X: The smaller the better How to exit from Service Mode [ESC] DVR-LX61D...
Therefore, when replacing, be sure to use parts of identical designation. Mark No. Description Part No. Mark No. Description Part No. LIST OF ASSEMBLIES • For DVR-LX61D model • For DVR-560HX model 1..ETAB ASSY VWV2344 1..TUJB ASSY YWM1001 2..SERVICE DVUB ASSY YXX1001 1..TUJB ASSY...
VDA1681 Serial Update (*) Be sure to use the latest disc (Type 2). In Apr, 2008, the latest disc is GGV1321. [2] Lubricants and Glues List Name Lubricants and Glues No. Remarks Hanarl GEM1041 refer to "FRONT PANEL SECTION" DVR-LX61D...
72 71 90 89 AVLTH AVLTH Voltage Voltage change change IC406 IC406 SERVICE SERVICE TC7S66FU MUTE MUTE TC7S66FU MUTE MUTE TUSB TUSB ASSY ASSY JA501 (1/2) JA501 (2/2) JA501 (2/2) JA501 (1/2) to TV from STB to TV from STB DVR-LX61D...
Page 39
512M DDR SDRAM 512M DDR SDRAM 64M Flash 512M DDR SDRAM 512M DDR SDRAM 64M Flash EDD5116AFTA-6B-E EDD5116AFTA-6B-E S29GL 128N90T EDD5116AFTA-6B-E SERVICE MAIN ASSY EDD5116AFTA-6B-E S29GL 128N90T SERVICE MAIN ASSY FIR2 FIR2 CN201 CN201 For Debac For Debac RVICE RVICE DVR-LX61D...
1.0V for DEC IC3707 1.0V for PLL IC4541 V+3A 3.3V for AVDD33 VREF16 VRPD SW+12V(W) IC4501 V+12M VREFPD FTS Driver V+5M IC501 VD3V IC4502 SW+5V(W) VO5V VA5V CN203 P.U. SW+12V(H) SW+5V(H) SERVICE MAIN ASSY S P D L H D D DVR-LX61D...
"E01 or E02" displayed on FL display ∗1: If both the drive ID check and starting/ID Is disc in? check of HDD failed, "CPRM ERR" is first displayed on FL display. Is disc valid? Tray Open Repair required? Repair process Playback requested? Playback Stop DVR-LX61D...
(Failure in the periphery of AUDIO DAC for output audio.) DVD recording Failure in the periphery of CN101 Can record desired video and audio? (Poor contact with the Pickup Assy.) Failure in the periphery of IC1001 (There is possibility of failure of the EMMA2RFE chip.) DVR-LX61D...
Page 43
It is most likely that IC5801 and the Possible defect in EMMA2RFEX. subsequent parts are in failure. Check the soldering of the parts listed below: • IC5801 itself • L5801 to L5804, JA5801 • R5842 to R5845, C5815 to 5818 DVR-LX61D...
Page 44
Are some spots missing by dots (missing pixels) on the screen? If so, there may be problems in the length or quality of the cable or the reception capacity of the monitor. Check if the symptom disappears when a 5-meter or less cable made by JAE is used. DVR-LX61D...
Page 45
• R5865 (HTX_CLK) Note 1 : R5708: AT model From the following points, a 3.3V R5701: DT model swing signal must be output: • R5826 to R5828 There may be a problem with the EMMA2RFEX. DVR-LX61D...
IC106 and its periphery are likely to be defective. • Except when the local regulator is in failure, a power failure (blown a fuse, etc.) makes other input systems abnormal. • If mosaic images are often displayed, check the items in [B]. DVR-LX61D...
Press the ESC key. [How to quit] [Description] (1) First screen OK : Appropriate version compared with that of the firmware of DVR-LX61D/WY VERSION : 0.14 the system control computer. SYSCON : RELEASE_179 NG- : The version of the TUNER microcomputer is older.
Page 49
[How to enter] While the User Setting display is displayed, press the ESC , DISP , then DIG/ANA keys, in that order. [How to quit] Press the ESC key. [Description] DVR-LX61D/WY VERSION : 0.14 SYSCON : RELEASE_179 Rev.1.7379 TUNERCON : 2.22...
Page 50
During VR mode playback, the average value of the past 10 VOBUs is displayed. During DVD-Video or Video mode playback, the average value of the past 256 sectors is displayed. During VR mode playback, the speed ratio of the drive (/: normal, no indication: double speed) is also displayed. DVR-LX61D...
Page 51
(to display the CPRM setting screen, press the ESC then the STEREO keys). Notes: • The data on cumulative HDD-on time are not cleared when resetting to factory-preset values is performed. • The data on cumulative HDD-on time are not cleared when the system-control computer software is downloaded. DVR-LX61D...
Page 52
[ x 3 Fwd ], [SPEED-] [ x 3 Fwd], [SPEED-] : The setting value decreases by 1. [CLEAR] The setting value is reset to default. – To exit the OSD Filter Setting and [ESC] clear the screen (Appears the tuner – – screen.) DVR-LX61D...
MAIN Assy is replaced, the data will be cleared. However, after the LOADER Assy is replaced, data on lighting time of each LD will be retained in the MAIN Assy. Therefore, before either the MAIN Assy or LOADER Assy is to be replaced, it is recommended that you write down the lighting time data. DVR-LX61D...
Page 54
4-digit hexadecimal) Writer adjustment data for straight (non-HDD) model No condition (FFFF is diplayed when the writer is not adjusted.) If the results of degradation of the LDs for CDs or DVDs are NG, replace the drive. DVR-LX61D...
• The two error-log screens can be switched by pressing the SPEED+ or SPEED- key. [Tips] • For details on error messages, see Table 1 "Description of VR-recording-related errors". (4) Subscreen 5 to 12 (These subscreens are not for service use.) DVR-LX61D...
Page 56
VC HDD C Err No information on Video Mode Copy HDD VC HDD Inf NG Format failed VC HDD Info NG VC Idling NG Video Mode Copy idling NG VC Pck Anl NG Analizing Video Mode Copy Pack failed DVR-LX61D...
Page 57
Abnormal temperatute PARAM NO ACCP Recording parameter is not matched. Process Over Process is overfull. Protect Src * Source to be recorded is copy-protected. Rec Pause * No operation permitted during recording pause Relocation Do VR-recording data was relocated DVR-LX61D...
Page 58
File development of Gracenote Database failed. HDD TFD WR NG File deletion of Gracenote Database failed. HDD TFD CL NG Gracenote Database not downloaded HDD TFD NON Problem in Gracenote Database HDD CDDB NG File operation of Gracenote Database failed. GN API NG DVR-LX61D...
Page 59
RMA = Recording Management Area PCA = Power Calibration Area MKB = Media Key Block OPC = Optimum Power Control TMP_VMGI = Temporary Video Manager Information NWA = Next Writable Address Border = from Lead-in to Lead-out RSAT = Reserved Space Allocation Table DVR-LX61D...
* If information on errors which occurred on days earlier than the current day is contained on the screen, the information that follows the information which are displayed with "^" between “Time of occurrence”, “Name”, “Line” and “Message” indicates the errors that occurred on the current day. DVR-LX61D...
GUID : Global Unique ID (Specific ID for DV devices) GUID set in ConfigROM of the unit GUID If the unit is ROOT (IRM), IRM is displayed at the side position of GUID display. DVR-LX61D...
Page 64
1250-50, or Invalid) is indicated, Without input: "No" is indicated. If SF is 44 kHz, it is considered that 44.1-kHz audio is Sampling Frequency of DVdecode Stream input, and sound is muted on the unit. QUANTIZATION of DVdecode Stream AUDIO MODE of DVdecode Stream AMODE DVR-LX61D...
A number 999,999 or greater is displayed as "999999." [Tips] In a case where only "HS" is displayed in the MD column of the logs, the host channel has not been found. It is necessary to check the country and postal-code settings in the user settings. DVR-LX61D...
Page 67
: Slice level control Auto-Tu Con, Manual - Syscon. : Equalizer setting (ON, OFF) : Slice level (10~30 hex) (Only when the slice Count is Manual.) Note: The data on lines 12-14 are for software development, not for service use. DVR-LX61D...
480p NTSC 720x480p NTSC 720p NTSC 1280x720p NTSC 1080i NTSC 1920x1080i NTSC 1080p NTSC 1920x1080p NTSC 576i PAL 720x576i PAL 576p PAL 720x576p PAL 720p PAL 1280x720p PAL 1080i PAL 1920x1080i PAL 1080p PAL 1920x1080p PAL ---------- TMDS Off DVR-LX61D...
Page 69
Refer to this item only when HDMI or DVI is displayed for the item for the type of the connected device (Table 5). When there is also no valid SRM (include Revocation list), "--" is displayed here. Table 9: Fs Indication Description 32kHz 44.1kHz 48kHz 96kHz 48kHz (original data of 96kHz is down-sampled.) 96k/2 Audio Off DVR-LX61D...
OSD. Note: Recording time depends on the recording rate set. For example, if the recording rate is MN32, only up to 60 titles can be registered. Check the setting for recording rate before performing aging. DVR-LX61D...
Page 71
During Aging, the number of loops is indicated on the FL display, as shown below. [Tips] [AGING 0001] If an error is generated, the aging operation stops. Note: Indications on the FL display are retained, and this information is also retained as an OSD. DVR-LX61D...
Possibility of breakage of the internal flexible cables that connect USB connector A (at the front defective. panel) and B (at the front panel) with the control circuitry on the MAIN Assy. EMMA2RFEX on the MAIN Assy is in failure. DVR-LX61D...
Execute Extended Self-Test. Result of the diagnosis: Failure in HDD Measures to be taken: Replacement of HDD Has an error occurred? Execute writing test, if required. Execute HDD Read/Write Check. Has an error occurred? Result of the diagnosis: No abnormality DVR-LX61D...
Page 74
The status of the unit recommended during diagnosis is as follows: All stop, no timer recording (including auto-recording), and Input selection to L1-L3. DVR-LX61D...
Page 75
The HDD has come to the end or near the end of its service life. not exceeded: The HDD has not reached the end of its service life. To return to the menu screen, press the "Clear" key. DVR-LX61D...
Page 76
If it is from 3 to 7, the HDD must be replaced. Note: If the result of the second test is the same, replacement of the HDD is required. Example: No error Example: With an error To return to the menu screen, press the "Clear" key. DVR-LX61D...
Page 77
If it is from 3 to 7, the HDD must be replaced. Note: If the result of the second test is the same, replacement of the HDD is required. Example: No error Example: With an error To return to the menu screen, press the "Clear" key. DVR-LX61D...
Page 78
When the status is OFF To terminate the diagnostic program, press the "ESC" key. When the status is ON The status becomes OFF when the test is interrupted by pressing the "SKIP o" key or when "Progress" reaches 100%. DVR-LX61D...
(3) In response to the process in step (2) above, a low signal is output from Pin AAC_INT_B. (4) Steps (2) and (3) are repeated until the startup process is completed. Second screen: Information on playback of MUSIC files (Note 2) DVR-LX61D...
Page 80
The first 4 digits denote date, and the next 6 digits denote time. Check if the date and time match those when an error was generated during AAC playback. You can switch between Writer and HDD data, using [FRM/TIM]. Switch according to the type of medium being played back. For USB, there is no log for reading errors. DVR-LX61D...
Page 81
How to diagnose: After setting the unit to Standby mode, turn the unit back on and check if an MEM error is generated. If it is, the system memory may be defective. DVR-LX61D...
Is the IP address set within the ranges shown below? on the left: Ether 2 CLASS A: 10.0.0.1 to 10.255.255.254 If automatic acquisition of an IP address is set to ON, CLASS B: 172.16.0.1 to 172.31.255.254 check the setting of the router. CLASS C: 192.168.0.1 to 192.168.255.254 DVR-LX61D...
(GGF1529). (A long, thin rod about 1 mm in diameter can be used in place of the rod.) SERVICE LOADER Assy ×2 Bonnet SERVICE LOADER Assy ×2 Emergency disc ejection rod (GGF1529) DVR-LX61D...
Page 84
Front Panel Section Unhook the four hooks. Remove the two screws. Remove the two screws. Remove the HDD with the HDD stay. Bottom view Disconnect the one flexible cable. Remove the front panel section. SERVICE TUSB Assy CN105 Front panel section DVR-LX61D...
Page 85
Remove the SERVICE LOADER MAIN. CN902 CN201 CN901 Bottom view POWER SUPPLY SERVICE DVUB Assy Assy CN2301 CN4701 DVR-LX61D Only Remove the two screws. Remove the ETAB Assy while disconnecting the B to B connector. SERVICE LOADER MAIN Bottom view CN501 ETAB Assy DVR-LX61D...
Page 86
Arrange the unit as shown in the photo below. Diagnosis Flexible cable for service Flexible cable for service (24P) (40P) SERVICE TUSB Assy CN102 CN101 CN4701 CN2301 SERVICE LOADER Assy SERVICE DTBR Assy SERVICE MAIN Assy SERVICE LOADER MAIN Front panel section DVR-LX61D...
Page 87
Remove the low case U11. Before shipment, be sure to clean the pickup lens, using the following cleaning materials: Cleaning liquid : GEM1004 Cleaning paper : GED-008 Bottom view Low case U11 Pickup lens SERVICE LOADER Assy SERVICE MAIN Assy Bottom view DVR-LX61D...
3 Disconnect then reconnect the AC power cord of the unit. Be careful not to impart vibration to the unit DVR-LX61D/WY VERSION : 0.14 SYSCON : RELEASE_179 immediately after the AC power cord is disconnected.
To enter the Drive Adjustment Mode, press [ESC]+[CX]+[1]+[0] on the remote control unit for service. Though the LD power adjustment can be executed irrespective of the product functions, do not operate the product during the LD power adjustment to prevent misadjustment. DVR-LX61D...
Page 90
When the checksum is incorrect [12345678910] The input data may be incorrect. CHECK SUM NG! Return to 2 and enter the PU Data Setting [01987654321] Mode to re-enter the 11-digit number. <CLEAR> Exit <STEREO> PU Data Setting <SEARCH> Power Adjustment DVR-LX61D...
Page 91
Step Mode : - Result : OK <CLEAR> Exit If the adjustment for CD disc judgment is not completed successfully • A disc other than CDT-313 may have been placed. Place CDT-313 in the tray. 9. Turn off the power. DVR-LX61D...
Page 92
• The power adjustment may have been unsuccessful. Try the power adjustment again. If the above two do not solve the problem, a defect with MAIN Assy or PU is suspected. DVR-LX61D...
"How to confirm the ID number" shown below. • Input the ID number while the unit is in Stop mode. • After the data are read from the data disc (Type 2), the disc will automatically be unloaded. DVR-LX61D...
Page 94
Before servicing, OBTAIN THE USER'S PRIOR CONSENT to that effect. Execute HOME MENU Setup Disc Setup Intialize Initialize HDD Start *Goes to normal operation with no caution Disc Setup Basic Initialize HDD Start Initialize Finalize Initialize HDD After OSD displaying "Finished" after initilaization, reboot. DVR-LX61D...
Page 95
CLOSE key " " on the player. After confirming this message, press CLEAR key to exit the [Recorder's ID Data Setting] input mode. [Recorder's ID Data Setting] <CLEAR> Exit Rom Write OK ! Insert The ID Data Disc ! <CLEAR> Exit DVR-LX61D...
Page 96
ID Number ? [ 0 0 0 0 0 0 0 0 1] Compare > 0 0 0 0 0 0 0 0 1 OK ? <PLAY> Enter <STOP> Memory Clear <STEREO> ID Data Setting Mode Input ID Number ! DVR-LX61D...
The power turns on and press a " ESC " button, then press " DISP " button on the remote control unit for servicing. Confirm a firmware release version. Press " ESC " button on the remote control unit for servicing in order to exit the test mode. DVR-LX61D...
Page 98
"Communication Error" may come out one to twice, and update may fail. In this case, please click "START" again. • Other factors can be considerd if update fails 3 times or more. • And it takes about 40 minutes for updating the firmware. DVR-LX61D...
Page 99
My Computer. 5. When writing is finished, the disc will be ejected. Production of the disc for updating is completed. When the PC is ready for writing, the window shown will be displayed. DVR-LX61D...
The power turns on and press a " ESC " button, then press " DISP " button on the remote control unit for servicing. Confirm a GNDB B and GNDB U version. Press " ESC " button on the remote control unit for servicing in order to exit the test mode. DVR-LX61D...
Page 101
Perform an HDD check. Is the HDD normal as a File-system error. Initialize the HDD. result of the check? Failure in the HDD. After replacement After initialization, does the of the HDD, redownload the DB. system operate normally? Completed DVR-LX61D...
• The channels to be indicated for "Input Channel" are as shown below: Line inputs: L1-L3, DV (DV is not valid for specific-area settings.) Tuner channels: Channels received by the tuner (channels to be set in Specific-Channel Setting mode, etc.) DVR-LX61D...
Page 103
• If L1, L2, L3, or DV is selected for input, general settings for the line input can be made (DV is not valid for specific-area settings), and if TUNER is selected, general settings for the tuner input can be made. DVR-LX61D...
For the applying amount of lubricants or glue, follow the instructions in this manual. (In the case of no amount instructions, apply as you think it appropriate.) 9.1 PACKING SECTION for WVXK5 type WVXK5 type ONLY WYXK5 type ONLY DVR-560HX ONLY WVXK5 type ONLY DVR-LX61D ONLY WYXK5 type ONLY DVR-LX61D...
Page 107
(Italian) Operating Instructions See Contrast table (2) (Dutch) Operating Instructions See Contrast table (2) (Spanish) (2) CONTRAST TABLE DVR-LX61D/WVXK5, WYXK5, DVR-560HX-S/WVXK5, WYXK5, DVR-560HX-K/WVXK5 and WYXK5 are constructed the same except for the following: DVR-LX61D DVR-LX61D DVR-560HX-S DVR-560HX-S DVR-560HX-K DVR-560HX-K Mark...
9.2 EXTERIOR SECTION DVR-LX61D ONLY Cleaning paper : GED-008 Refer to “9.5 SERVICE LOADER MAIN SECTION”. DVR-LX61D ONLY DVR-560HX ONLY DVR-LX61D ONLY DVR-LX61D ONLY DVR-LX61D ONLY Refer to “9.3 FRONT PANEL SECTION (DVR-LX61D)”, “9.4 FRONT PANEL SECTION (DVR-560HX)”. DVR-LX61D...
Page 109
Writer Stay L VNE2448 NSP 39 Writer Stay R VNE2449 DV Angle See Contrast table (2) Insulator H.S. See Contrast table (2) Rear Panel See Contrast table (2) LAN Angle See Contrast table (2) Earth Plate TU VBK1173 Tray Sheet VEC2551 DVR-LX61D...
Page 110
(2) CONTRAST TABLE DVR-LX61D/WVXK5, WYXK5, DVR-560HX-S/WVXK5, WYXK5, DVR-560HX-K/WVXK5 and WYXK5 are constructed the same except for the following: DVR-LX61D DVR-LX61D DVR-560HX-S DVR-560HX-S DVR-560HX-K DVR-560HX-K Mark Symbol and Description /WVXK5 /WYXK5 /WVXK5 /WYXK5 /WVXK5 /WYXK5 1 ETAB Assy VWV2344 VWV2344 Not used...
9.3 FRONT PANEL SECTION (DVR-LX61D) SERVICE TUSB CN105 to Door Shaft Lubricant Hanarl GEM1041 Paste lubricant hanarl (GEM1041) to salient points of both sides of the door. DVR-LX61D...
Page 113
VBA1113 Door Panel YAH1001 Screw BPZ30P080FTC Main Key YNK1004 Key Top PW YNK1005 (2) CONTRAST TABLE DVR-LX61D/WVXK5 and DVR-LX61D/WYXK5 are constructed the same except for the following: DVR-LX61D DVR-LX61D Mark Symbol and Description /WVXK5 /WYXK5 Front Panel PTD YXA1044 YXA1025...
9.4 FRONT PANEL SECTION (DVR-560HX-S, -K) Lubricant Hanarl GEM1041 SERVICE TUSB CN105 Lubricant Hanarl GEM1041 to Door Shaft Lubricant Hanarl GEM1041 Paste lubricant hanarl (GEM1041) to salient points of both sides of the door. DVR-LX61D...
Page 115
DVR-560HX-S/WVXK5, WYXK5, DVR-560HX-K/WVXK5 and WYXK5 are constructed the same except for the following: DVR-560HX-S DVR-560HX-S DVR-560HX-K DVR-560HX-K Mark Symbol and Description /WVXK5 /WYXK5 /WVXK5 /WYXK5 3 Pioneer Name Plate VAM1148 VAM1148 VAM1153 VAM1153 12 Key Top PW VNK6359 VNK6359 VNK6239 VNK6239 13 Key Top REC VNK6361...
9.5 SERVICE LOADER MAIN SECTION ∗ ∗ ∗ Reuse ( ) marked parts when exachanging SERVICE LOADER Assy. • Case Screw S ∗ (DBA1250) x2 DVR-LX61D...
Page 117
DEB1726 NSP 8 Tape • • • • • Screw BBZ30P060FTC Screw DBA1220 (2) CONTRAST TABLE DVR-LX61D/WVXK5, WYXK5, DVR-560HX-S/WVXK5, WYXK5, DVR-560HX-K/WVXK5 and WYXK5 are constructed the same except for the following: DVR-LX61D DVR-LX61D DVR-560HX-S DVR-560HX-S DVR-560HX-K DVR-560HX-K Mark Symbol and Description...
AT1D15 MD15 MD14 OFPULSE/WRCKP R234 PLL_VDD(1.0V) USB_DN0 USB_D_DN0 DCLKB PKPULSE1M R235 V+1R0 V+1R0_PLL L1021 DTL1106-A-T TP1015 V+3D V+3D GNDD GNDD R1010 X1002 VSS1172-A GNDD 27MHz to HD to US GNDD from to VID to Au to HD to DD DVR-LX61D...
SIDE B P.C.Board Chip Part transistor Resistor array 3-terminal regulator 11.1 SERVICE FRJB ASSY SIDE A SIDE A SERVICE FRJB ASSY CN106 CN301 KN302 CN301 FRJB [[ G ]] KN301 (YNP1006-B) SIDE B SIDE B CN301 (YNP1006-B) SERVICE FRJB ASSY DVR-LX61D...
11.5 ETAB ASSY (DVR-LX61D ONLY) SIDE A SIDE A ETAB ASSY CN1501 CN501 [[ G ]] A30C5/C7 JA301 CN501 X301 F301 F321 IC201 IC202 IC182 IC182 IC181 IC181 X101 IC101 IC101 VNP2100-A F171 VWV2344 C171 (VNP2100-A) SIDE B SIDE B...
IC 401 (A,124,124) IC FOR DVD REC HA118326APFR LIST OF ASSEMBLIES IC 402 (A,149,100) OP-AMP IC BA4560RF IC 403 (A,123,93) VIDEO SW IC MM1503XN 1..ETAB ASSY (DVR-LX61D only) VWV2344 IC 406 (B,67,46) IC TC7S66FU 1..DTBR ASSY VWV2346 IC 601 (A,118,174) MULTI SOUND DECODER MSP3417G 2..SERVICE DTBR ASSY...
Page 175
R 110 (A,211,144) RS1/16S101J D 527 (B,80,48) DIODE 1SS355 R 111 (A,212,149) RS1/16S101J D 528 (B,87,119) DIODE 1SS355 R 112 (A,222,161) RS1/16S103J D 701 (B,55,34) DIODE 1SS355 R 113 (A,219,161) RS1/16S0R0J L 102 (A,200,88) AXIAL INDUCTOR LAU470J R 116 (B,208,153) RS1/16S0R0J DVR-LX61D...
Page 176
R 180 (A,221,132) RS1/16S101J R 407 (A,97,126) RS1/10S0R0J R 181 (A,217,133) RS1/16S101J R 408 (A,148,115) RS1/16S471J R 182 (A,220,134) RS1/16S101J R 410 (A,150,110) RS1/16S471J R 412 (A,148,112) RS1/16S471J R 183 (A,217,134) RS1/16S101J R 184 (A,220,135) RS1/16S101J R 413 (A,148,119) RS1/16S471J DVR-LX61D...
Page 177
R 487 (B,49,151) RS1/16S223J R 488 (B,42,156) RS1/16S471J R 568 (B,70,64) RS1/16S123J R 489 (B,42,161) RS1/16S104J R 569 (B,76,65) RS1/16S102J R 498 (A,120,84) RS1/16S223J R 571 (B,45,92) RS1/10S75R0F R 499 (A,118,82) RS1/16S223J R 573 (B,52,63) RS1/16S0R0J R 574 (B,83,90) RS1/16S0R0J DVR-LX61D...
Page 178
C 123 (A,171,178) ELECT. CAPACITOR CEAT471M6R3 C 329 (B,146,185) CKSRYF104Z25 C 124 (A,189,152) CKSRYF104Z25 C 401 (A,131,111) CKSRYF105Z10 C 125 (A,182,154) CKSRYF104Z25 C 402 (A,138,104) CCSRCH101J50 C 126 (A,185,134) CKSRYF104Z25 C 403 (A,134,105) CCSRCH101J50 C 127 (A,178,114) CEAT101M16 C 404 (A,123,112) CKSRYF105Z10 DVR-LX61D...
Page 179
C 466 (A,118,90) CCSRCH102J50 C 606 (B,48,173) CCSRCH100D50 C 607 (A,72,166) CEAT1R0M50 C 467 (A,121,87) CKSRYF105Z10 C 470 (A,113,84) CKSRYB104K16 C 609 (A,63,168) CEAT101M10 C 471 (A,151,107) CEAT100M50 C 611 (A,56,169) CEAT470M16 C 472 (A,154,95) CEAT100M50 C 613 (B,130,168) CKSRYF105Z10 DVR-LX61D...
Page 180
CCSRCH101J50 R 120 (B,203,65) RS1/16S103J C 754 (B,27,40) CCSRCH101J50 R 121 (B,216,59) RS1/10S221J R 122 (B,216,56) RS1/16S122J SERVICE FLKY ASSY (DVR-LX61D) R 123 (B,210,83) RS1/16S103J MISCELLANEOUS R 124 (B,205,61) RS1/16S102J R 125 (B,81,43) RS1/16S103J IC 101 (B,143,78) FL DRIVER IC...
Page 181
Q 111 (B,98,56) DIGITAL TRANSISTOR DTC124EUA R 132 (B,116,40) RS1/16S332J Q 112 (B,61,49) TRANSISTOR 2SD2153 R 133 (B,117,63) RS1/16S271J Q 203 (B,144,32) DIGITAL TRANSISTOR DTC124EUA R 135 (B,215,40) RS1/16S562J Q 204 (B,79,18) DIGITAL TRANSISTOR DTC124EUA R 137 (B,220,83) RS1/16S0R0J R 138 (B,193,84) RS1/16S0R0J DVR-LX61D...
Page 182
C 204 (B,96,26) CKSRYF104Z25 IC 4511 S-1170B33UC-OTS C 270 (B,143,28) CKSRYF104Z25 IC 4521 S-1170B25UC-OTK IC 4531 MM1701WH SERVICE FRJB ASSY (DVR-LX61D) IC 4541 MM1563DF MISCELLANEOUS IC 4552 S-1170B50UC-OUJ IC 4561 S-1112B50MC-L7J JA 301 (A,211,31) 4P MINIDIN SOCKET(S) AKP1239 IC 4562...
Page 183
CN 1402 07P CONNECTOR RKN1048 R 5651 RS1/16S1202F CN 1501 50P B TO B CONNECTOR VKN2079 R 5664,5672,5705,5830 RS1/16S0R0J CN 2301 40P CONNECTOR VKN2065 R 5706 RS1/16S75R0F R 5825-5828 RAB4CQ220J CN 3801 CONNECTOR CKS5321 R 5855 RAB4CQ100J CN 4501 KR CONNECTOR S13B-PH-K-S DVR-LX61D...
Page 184
C 1048,1052,1056,1059 VCG1057 C 5223,5705,5706,5802 CKSSYB102K50 C 1050,5121,5122,5613 CEVW101M4 C 5602,5702,5707,5801 VCG1057 C 1062,1066,1102,1104 VCG1057 C 5614,5617,5622-5632 CKSSYB103K16 C 1063,1067,1105,1203 CKSSYF104Z16 C 5616,5812,5813 CKSSYF104Z16 C 1064,1065,1068,1101 CKSSYB102K50 C 5704 CEVW1R0M50 C 1103,1207,1209,1210 CKSSYB102K50 C 5803,5805-5808,5820 VCG1057 C 1113,1202,1204,1208 VCG1057 DVR-LX61D...
R 1241,1242,1248,1249 RAB4CQ0R0J Q 5804 DTC124EUA R 1245,1246,1255,1256 RAB4CQ220J Q 5805 2SA1576A R 1261,1262,1268,1269 RAB4CQ0R0J Q 5808 2SK2034 Q 5810 UMF21N R 1265,1266,1273,1274 RAB4CQ220J D 3201 DAN202U R 1281-1283,1287 RAB4CQ470J R 1302,1303,1312,1313 RS1/16S1001F D 4521,4552,4571 RB501V-40 R 1314,2506,4574,4575 RS1/16S0R0J DVR-LX61D...
Page 186
C 153,1020,4516 CEVW100M16 C 3305,3318,3324,3331 CCSSCH150J50 C 156 CKSSYB182K50 C 3307,3313,3319,3325 CKSRYB105K10 C 163,1007,3108,3219 CEVW221M4 C 3314,3315,3320,3321 CCSRCH7R0D50 C 165,166,176,177 CCSSCH220J50 C 3322,3329 CCSSCH5R0C50 C 170,172-174 CCSSCH470J50 C 3330 CCSSCH680J50 C 171,197,504,516 CKSSYB104K10 C 3339-3342,3703,3707 VCG1057 C 182,286,1021,1051 DCH1201 DVR-LX61D...
Page 187
VCG1058 C 5824,5826 VCG1057 C 403,413,417 CKSSYF104Z16 C 5825 CKSSYB102K50 C 418 VCG1057 C 419 VCH1234 ETAB ASSY (DVR-LX61D only) SEMICONDUCTORS SERVICE DVUB ASSY IC 101 UPD99914F1-BAC MISCELLANEOUS IC 181 TC4SU69F IC 182 TC7SZU04FU L 904 (B,218,44) CHIP FERRITE BEADS...
Page 188
C 212 VCG1057 CN 0 CONNECTOR GUIDE VEC2559 C 213,3001-3005 CKSSYF104Z16 CN 102 CONNECTOR VKN2045 C 222,3006,3007,3016 VCG1058 CN 103 CONNECTOR CKS3384 C 301,304,309,338 CKSRYB105K10 C 302,343,385,595 CEVW221M4 CN 201 CONNECTOR VKP2396 CN 203 CONNECTOR POST B2B-PH-K-S C 303,370 CCSRCH101J50 DVR-LX61D...
Page 189
C 406,417,418,421 CKSRYF105Z10 C 409,413,3023 CKSRYB104K16 C 416,422,423,522 CKSRYF104Z25 C 433,602 CKSQYB475K6R3 C 524,593,594,596 CKSRYF104Z25 C 597 CEVW221M4 C 598,600,614,615 CKSRYF104Z25 C 601,3017 CEVW101M16 C 3008-3013 CKSSYF104Z16 C 3022 CCG1205 POWER SUPPLY ASSY POWER SUPPLY ASSY has no service part. DVR-LX61D...
Page 190
PIONEER CORPORATION 4-1, Meguro 1-chome, Meguro-ku, Tokyo 153-8654, Japan PIONEER ELECTRONICS (USA) INC. P.O. Box 1760, Long Beach, CA 90801-1760, U.S.A. PIONEER EUROPE NV Haven 1087, Keetberglaan 1, 9120 Melsele, Belgium PIONEER ELECTRONICS ASIACENTRE PTE. LTD. 253 Alexandra Road, #04-01, Singapore 159936...
Page 191
Ex.2 When there are 3 effective digits (such as in high precision metal film resistors). 562 x 10 5621 RN1/4PC 1.1 CONTRAST TABLE [1] For DVR-LX61D/WPWXV DVR-LX61D/WVXK5 and DVR-LX61D/WPWXV are constructed the same except for the following: Mark Symbol and Description DVR-LX61D/WVXK5 DVR-LX61D/WPWXV Remarks PCB ASSEMBLIES 1..
Page 192
Rear Panel YNA1040 YNA1047 P109-46 Tray Panel PTD YNK1038 YXA1051 P109-49 Serial Label S VRW2017 VRW2188 P109-54 Screw BSZ30P060FTC BSZ30P060FBN P109-64 Screw BSZ30P060FTC BSZ30P060FBN FRONT PANEL SECTION P115-3 Pioneer Name Plate VAM1148 VAM1153 P115-12 Key Top PW VNK6359 VNK6239 DVR-LX61D...
Page 193
YXA1072 YXA1081 CI Cover Not used VNK6229 No. 1 *1: Refer to SERVICE TUSB Assy for DVR-LX61D/WVXK5. Exploded Views Front Panel No. 1 1.2 CONTRAST OF PCB ASSEMBLIES F SERVICE TUSB ASSY YXX1002 and YXX1014 are constructed the same except for the following:...
Page 194
C 614,615 CKSRYF104Z25 R 187 RAB4CQ151J R 188-192 RAB4CQ101J R 239-249,3056,3057 RAB4CQ470J R 250,251 RS1/16SS103J R 253,254,3103-3105 RS1/16SS470J R 595 RS1/16SS560J R 650,703 RS1/10S0R0J R 660,661 RS1/16S1001F R 678,679,694-696 RAB4CQ330J R 698-702,704-707 RS1/16SS330J Other Resistors RS1/16S###J CAPACITORS C 101,107,111,113 CKSRYF105Z10 DVR-LX61D...
Need help?
Do you have a question about the DVR-LX61D and is the answer not in the manual?
Questions and answers